LMR344F-GE2 - Low-Power Quad CMOS Op Amp | ROHM
MPN: LMR344F-GE2 ✓ نشطLMR344F-GE2 نظرة عامة
A CMOS operational amplifier is a voltage-gain device used to amplify weak sensor, audio, or feedback signals while operating from a low-voltage supply. The LMR344F belongs to the operational-amplifier hierarchy, where it provides input-ground sensing and rail-to-rail signal handling for battery-powered equipment, monitoring circuits, and voice audio preamplifiers. Rail-to-rail operation helps preserve usable input and output range when the supply voltage is restricted.
The LMR344F family is designed for low operating supply voltage, low supply current, and low input bias current. Its four amplifiers share a common 14-pin SOP package, reducing board area in designs that require multiple signal-conditioning channels. The input-ground-sensing architecture is especially useful when an input signal is referenced to ground rather than to the midpoint of the supply rails.
Full-swing output operation allows the amplifier outputs to approach the available supply-rail limits under suitable load conditions. This behavior is valuable in low-voltage systems where signal headroom is limited. The exact bandwidth, slew rate, input offset, noise, and output-current limits should be confirmed against the manufacturer datasheet before defining the closed-loop gain, load, and stability target of a new design.
Typical applications include current sensing, portable instrumentation, battery monitoring, sensor signal conditioning, and voice audio preamplification. Multiple amplifiers in one package can support gain stages, differential front ends, filters, output drivers, or active feedback networks when their individual input, output, common-mode, and stability requirements match.
For PCB implementation, use the manufacturer pin-description table to assign inputs, outputs, supply rails, and any unused amplifier channels. Keep input and feedback routing short, connect decoupling capacitors close to the supply pins, and provide stable feedback around each amplifier. Verify operation across the complete supply range and load range rather than assuming rail-to-rail input and output alone guarantees usable bandwidth.
This product page combines the manufacturer product information with practical device classification, application guidance, design notes, and a same-package alternative assessment. It is intended to help engineers identify the correct amplifier function, validate package compatibility, and plan a robust low-voltage analog implementation.
بدائل مباشرة لـ LMR344F-GE2 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
LMR344FJ-GE2
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LMR344F-GE2 الحدود القصوى والخصائص الكهربائية
| Number of Amplifier Channels | 4 circuits |
| Amplifier Type | CMOS operational amplifier |
| Operating Supply Voltage Range | 2.7 V to 5.5 V |
| Input Common-Mode Behavior | Rail-to-rail |
| Output Swing Behavior | Full swing; rail-to-rail output |
| Input Bias Feature | Input ground sense |
| تيار التغذية | 32 mA per channel |
| العلبة | 14-pin SOP, 0.173 in x 4.40 mm body width |
| نوع التركيب | Surface mount |
دليل تكوين أطراف LMR344F-GE2 14-pin sop, 0.173 in x 4.40 mm body width
تكوين الأطراف لـ LMR344F-GE2 (حزمة 14-pin sop, 0.173 in x 4.40 mm body width). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LMR344F-GE2.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LMR344F-GE2 مناسب لـ 6 التطبيقs: Portable Sensor Signal Conditioning, Battery Monitoring and Threshold Control, Voice Audio Preamplification, Current and Voltage Sensing, Precision Analog Measurement Front End, Low-Voltage Output and Feedback Driver.
Portable Sensor Signal Conditioning
The LMR344F-GE2 fits low-voltage sensor front ends because it combines four CMOS amplifier channels with rail-to-rail input operation in a 2.7 V to 5.5 V supply environment. Input ground sensing is useful when the sensor signal is referenced to ground, while the low-power operating characteristics align with portable equipment. Each channel can provide gain or active filtering, and input offset voltage, noise, and common-mode limits should be checked against the sensor output. Place the amplifier and its feedback components close to the sensor interface to reduce parasitic pickup, and use the manufacturer pin table when assigning unused amplifier channels.
موصى به
Battery Monitoring and Threshold Control
The LMR344F-GE2 is appropriate for battery-powered monitoring circuits that operate across low supply rails. Its four channels allow one device to handle cell sensing, reference comparison, filtering, and an output-conditioning stage when all nodes remain within the 2.7 V to 5.5 V operating range. The low input bias current helps avoid loading high-impedance battery dividers, and rail-to-rail input operation supports signals near either supply limit. The designer must still protect inputs against transient battery voltages and verify that the amplifier output can drive the required load and remain within its guaranteed output swing.
موصى به
Voice Audio Preamplification
The LMR344F-GE2 supports voice audio preamplification because the LMR344F family is identified for low-voltage audio preamplifier applications. Four channels in one 14-pin SOP can support microphone gain, filtering, mixing, or output buffering while conserving board area. Rail-to-rail input operation helps accommodate low-voltage microphone signals, and full-swing output supports amplitude utilization on a restricted supply. Verify input-noise density, gain accuracy, output swing, and channel matching in the manufacturer electrical characteristics, and use short, shielded routing for microphone inputs to prevent acoustic and electrical pickup.
موصى به
Current and Voltage Sensing
The LMR344F-GE2 can condition outputs from low-voltage current and voltage sensors when low input bias current and rail-to-rail input behavior are important. Four channels permit sharing a package across sensing, filtering, gain, and reference stages, reducing component count in compact measurement electronics. Input ground sensing is beneficial when the transducer signal is ground-referenced. The circuit remains usable only if the sensor common-mode voltage and shunt voltage stay inside the amplifier's specified range. Confirm shunt-generated signal polarity, input offset error, output-current capability, and stability with the selected feedback network before release.
موصى به
Precision Analog Measurement Front End
The LMR344F-GE2 suits measurement front ends that require several low-voltage gain stages around a converter or instrumentation block. The four-channel 14-SOP package can implement differential amplification, anti-alias filtering, level shifting, and output buffering without using four separate packages. Its input-ground-sense architecture supports ground-referenced measurement chains, while the 2.7 V to 5.5 V supply range supports compact laboratory and industrial equipment. For precision results, evaluate offset voltage, bias current, noise, channel matching, and the gain error of the selected resistors against the measurement budget.
موصى به
Low-Voltage Output and Feedback Driver
The LMR344F-GE2 can serve as a low-voltage buffer or feedback amplifier where full-swing output and rail-to-rail input behavior improve usable signal range. Four independent channels support gain-stage, active-feedback, filtering, and auxiliary buffering functions within one 14-pin SOP package. This consolidation is useful in compact control and monitoring electronics powered from a 2.7 V to 5.5 V source. Because full swing does not guarantee the same output range at every load, verify the required load current, capacitive-load tolerance, gain bandwidth, and phase margin. Maintain short feedback paths and provide local supply bypassing to limit instability and supply ripple coupling.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LMR344F-GE2 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LMR344FJ-GE2 |
|---|---|---|
| Package | 14-SOP | 14-SOPJ |
| Brand | ROHM Semiconductor | ROHM Semiconductor |
| Amplifier Channels | 4 | 4 |
| Operating Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
أبرز الفروقات
- Four low-power amplifier channels in one package (مقابلLMR344FJ-GE2)
- Ground-referenced input architecture (مقابلLMR344FJ-GE2)
- Low-voltage operation with rail-to-rail signal handling (مقابلLMR344FJ-GE2)
ملاحظات التصميم
Place the local supply-decoupling capacitor immediately between each supply pin and ground, with a short return path that does not share a long trace with the amplifier input. Keep each operational amplifier's feedback components adjacent to the associated pins, and route the non-inverting input away from clocks, switching regulators, inductors, and high-current return paths. The 14-pin SOP footprint should be created from the exact manufacturer land pattern rather than inferred from package width alone.
Check the selected closed-loop gain against the device's gain-bandwidth and phase-margin behavior. Rail-to-rail input and full-swing output describe voltage-range capability, but they do not guarantee equal bandwidth or phase margin near either supply rail. For sensor and audio signals, use short traces, guard grounded areas where appropriate, and maintain a stable feedback topology. Confirm capacitive-load tolerance before driving long cables, ADC inputs, or other high-capacitance nodes.
Calculate the amplifier's total supply demand for all four channels at the minimum intended load condition. The listed supply current is 32 mA per channel, so four active channels correspond to an estimated aggregate supply demand of 128 mA before considering other circuit loads. The regulator must support this current plus transient margin, and the power rail must remain within 2.7 V to 5.5 V at the device pins under worst-case supply and temperature conditions.
Do not infer a pin-compatible replacement solely from matching amplifier channel count, voltage rating, and package dimensions. The identified LMR344FJ-GE2 uses a 14-SOPJ listing while the target uses a 14-SOP designation; verify pin numbering, land pattern, exposed dimensions, electrical limits, and lead finish with the manufacturer documentation before substitution. Also follow the datasheet instructions for unused amplifier channels instead of allowing their inputs to float.
معلومات الامتثال
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement appears in the manufacturer and distributor information for this exact MPN.