LSF0108PWR - 8-Ch Bidirectional Level Translator | TI
MPN: LSF0108PWR ✓ نشطLSF0108PWR نظرة عامة
A voltage level translator is an interface IC that lets digital signals in different voltage domains communicate safely by shifting signal levels as they pass between two logic families. Within the system hierarchy, a level translator is a type of logic interface IC within the broader integrated circuits category. The LSF0108 uses a pass-gate (series MOSFET) architecture with external pull-up resistors, providing automatic direction sensing without a direction-control pin.
Key features include bidirectional translation without a direction pin, support for both open-drain and push-pull drivers, and an operating temperature range of -40C to +125C. The LSF family covers the 0.95 V to 5 V translation range, spanning nearly all common logic levels (1.2V, 1.8V, 2.5V, 3.3V, 5V). Low standby current and the compact TSSOP-20 footprint suit space-constrained mixed-voltage boards.
Technically, each channel employs a series pass transistor. Direction is determined automatically by whichever side drives, eliminating direction-control signals and simplifying firmware. The reference side (VREF_A or VREF_B) sets the lower voltage domain; pull-up resistors on the opposite side set the higher domain.
Typical applications include I2C bus level shifting between 1.8V and 3.3V or 5V domains, UART interfacing between microcontrollers and peripherals, SPI communication between different logic voltages, and mixed-voltage sensor or memory interfaces.
Design tip: size external pull-up resistors according to bus capacitance and target speed (1-10 kOhm for 400 kHz I2C). Correct VREF sequencing at power-up is essential; refer to TI datasheet SCPS229 for power-up requirements.
بدائل مباشرة لـ LSF0108PWR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LSF0108PWR (نفس عامل الشكل والبصمة) — يختلف في Channels, Features, Output Type.
LSF0108PW-Q100J
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LSF0108QPWRQ1
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←TXS0108EQPWRQ1
⚡ نفس الحزمةتواصل لمعرفة السعر
عرض ورقة البيانات ←TXB0108QPWRQ1
⚡ نفس الحزمةتواصل لمعرفة السعر
عرض ورقة البيانات ←TXB0108PWR
⚡ نفس الحزمة ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←LSF0108PWR المواصفات
| Translator Type | Voltage Level Translator |
| القنوات | 8 |
| Circuits | 1 |
| Direction | Bidirectional (auto-direction sensing) |
| A-Side Voltage Range | 0 V to 5 V |
| B-Side Voltage Range | 0 V to 5 V |
| Translation Range (Family) | 0.95 V to 5 V |
| Propagation Delay | Approx. 1.5 ns |
| نوع الخرج | Open-Drain / Push-Pull |
| الميزات | No direction pin required |
| درجة حرارة التشغيل | -40C to +125C |
| العلبة | 20-TSSOP (PW) |
| نوع التركيب | Surface Mount |
| Applications | I2C, SMBus, UART, SPI |
| Logic Family Compatibility | Multi-voltage level translation |
| حالة RoHS | Compliant |
تكوين أطراف LSF0108PWR
| دبوس 1 | A1 — A-side data port 1 (low-voltage domain) |
| دبوس 2 | A2 — A-side data port 2 |
| دبوس 3 | A3 — A-side data port 3 |
| دبوس 4 | A4 — A-side data port 4 |
| دبوس 5 | GND — Ground |
| دبوس 6 | A5 — A-side data port 5 |
| دبوس 7 | A6 — A-side data port 6 |
| دبوس 8 | A7 — A-side data port 7 |
| دبوس 9 | A8 — A-side data port 8 |
| دبوس 10 | OE — Output enable (connect high to enable) |
| دبوس 11 | B8 — B-side data port 8 |
| دبوس 12 | B7 — B-side data port 7 |
| دبوس 13 | B6 — B-side data port 6 |
| دبوس 14 | B5 — B-side data port 5 |
| دبوس 15 | GND — Ground |
| دبوس 16 | B4 — B-side data port 4 |
| دبوس 17 | B3 — B-side data port 3 |
| دبوس 18 | B2 — B-side data port 2 |
| دبوس 19 | B1 — B-side data port 1 |
| دبوس 20 | VREF_B — B-side reference voltage supply |
التطبيقات النموذجية
LSF0108PWR مناسب لـ 6 التطبيقs: I2C Bus Level Shifting, UART Interface Translation, SPI Mixed-Voltage Interfacing, Industrial Control Systems, Portable and Battery-Powered Devices, Automotive Infotainment and Body Electronics.
I2C Bus Level Shifting
The LSF0108PWR is purpose-built for I2C and SMBus level translation between 1.8V, 3.3V, and 5V domains. Its pass-gate architecture with external pull-up resistors (typically 1-10 kOhm) supports open-drain bidirectional signaling with automatic direction sensing, so no DIR pin or firmware control is needed. The approx. 1.5 ns pass-through delay adds negligible timing overhead even at 400 kHz Fast-mode or 1 MHz Fast-mode Plus operation, provided pull-ups are sized to the bus capacitance.
موصى به
UART Interface Translation
UART links between a 1.8V microcontroller and a 3.3V or 5V peripheral run through the LSF0108PWR with one channel per TX/RX line. Push-pull UART signals pass through the series pass transistor with about 1.5 ns delay; pull-up resistors restore the high level on the higher-voltage side. Because the LSF is direction-agnostic, it handles full-duplex TX and RX lines without any control signal, simplifying mixed-voltage MCU-to-module designs such as GPS, Bluetooth, or cellular modules.
موصى به
SPI Mixed-Voltage Interfacing
SPI clocks up to tens of MHz remain usable through the LSF0108PWR thanks to its ~1.5 ns propagation delay, though series pass-gate translators attenuate signal swing and rely on pull-ups, so keep traces short and use low-value pull-ups (1-2 kOhm) for high-speed SCK and MOSI lines. It is commonly used to connect 3.3V SPI flash or sensors to 1.8V MCU domains. For very high SPI rates, evaluate TXS0108E or dedicated push-pull translators instead.
موصى به
Industrial Control Systems
Industrial mixed-voltage backplanes often combine 5V legacy logic with 3.3V or 1.8V modern controllers. The LSF0108PWR bridges these domains across eight channels in one TSSOP-20, operating from -40C to +125C to meet industrial temperature requirements. Its low standby current suits always-on control nodes, and auto-direction sensing means no firmware changes when migrating an existing 5V board to a lower-voltage processor family.
موصى به
Portable and Battery-Powered Devices
Battery-powered designs frequently pair a low-voltage (1.8V) low-power MCU with 3.3V sensors, displays, or memory cards. The LSF0108PWR consumes minimal standby current and requires no active drivers, making it energy-efficient for sleep-mode retention. Eight channels in a compact 20-TSSOP conserve board area in wearables and handheld instruments, and pull-up resistor values can be increased (10 kOhm) to further cut idle current on slow buses like I2C.
موصى به
Automotive Infotainment and Body Electronics
For automotive designs, the pin-compatible Nexperia LSF0108PW-Q100J (AEC-Q100) and TI's TXB0108QPWRQ1 provide qualified 8-bit translation options on the same TSSOP-20 footprint. Automotive ECUs routinely mix 5V sensor rails with 3.3V processors; the LSF architecture's open-drain support handles LIN/K-line style and I2C diagnostics buses, while the -40C to +125C range covers under-dash and engine-bay ambient conditions per the base device rating.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LSF0108PWR — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LSF0108PW-Q100J | LSF0108 | TXS0108EQPWR | TXB0108QPWRQ1 |
|---|---|---|---|---|---|
| Package | TSSOP-20 (PW) | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same | TSSOP-20 (PW) - same |
| Brand | Texas Instruments | Nexperia | Diodes Incorporated | Texas Instruments | Texas Instruments |
| Channels | 8 | 8 | 8 | 8 | 8 |
| Architecture | Pass-gate with external pull-ups | Pass-gate with external pull-ups | Pass-gate with external pull-ups | Integrated one-shot drivers | Integrated drivers (auto-direction) |
| Voltage Range | 0.95 V to 5 V | 0.95 V to 5 V | 0.95 V to 5 V | 1.2 V to 3.6 V (VCCA) / 1.65-5.5 V (VCCB) | 1.2 V to 3.6 V / 1.65-5.5 V |
| Open-Drain Support | Yes (native) | Yes (native) | Yes (native) | Limited (weak one-shot) | Limited |
| Direction Pin | None (auto) | None (auto) | None (auto) | None (auto) | None (auto) |
| Automotive Grade | No | Yes (AEC-Q100) | No | No (Q1 variant exists) | Yes (AEC-Q100) |
أبرز الفروقات
- Native open-drain bus support (I2C/SMBus) (مقابلTXS0108EQPWR)
- Wider low-voltage capability (مقابلTXB0108QPWRQ1)
- Automotive-qualified drop-in available (مقابلLSF0108PW-Q100J)
ملاحظات التصميم
Power-up sequencing is critical: the VREF supply of the reference (lower-voltage) side must be stable before or rise together with the other rail, otherwise outputs can be undefined or latch incorrectly. TI datasheet SCPS229 section on power-up requirements details the valid sequencing. Add a supervisor or RC delay if rail order is uncontrolled.
The LSF pass-gate attenuates signal swing, so the high level on the higher-voltage side is set entirely by the pull-up resistor. Size pull-ups against bus capacitance: 1-2 kOhm for fast SPI/SCK lines, 4.7-10 kOhm for 100-400 kHz I2C. Undersized (too high) pull-ups round rising edges and limit maximum bus speed.
Place 0.1 uF decoupling capacitors at VREF_A and VREF_B pins within 2 mm of the package, and route the eight translated traces as short, direct point-to-point connections. Because the pass-gate is bidirectional, avoid stubs and bus contention: only one driver may be active on a channel at a time.
معلومات الامتثال
RoHS compliance per TI product page. Not AEC-Q100 qualified - use Nexperia LSF0108PW-Q100J for automotive.
