LPC2368FBD100 - ARM7 72MHz 512KB Flash MCU | NXP
MPN: LPC2368FBD100 ✓ نشطLPC2368FBD100 نظرة عامة
An ARM7 microcontroller is a 32-bit RISC processor core that executes both the 32-bit ARM and the 16-bit Thumb instruction set, allowing code-density and performance trade-offs. The ARM7TDMI-S variant adds a hardware multiplier and embedded ICE debug logic. Within NXP's portfolio, the LPC2300 family sits at the top of the legacy LPC2000 ARM7 line, ahead of the smaller LPC2100 and LPC2200 series, and is itself succeeded by the Cortex-M3 based LPC1700 family. Peripherals are tightly integrated to minimize external components in industrial Ethernet, USB, and CAN nodes. The device operates from a single 3.0 V to 3.6 V supply, with I/O tolerant to 5 V, and is housed in a 100-pin LQFP (14 x 14 mm) package suitable for cost-sensitive 4-layer PCB layouts.
Key features include 72 MHz maximum CPU clock with on-chip PLL, 32 kB SRAM usable as battery-backed retention, vectored interrupt controller for deterministic real-time response, and ISP/IAP in-application programming via UART or CAN. The Ethernet MAC supports 10/100 Mbps MII/RMII with full-duplex operation, while the USB 2.0 controller supports device, host, and OTG roles. The ADC delivers 400 ksps across 8 channels at 10-bit resolution, and the DAC is a 10-bit rail-to-rail converter suitable for waveform generation.
Typical applications include industrial Ethernet gateways, building automation controllers, USB peripherals and embedded hosts, CAN-based automotive body modules, point-of-sale terminals, and small-scale motor-control boards. Designers choose the LPC2368FBD100 when ARM7 firmware, a wide peripheral mix, and 512 kB of on-chip flash are required without an external memory bus.
When designing with this device, ensure the 3.3 V analog supply (V3A) is decoupled with at least 100 nF plus a 10 uF bulk, and isolate it from the digital 3.3 V plane to avoid ADC/DAC noise coupling. The VBAT domain supports RTC backup and 32 kB of retained SRAM; route a small lithium cell or supercap there to preserve RTC time across power cycles.
بدائل مباشرة لـ LPC2368FBD100 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LPC2368FBD100 (نفس عامل الشكل والبصمة) — يختلف في ADC, DAC, Ethernet MAC, Operating Temperature, Package.
LPC2364FET100
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LPC2366FBD100
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LPC2367FBD100
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LPC2368FBD100K
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LPC2368FBD100-S
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LPC2368FBD100 الحدود القصوى والخصائص الكهربائية
| Core Architecture | ARM7TDMI-S (16/32-bit) |
| Maximum CPU Clock | 72 MHz |
| Flash Memory | up to 512 kB |
| SRAM | up to 58 kB (32 kB battery-backed) |
| Supply Voltage (Vdd) | 3.0 V to 3.6 V |
| I/O Voltage Tolerance | 5 V tolerant |
| Ethernet MAC | 10/100 Mbps MII/RMII |
| USB Controller | USB 2.0 Device/Host/OTG |
| ADC | 10-bit, 8-channel, 400 ksps |
| DAC | 10-bit |
| CAN Channels | 2 (CAN 2.0B) |
| UART | 4 |
| SSP/SPI | 3 |
| I2C | 3 |
| I2S | 1 |
| PWM | 2 (Motor Control PWM) |
| General-Purpose Timers | 4 |
| DMA Controller | Yes (GPDMA) |
| External Memory Bus | Yes (8/16/32-bit) |
| العلبة | LQFP-100 (14 x 14 mm, 0.5 mm pitch) |
| درجة حرارة التشغيل | -40 C to +85 C |
| حالة RoHS | Compliant |
تكوين أطراف LPC2368FBD100
| دبوس 1 | P0[0]/TXD3 — GPIO / UART3 TXD |
| دبوس 2 | P0[1]/RXD3 — GPIO / UART3 RXD |
| دبوس 3 | P0[2]/SCL1 — GPIO / I2C1 SCL |
| دبوس 4 | P0[3]/SDA1 — GPIO / I2C1 SDA |
| دبوس 5 | P0[4]/SCK0/CAP2[0] — GPIO / SSP0 SCK / Timer2 capture |
| دبوس 6 | P0[5]/MISO0/MAT2[0] — GPIO / SSP0 MISO / Timer2 match |
| دبوس 7 | P0[6]/MOSI0/MAT2[1] — GPIO / SSP0 MOSI / Timer2 match |
| دبوس 8 | P0[7]/SSEL0/MAT2[2] — GPIO / SSP0 SSEL / Timer2 match |
| دبوس 9 | P0[8]/TXD2/MAT2[3] — GPIO / UART2 TXD / Timer2 match |
| دبوس 10 | P0[9]/RXD2/MAT3[0] — GPIO / UART2 RXD / Timer3 match |
| دبوس 11 | P0[10]/SDA2/MAT3[1] — GPIO / I2C2 SDA / Timer3 match |
| دبوس 12 | P0[11]/SCL2/MAT3[2] — GPIO / I2C2 SCL / Timer3 match |
| دبوس 13 | P0[12]/MISO1/AD0[6] — GPIO / SSP1 MISO / ADC0 ch6 |
| دبوس 14 | P0[13]/MOSI1/AD0[7] — GPIO / SSP1 MOSI / ADC0 ch7 |
| دبوس 15 | P0[14]/SSEL1/USB_SCL — GPIO / SSP1 SSEL / USB SCL |
| دبوس 16 | P0[15]/USB_SDA — GPIO / USB SDA |
| دبوس 17 | P0[16]/RXD1/SSEL0/CAP1[0] — GPIO / UART1 RXD / SSP0 SSEL / Timer1 capture |
| دبوس 18 | P0[17]/TXD1/CAP1[1] — GPIO / UART1 TXD / Timer1 capture |
| دبوس 19 | P0[18]/DCD1/CAP1[2] — GPIO / UART1 DCD / Timer1 capture |
| دبوس 20 | P0[19]/DSR1/CAP1[3] — GPIO / UART1 DSR / Timer1 capture |
| دبوس 21 | P0[20]/DTR1/MAT1[0] — GPIO / UART1 DTR / Timer1 match |
| دبوس 22 | P0[21]/RI1/MAT1[1] — GPIO / UART1 RI / Timer1 match |
| دبوس 23 | P0[22]/RTS1/MAT1[2] — GPIO / UART1 RTS / Timer1 match |
| دبوس 24 | P0[23]/CTS1/MAT1[3] — GPIO / UART1 CTS / Timer1 match |
| دبوس 25 | P0[24]/PWM1[1]/AD0[1] — GPIO / PWM1 channel 1 / ADC0 ch1 |
| دبوس 26 | P0[25]/AOUT — GPIO / DAC output |
| دبوس 27 | P0[26]/AD0[3]/RXD3 — GPIO / ADC0 ch3 / UART3 RXD |
| دبوس 28 | P0[27]/SCL0 — GPIO / I2C0 SCL |
| دبوس 29 | P0[28]/SDA0/MAT0[0] — GPIO / I2C0 SDA / Timer0 match |
| دبوس 30 | P0[29]/USB_D+ — GPIO / USB D+ |
| دبوس 31 | P0[30]/USB_D- — GPIO / USB D- |
| دبوس 32 | P0[31]/USB_VBUS — GPIO / USB VBUS sense |
| دبوس 33 | Vss — Ground |
| دبوس 34 | Vdd — Digital 3.3 V supply |
| دبوس 35 | Vdd — Digital 3.3 V supply |
| دبوس 36 | P1[0]/ENET_TXD0 — GPIO / Ethernet MAC TXD0 |
| دبوس 37 | P1[1]/ENET_TXD1 — GPIO / Ethernet MAC TXD1 |
| دبوس 38 | P1[4]/ENET_TX_EN — GPIO / Ethernet MAC TX_EN |
| دبوس 39 | P1[8]/ENET_CRS — GPIO / Ethernet MAC CRS |
| دبوس 40 | P1[9]/ENET_RXD0 — GPIO / Ethernet MAC RXD0 |
| دبوس 41 | P1[10]/ENET_RXD1 — GPIO / Ethernet MAC RXD1 |
| دبوس 42 | P1[14]/ENET_RX_ER — GPIO / Ethernet MAC RX_ER |
| دبوس 43 | P1[15]/ENET_REF_CLK — GPIO / Ethernet MAC reference clock |
| دبوس 44 | P1[16]/ENET_MDC — GPIO / Ethernet MAC MDC |
| دبوس 45 | P1[17]/ENET_MDIO — GPIO / Ethernet MAC MDIO |
| دبوس 46 | P1[18]/PWM1[1]/CAP1[0] — GPIO / PWM1 ch1 / Timer1 capture |
| دبوس 47 | P1[19]/MCPWM0_ABORT — GPIO / Motor PWM abort |
| دبوس 48 | P1[20]/MCI0_FB — GPIO / Motor PWM feedback |
| دبوس 49 | P1[21]/PWM0[5]/MCFB0 — GPIO / PWM0 ch5 / Motor control FB0 |
| دبوس 50 | P1[22]/PWM0[4]/MCFB1 — GPIO / PWM0 ch4 / Motor control FB1 |
| دبوس 51 | P1[23]/PWM0[2]/MCFB2 — GPIO / PWM0 ch2 / Motor control FB2 |
| دبوس 52 | P1[24]/PWM0[3] — GPIO / PWM0 ch3 |
| دبوس 53 | P1[25]/PWM0[1] — GPIO / PWM0 ch1 |
| دبوس 54 | P1[26]/PWM0[0] — GPIO / PWM0 ch0 |
| دبوس 55 | P1[27]/CLKOUT — GPIO / CLKOUT |
| دبوس 56 | P1[28]/MAT0[0]/PWM1[2] — GPIO / Timer0 match / PWM1 ch2 |
| دبوس 57 | P1[29]/MAT0[1]/PWM1[3] — GPIO / Timer0 match / PWM1 ch3 |
| دبوس 58 | P1[30]/AD0[4] — GPIO / ADC0 ch4 |
| دبوس 59 | P1[31]/AD0[5] — GPIO / ADC0 ch5 |
| دبوس 60 | Vss — Ground |
| دبوس 61 | Vdd — Digital 3.3 V supply |
| دبوس 62 | P2[0]/PWM1[1]/DQFLAGIN — GPIO / PWM1 ch1 / SDRAM DQ flag in |
| دبوس 63 | P2[1]/PWM1[2]/DQFLAGOUT — GPIO / PWM1 ch2 / SDRAM DQ flag out |
| دبوس 64 | P2[2]/PWM1[3]/D13 — GPIO / PWM1 ch3 / EMD data 13 |
| دبوس 65 | P2[3]/PWM1[4]/D14 — GPIO / PWM1 ch4 / EMD data 14 |
| دبوس 66 | P2[4]/PWM1[5]/D15 — GPIO / PWM1 ch5 / EMD data 15 |
| دبوس 67 | P2[5]/PWM1[6]/D16 — GPIO / PWM1 ch6 / EMD data 16 |
| دبوس 68 | P2[6]/PWM1[7]/D17 — GPIO / PWM1 ch7 / EMD data 17 |
| دبوس 69 | P2[7]/D18 — GPIO / EMD data 18 |
| دبوس 70 | P2[8]/D19 — GPIO / EMD data 19 |
| دبوس 71 | P2[9]/D20 — GPIO / EMD data 20 |
| دبوس 72 | P2[10]/D21 — GPIO / EMD data 21 |
| دبوس 73 | P2[11]/D22 — GPIO / EMD data 22 |
| دبوس 74 | P2[12]/D23 — GPIO / EMD data 23 |
| دبوس 75 | P2[13]/D24 — GPIO / EMD data 24 |
| دبوس 76 | P2[14]/D25 — GPIO / EMD data 25 |
| دبوس 77 | P2[15]/D26 — GPIO / EMD data 26 |
| دبوس 78 | P2[16]/D27 — GPIO / EMD data 27 |
| دبوس 79 | P2[17]/D28 — GPIO / EMD data 28 |
| دبوس 80 | P2[18]/D29 — GPIO / EMD data 29 |
| دبوس 81 | P2[19]/D30 — GPIO / EMD data 30 |
| دبوس 82 | P2[20]/D31 — GPIO / EMD data 31 |
| دبوس 83 | P2[21]/A22 — GPIO / External memory address 22 |
| دبوس 84 | P2[22]/A23 — GPIO / External memory address 23 |
| دبوس 85 | P2[23]/A20/OE — GPIO / Address 20 / Output enable |
| دبوس 86 | P2[24]/A21/BLS3 — GPIO / Address 21 / Byte lane strobe 3 |
| دبوس 87 | P2[25]/CS1 — GPIO / Chip select 1 |
| دبوس 88 | P2[26]/CS2 — GPIO / Chip select 2 |
| دبوس 89 | P2[27]/CS3 — GPIO / Chip select 3 |
| دبوس 90 | P2[28]/A19/CLKOUT2 — GPIO / Address 19 / CLKOUT2 |
| دبوس 91 | P2[29]/A18/CLKOUT3 — GPIO / Address 18 / CLKOUT3 |
| دبوس 92 | P2[30]/A17 — GPIO / Address 17 |
| دبوس 93 | P2[31]/A16 — GPIO / Address 16 |
| دبوس 94 | RTCK — JTAG RTCK (return clock) |
| دبوس 95 | TMS — JTAG TMS |
| دبوس 96 | TDO — JTAG TDO |
| دبوس 97 | TDI — JTAG TDI |
| دبوس 98 | TCK — JTAG TCK |
| دبوس 99 | RSTOUT — Reset output |
| دبوس 100 | RESET — External reset input (active low) |
التطبيقات النموذجية
LPC2368FBD100 مناسب لـ 7 التطبيقs: Industrial Ethernet Gateway / PLC, USB Embedded Host / Device Controller, Building Automation / HVAC Controller, Automotive Body / CAN Gateway Module, Point-of-Sale (POS) Terminal, Small-Scale Motor Control / BLDC Driver, Data Acquisition / Industrial Sensor Hub.
Industrial Ethernet Gateway / PLC
The LPC2368FBD100's on-chip 10/100 Ethernet MAC and full-duplex MII/RMII make it an ideal main controller for Modbus TCP, EtherNet/IP, or PROFINET gateways, replacing external MAC chips. Its ARM7TDMI-S at 72 MHz delivers sufficient headroom for TCP/IP stacks while two CAN 2.0B channels allow bridging to legacy industrial buses. Placed on a 4-layer board with a 3.3 V analog island, it gives deterministic performance with 32 kB of battery-backed SRAM retaining configuration across power loss.
موصى به
USB Embedded Host / Device Controller
The LPC2368FBD100's integrated USB 2.0 controller supports Device, Host, and OTG roles, allowing firmware-driven USB stacks for mass-storage hosts, HID peripherals, or CDC devices without an external interface IC. The on-chip 512 kB flash accommodates USB class drivers and FAT32 file systems, while 58 kB SRAM buffers bulk transfers. Compared to discrete USB solutions it removes BOM cost and PCB area, especially when paired with the on-chip DMA controller to offload endpoint handling from the CPU.
موصى به
Building Automation / HVAC Controller
Building automation controllers need a wide peripheral mix on a single chip - the LPC2368FBD100 provides 4 UARTs for RS-485 trunks, 3 I2C buses for sensor and EEPROM access, an SD/MMC interface for local data logging, and an 8-channel 10-bit ADC for analog temperature and humidity inputs. The 32 kB battery-backed SRAM preserves scheduler state across power cycles, while the RTC with VBAT domain keeps accurate time-stamping. Its 3.0-3.6 V supply with 5 V tolerant I/O allows direct connection to industrial 24 V conditioned sensor lines.
موصى به
Automotive Body / CAN Gateway Module
Automotive body controllers and CAN gateways benefit from the LPC2368FBD100's dual CAN 2.0B channels and 72 MHz ARM7 core running OBD-II or CANopen stacks. Although the part is not AEC-Q100 qualified (it is industrial grade -40 to +85 C), it remains widely used in non-safety automotive nodes such as infotainment auxiliary MCUs and diagnostic bridges. The Ethernet MAC plus dual CAN combination is uniquely strong for telematics control units forwarding CAN traffic over automotive Ethernet.
موصى به
Point-of-Sale (POS) Terminal
POS terminals need USB, Ethernet, multiple serial peripherals, and secure firmware storage - the LPC2368FBD100's 512 kB flash supports encrypted boot loaders, its 58 kB SRAM handles transaction buffers, and its on-chip USB OTG allows direct connection to printers or PIN pads. Compared to Cortex-M0 alternatives, the 72 MHz ARM7 delivers faster DES/AES for legacy payment flows. The LQFP-100 package and 5 V-tolerant GPIO simplify mixed-voltage peripheral boards.
موصى به
Small-Scale Motor Control / BLDC Driver
The LPC2368FBD100 includes 2 dedicated motor-control PWM blocks with quadrature encoder input, suited to small BLDC or stepper control up to a few hundred watts. The 10-bit ADC samples back-EMF and current sense, while the 10-bit DAC provides a programmable reference. ARM7 latency at 72 MHz is fast enough for 20 kHz PWM loops with PI control, and the dual CAN channels expose drive status to a vehicle or machine network.
موصى به
Data Acquisition / Industrial Sensor Hub
Industrial sensor hubs route analog inputs to Ethernet or CAN backbones - the LPC2368FBD100's 8-channel 10-bit ADC at 400 ksps handles multi-sensor scanning, while its on-chip Ethernet MAC streams the data to a SCADA server. With 58 kB SRAM it can buffer 4 kSamples between transmissions. The 5 V tolerant GPIO accepts legacy 4-20 mA loop signals through external resistor networks without additional level shifters, simplifying the analog front end.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LPC2368FBD100 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LPC2364FET100 | LPC2366FBD100 | LPC2367FBD100 | LPC2368FBD100K |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | LQFP-100 (14x14 mm) | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same | LQFP-100 (14x14 mm) - same |
| Core Architecture | ARM7TDMI-S 72 MHz | ARM7TDMI-S 72 MHz | ARM7TDMI-S 72 MHz | ARM7TDMI-S 72 MHz | ARM7TDMI-S 72 MHz |
| Flash Memory | 512 kB | 128 kB (-75%) | 256 kB (-50%) | 512 kB (same) | 512 kB (same) |
| Ethernet MAC | 10/100 MII/RMII | 10/100 MII/RMII | 10/100 MII/RMII | 10/100 MII/RMII | 10/100 MII/RMII |
| USB Controller | USB 2.0 Device/Host/OTG | USB 2.0 Device/Host/OTG | USB 2.0 Device/Host/OTG | USB 2.0 Device/Host/OTG | USB 2.0 Device/Host/OTG |
| CAN Channels | 2 | 2 | 2 | 2 | 2 |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
أبرز الفروقات
- Highest flash density in the LPC236x LQFP-100 family (مقابلLPC2366FBD100)
- Largest SRAM with battery backup (مقابلLPC2367FBD100)
- Integrated Ethernet MAC plus USB OTG plus dual CAN in one chip (مقابلSTM32F107VBT6 (closest cross-brand competitor))
ملاحظات التصميم
The LPC2368FBD100 has separate digital (Vdd) and analog (V3A/Vdda) supply domains. Per the NXP datasheet, decouple each Vdd pin with 100 nF X7R plus a shared 10 uF bulk, and isolate V3A with a ferrite from Vdd to minimize ADC and DAC noise. VBAT should be tied to a small lithium cell or supercap through a 1 kohm isolation resistor to retain the RTC and 32 kB backup SRAM across power loss.
The LQFP-100 (14 x 14 mm, 0.5 mm pitch) package benefits from a 4-layer PCB with a continuous ground plane on layer 2. Keep Ethernet MAC traces (P1[0..17]) short and length-matched within 25 mm to the PHY (KSZ8041 etc.) to avoid MII timing violations. Place the 12 MHz crystal within 5 mm of XTAL1/XTAL2 with a guarded ground ring to suppress EMI from the 72 MHz PLL output.
Do NOT assume the LPC1768FBD100 is a drop-in replacement - it is a Cortex-M3 part with different pin mapping (notably pin 13). ISP/IAP via UART0 requires the external pins P0[14] and P0[15] to be configured correctly during reset; if the BOOT pins are mis-pulled, firmware can lock itself out and require JTAG recovery. The USB_VBUS pin (P0[31]) must be connected even if USB is unused, otherwise VBUS sensing fails and the USB block cannot enter suspend correctly.
Estimated: at 72 MHz CPU clock with all peripherals active, the LPC2368FBD100 typically draws 40-55 mA from Vdd (3.3 V). Power dissipation is therefore ~150 mW, well within the LQFP-100 thermal resistance of approximately 50 C/W (per NXP package data). No heatsink is required, but designers should still provide continuous copper under the exposed die-pad-adjacent ground leads for best thermal relief in enclosed industrial housings.
The on-chip Ethernet MAC drives MII/RMII signals at 25 MHz / 50 MHz respectively - keep these traces over a continuous ground plane and series-terminate (33 ohm) near the MAC if the PHY is more than 50 mm away. USB D+/D- traces require 90-ohm differential impedance and should not have stubs; route them on the top layer only and keep total length below 50 mm.
معلومات الامتثال
RoHS and REACH compliant per NXP product page. Not AEC-Q100 qualified - this is an industrial-grade part (-40 C to +85 C). For automotive body modules the LPC2368 is generally acceptable in non-safety nodes but safety-critical ECUs should use an AEC-Q100 qualified MCU such as the NXP S32K series. Conflict-minerals statement available from NXP.
