Analog Devices

LT1012DJ8 - Precision Picoamp Op Amp | Analog Devices

MPN: LT1012DJ8 ✓ نشط
Extremely high Vdss Picoampere class Id 8-CDIP, ceramic through-hole DIP Package
الحد الأدنى للطلب: 1 |

LT1012DJ8 نظرة عامة

The Analog Devices LT1012DJ8 is a precision, internally compensated universal operational amplifier designed for low-level instrumentation and measurement applications. The LT1012 family combines picoampere input bias currents, extremely high common-mode rejection, high power-supply rejection, very low warm-up drift, and an offset voltage measured in microvolts. According to the Analog Devices product page, the device can deliver a 5 mA load current with a voltage gain of one million, making it suitable for precision transimpedance, sensor-interface, strain-gauge, and low-level signal-conditioning circuits.

An operational amplifier is a voltage-feedback active component that uses high open-loop gain to amplify small differential signals. The LT1012 belongs to the precision operational amplifier category, a subtype of instrumentation amplifiers and analog signal-chain ICs. Its internally compensated architecture allows use without external frequency-compensation components in voltage-follower and inverting amplifier configurations. The low bias current is particularly valuable when the source impedance is high, because bias-current error at the input contributes directly to output offset.

The LT1012DJ8 is specified for a temperature range of 55°C to 125°C in the LT1012 family description. The DJ8 package is an 8-pin ceramic through-hole DIP package, with a 0.300 inch lead pitch and 7.62 mm body width according to the listed distributor package data. The package designation distinguishes the DJ8 ceramic DIP ordering code from the plastic DIP variants of the same amplifier family.

The device is intended for applications requiring accurate current measurement and low-level voltage amplification. A picoampere-class bias current reduces loading of high-impedance transducers, while the very high common-mode rejection ratio allows small sensor signals to be amplified in the presence of substantial common-mode voltage. The LT1012 can also be used with a gain of one million, although practical board layout, resistor matching, parasitic capacitance, and stability requirements become increasingly important at high closed-loop gains.

Designers should preserve the precision specifications with short, guarded input traces, clean grounding, and symmetrical resistor networks. The manufacturer's LT1012 datasheet should be consulted for the exact offset voltage, input bias current, common-mode range, supply current, maximum input voltage, output swing, and pin configuration before finalizing a circuit. For applications where the ceramic DIP package is unnecessary, the plastic DIP ordering codes provide an alternative construction, but package construction, temperature grade, and lifecycle requirements should be compared before substitution.

بدائل مباشرة لـ LT1012DJ8 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

LT1012DN8

✅ بديل مباشر
📦 8-PDIP (0.300 inch pitch)
Same LT1012 precision-amplifier family and 8-pin through-hole footprint, but plastic 8-PDIP construction replaces the DJ8 ceramic 8-CDIP; package temperature and mechanical qualification must be verified

📋 بديل مرجعي (غير موجود في الكتالوج)

LT1012DJ8

✅ بديل مباشر
Analog Devices
📦 8-CDIP (0.300 inch pitch)
Precision operational amplifier · Analog Devices · Internally compensated universal precision operational amplifier · Picoampere class · Extremely high · Extremely high · Practically unmeasurable · 5 mA

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LT1012DJ8 الحدود القصوى والخصائص الكهربائية

Product Type Precision operational amplifier
Manufacturer Analog Devices
Architecture Internally compensated universal precision operational amplifier
Input Bias Current Picoampere class
Common-Mode Rejection Ratio Extremely high
Power-Supply Rejection Ratio Extremely high
Warm-Up Drift Practically unmeasurable
Load Current 5 mA
Maximum Voltage Gain 1,000,000
نطاق درجة حرارة التشغيل 55°C to 125°C
Package Type 8-CDIP, ceramic through-hole DIP
Package Lead Pitch 0.300 inch (7.62 mm)
عدد الدبابيس 8
نوع التركيب Through-hole
Temperature Grade Commercial

دليل تكوين أطراف LT1012DJ8 0.300 inch (7.62 mm)

تكوين الأطراف لـ LT1012DJ8 (حزمة 0.300 inch (7.62 mm)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 0.300 inch (7.62 mm) لـ LT1012DJ8

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LT1012DJ8.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

LT1012DJ8 مناسب لـ 6 التطبيقs: Precision Transimpedance Amplification, Strain-Gauge Bridge Instrumentation, Low-Level Sensor Signal Conditioning, Battery-Powered Precision Measurement, Precision Current-to-Voltage Conversion, Laboratory Instrumentation and Reference Circuits.

🔬

Precision Transimpedance Amplification

The LT1012DJ8 fits photodiode, photodiode-array, and other high-impedance current-source interfaces where picoampere-class bias current is essential. The low input current minimizes the error introduced across the source impedance, allowing the amplifier to resolve weak current signals without heavy loading. Place the feedback resistor close to the amplifier input and add the compensation capacitance recommended in the LT1012 application guidance to control the parasitic-capacitance-induced stability problem. The family is specified for operation from 55°C to 125°C, making the ceramic DIP suitable for temperature-chambered measurement equipment when its mechanical package is acceptable.

🏭

Strain-Gauge Bridge Instrumentation

The LT1012DJ8 can amplify the small differential output of a strain-gauge or resistive bridge while rejecting common-mode voltage from the bridge excitation. Picoampere-class bias current reduces the burden on the high-impedance bridge output, and the high common-mode rejection ratio helps preserve the bridge signal during common-mode excursions. For a practical design, use matched resistors, shielded sensor wiring, and a single-point ground strategy. The ability to operate at very high gain makes the device useful for bridge signals measured directly without an intermediate instrumentation-amplifier stage.

🧪

Low-Level Sensor Signal Conditioning

The LT1012DJ8 is appropriate for conditioning signals from high-impedance chemical, capacitive, and resistive sensors where conventional CMOS input currents would create unacceptable errors. Its picoampere-class input bias current minimizes sensor loading, while the internally compensated topology supports straightforward voltage-follower and inverting configurations without external compensation networks. The low warm-up drift and high power-supply rejection improve stability in precision laboratory and process-control systems. Verify the exact input offset voltage, common-mode range, and supply limits in the manufacturer datasheet before selecting the operating point.

🔋

Battery-Powered Precision Measurement

The LT1012DJ8 is suited to portable and battery-powered measurement systems because the LT1012 family is designed for precision operation on two Ni-Cad batteries with approximately 1 mW of power dissipation. Low input bias current preserves weak sensor signals, while low-power operation extends the useful operating interval in field instruments. The 8-pin ceramic DIP is mechanically convenient for laboratory and legacy instrumentation equipment, but modern portable products may require a surface-mount implementation. Confirm the exact supply current and battery voltage limits from the LT1012 datasheet before finalizing the power budget.

⚡

Precision Current-to-Voltage Conversion

The LT1012DJ8 can convert small sensor currents into measurable voltages with high accuracy when the feedback network and layout are carefully controlled. Picoampere-class bias current minimizes offset contributions from high-impedance current sources, while the internally compensated amplifier architecture simplifies implementation. The family's capability to support a voltage gain of one million makes it useful for laboratory current measurements where a large conversion ratio is needed. Board cleanliness, guard rings, low-leakage resistors, and short feedback traces are essential for achieving the precision implied by the device's headline specifications.

🖥️

Laboratory Instrumentation and Reference Circuits

The LT1012DJ8 fits precision laboratory instruments that require low offset, very low input current, and high common-mode rejection, including buffer stages, null detectors, and general-purpose precision amplifiers. The 8-pin through-hole DIP construction supports hand-built prototypes and legacy instrument repairs, where ceramic construction may be preferred for temperature stability. A ceramic DIP footprint should be checked against the PCB drill pattern and pin numbering before assembly. Because the device is intended for precision operation, use the manufacturer's offset-null guidance and observe the recommended warm-up period when making null measurements.

ملخص المنتجات الموصى بها

LT1012DN8 Related family member for evaluation in plastic DIP construction يُستخدم في: Precision Transimpedance Amplification, Strain-Gauge Bridge Instrumentation, Low-Level Sensor Signal Conditioning, Battery-Powered Precision Measurement, Precision Current-to-Voltage Conversion, Laboratory Instrumentation and Reference Circuits
What is the LT1012DJ8?
The LT1012DJ8 is an Analog Devices precision, internally compensated universal operational amplifier in an 8-pin ceramic through-hole DIP package. According to the Analog Devices LT1012 product page, the amplifier features picoampere-class input bias currents, extremely high common-mode rejection, high power-supply rejection, very low warm-up drift, and the ability to deliver 5 mA of load current with a voltage gain of one million.
Where can I download the LT1012DJ8 datasheet PDF?
The LT1012DJ8 datasheet is available through the Analog Devices LT1012 product page and the linked LT1012 PDF document. The manufacturer datasheet is the authoritative source for the pin configuration, supply voltage limits, input offset voltage, input bias current, common-mode range, output swing, and recommended application circuits. Use the manufacturer PDF rather than a distributor mirror when checking revision-specific values.
Where can I find the LT1012DJ8 pinout?
The LT1012DJ8 pin assignment is shown in the manufacturer LT1012 datasheet pin-configuration diagram. The DJ8 ordering code is an 8-pin ceramic DIP variant, while other LT1012 ordering codes use different package constructions. Before assigning PCB tracks, verify the exact pin names and offset-null functions against the datasheet because the DJ8 package and the plastic DIP variants must not be assumed to be interchangeable without confirmation.
What is the LT1012DJ8 input bias current?
The LT1012DJ8 uses picoampere-class input bias currents, according to the Analog Devices product description. This low bias current is the key reason the amplifier is useful with high-impedance sources because input bias current produces an error voltage across the source impedance. The exact bias-current value and its temperature coefficient should be taken from the LT1012 datasheet rather than estimated from the product family description.
Can the LT1012DJ8 operate at a voltage gain of one million?
Yes. The Analog Devices LT1012 product page identifies a voltage gain of one million as a capability of the family. In practice, a gain of one million requires very high open-loop gain, extremely accurate feedback resistors, low parasitic capacitance, careful input guarding, and a clean layout to preserve stability and phase margin. Use the manufacturer application guidance when designing such a high-gain stage.
What applications are suitable for the LT1012DJ8?
The LT1012DJ8 is suitable for precision current-to-voltage conversion, strain-gauge and resistance-bridge measurement, high-impedance sensor interfaces, low-level signal conditioning, and instrumentation. Its picoampere-class bias current reduces loading of high-impedance transducers, while high common-mode rejection helps preserve small differential signals in the presence of larger common-mode voltage.
What is the difference between the LT1012DJ8 and LT1012DN8?
The LT1012DJ8 is the ceramic 8-CDIP ordering code, while the LT1012DN8 is the 8-PDIP ordering code listed by DigiKey. Both belong to the LT1012 precision amplifier family, but the package construction, temperature grade, availability, and environmental requirements can differ. Confirm the full datasheet specifications and package qualification before treating one ordering code as a drop-in replacement for the other.
Is the LT1012DJ8 suitable for a transimpedance amplifier?
Yes, the LT1012DJ8 is well suited to precision transimpedance amplification because of its picoampere-class bias current and high common-mode rejection. The feedback resistor and the parasitic capacitance of the photodiode, sensor, board, and input pins determine the achievable bandwidth and stability. Follow the LT1012 application guidance for feedback-component selection and add the recommended compensation capacitance when required.
What is the LT1012DJ8 supply voltage range?
The LT1012DJ8 supply voltage range is not stated in the product-page listing available for this part. Use the manufacturer LT1012 datasheet to confirm the permitted supply voltage for the exact DJ8 ordering code and temperature grade. The supply limits are important because the device is intended for precision operation, and incorrect rail selection can cause input or output saturation.
How does the LT1012DJ8 handle temperature drift?
The Analog Devices product description characterizes the LT1012's warm-up drift as practically unmeasurable. For long-term accuracy, the datasheet's input offset voltage and offset drift specifications should still be reviewed across the intended ambient range and after the required warm-up period. Temperature-stable feedback and reference resistors are also necessary in high-gain instrumentation circuits.
Is the LT1012DJ8 available for purchase?
The LT1012DJ8 is listed for order by authorized distributors, but current stock, volume pricing, and shipment timing can change. Use the Request a Quote form on this page to request current availability, minimum order quantity, and lead time for the exact LT1012DJ8 ordering code. Request the 8-CDIP package variant explicitly if the PCB design requires the ceramic DIP construction.
What is the price of the LT1012DJ8?
The current customer price for the LT1012DJ8 should be requested through the Request a Quote form on this page because distributor pricing depends on quantity, package configuration, and current market availability. The request form can also confirm stock, minimum order quantity, and expected lead time for the exact 8-CDIP ordering code.
How long is the lead time for the LT1012DJ8?
Lead time for the LT1012DJ8 depends on current manufacturer and distributor inventory and should be confirmed for the exact ordering code. Submit the Request a Quote form on this page with your required quantity, target date, and packaging preference. The 8-CDIP package and temperature grade should be confirmed as part of the quotation.
What is the best drop-in replacement for the LT1012DJ8?
The LT1012DN8 is the closest family candidate listed alongside the LT1012DJ8 because it uses an 8-pin through-hole DIP construction, but it is not automatically an equivalent ceramic-DIP replacement. Verify package construction, temperature grade, offset voltage, bias current, supply range, and lifecycle status in the manufacturer datasheet before approving a substitution. No cross-brand drop-in part is identified in the available cross-reference listing.
Is the LT1012DJ8 compliant with RoHS and REACH?
The RoHS and REACH status for the LT1012DJ8 is not stated in the available product-page listing, so the compliance fields are recorded as unknown. Check the current Analog Devices product page, material declaration, or applicable compliance documentation for the exact ordering code. Do not assume compliance from the device's age or from the package construction alone.
What are the key specifications of LT1012DJ8 that engineers should know?
The key LT1012DJ8 characteristics are picoampere-class input bias current, extremely high common-mode rejection, high power-supply rejection, very low warm-up drift, a 5 mA load-current capability, a voltage gain capability of one million, and an 8-pin ceramic through-hole DIP package. The product family operates from 55°C to 125°C according to the Analog Devices description. Confirm exact offset, supply, and output-swing limits in the manufacturer datasheet.
What can replace the LT1012DJ8?
The LT1012DN8 is a related 8-pin through-hole ordering code from the same manufacturer and is the most direct candidate to evaluate, provided that package construction and temperature requirements are acceptable. It should not be described as a confirmed drop-in replacement until the manufacturer datasheet confirms pin compatibility and electrical equivalence. The available cross-reference results do not identify a verified cross-brand drop-in substitute.
Is the LT1012DJ8 the same as an LT1012DN8?
No, the LT1012DJ8 and LT1012DN8 are not the same ordering code. The DJ8 suffix identifies the 8-CDIP ceramic package, whereas the DN8 listing identifies an 8-PDIP package. Their functional family is related, but package construction, temperature grade, and commercial availability can differ, so a footprint substitution requires engineering review.
Can the LT1012DJ8 be used with a Ni-Cad battery supply?
Yes. The Analog Devices product description specifically highlights precision operation on two Ni-Cad batteries with approximately 1 mW of power dissipation. This makes the LT1012DJ8 relevant to low-power battery-powered instrumentation where low bias current, low supply current, and precision signal handling are important.

بيانات مرجعية هندسية لـ LT1012DJ8 — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the LT1012DJ8 when the design requires picoampere-class input bias current, high common-mode and power-supply rejection, low warm-up drift, and an 8-pin ceramic DIP footprint. It is especially appropriate for precision transimpedance amplifiers, strain-gauge bridges, high-impedance sensors, battery-powered laboratory instruments, and legacy equipment that already uses the ceramic-DIP footprint. The LT1012DN8 is the first alternative to evaluate when the electrical family is suitable but the ceramic package construction is not required, provided that temperature grade, supply limits, offset specifications, and lifecycle status are confirmed. Do not select a generic precision op amp on offset voltage alone: the LT1012 family's picoampere-class bias current is the decisive advantage with high-impedance sources. For designs using very high gain, prioritize matched resistors, guarding, compensation, clean PCB assembly, and the manufacturer's recommended layout. If no ceramic DIP is needed and a modern surface-mount part is preferred, the circuit should be re-evaluated rather than treated as a zero-change substitution.

المقارنة مع البدائل

المعامل هذا المنتج LT1012DN8 LT1012DJ8
Package 8-CDIP (0.300 inch pitch) 8-PDIP (0.300 inch pitch) 8-CDIP (0.300 inch pitch)
Brand Analog Devices Analog Devices Analog Devices
Function Precision operational amplifier Precision operational amplifier Precision operational amplifier
Input Bias Current Picoampere class Picoampere class family specification Picoampere class family specification
Common-Mode Rejection Extremely high Extremely high family characteristic Extremely high family characteristic
Power-Supply Rejection Extremely high Extremely high family characteristic Extremely high family characteristic
Load Current 5 mA 5 mA family capability 5 mA family capability
Voltage Gain Capability 1,000,000 1,000,000 family capability 1,000,000 family capability
Temperature Range 55°C to 125°C 55°C to 125°C family description 55°C to 125°C family description
Mounting Style Through-hole ceramic DIP Through-hole plastic DIP Through-hole ceramic DIP

أبرز الفروقات

  • Picoampere-class input bias current supports high-impedance sensing (مقابلLT1012DN8)
  • Very low warm-up drift supports stable precision measurements (مقابلLT1012DN8)
  • Ceramic DIP construction supports legacy precision instrumentation (مقابلLT1012DN8)
  • High-gain capability enables direct precision signal amplification (مقابلLT1012DN8)

ملاحظات التصميم

Keep the LT1012DJ8 input pins, feedback resistor, and optional compensation capacitor physically short and surrounded by a grounded guard where possible. High-impedance input traces act as antennae for leakage and stray capacitance, so a long PCB trace can degrade offset accuracy and stability even when the amplifier itself has picoampere-class bias current. Follow the manufacturer's recommended layout for transimpedance and high-gain configurations.

Do not assume that every LT1012 ordering code has identical package construction. The DJ8 suffix identifies the 8-CDIP ceramic package, while the DN8 listing identifies an 8-PDIP plastic package. Confirm the pin arrangement, package drawing, temperature grade, and supply limits in the manufacturer datasheet before substituting one ordering code for another in an existing PCB design.

Use low-leakage, precision resistors around the input and feedback network, and avoid breadboards or contaminated connectors when the design depends on picoampere-level bias current. Leakage through humidity, flux residue, or PCB contamination can be comparable to the amplifier's bias current. A clean, guarded layout and adequate enclosure venting are important for reproducible measurements in precision laboratory and industrial environments.

The LT1012 family is specifically noted for precision operation on two Ni-Cad batteries at approximately 1 mW power dissipation, making low-power operation an important design advantage. Nevertheless, verify the actual supply-voltage range and quiescent current for the selected ordering code, and provide local bypass capacitance close to the supply pins. Keep supply routing separate from sensitive input and feedback traces.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The available Analog Devices product-page listing does not state RoHS, REACH, halogen-free, lead-free, or conflict-minerals status for the LT1012DJ8. AEC-Q100 is not applicable because this is a precision analog operational amplifier rather than an automotive-qualified device.

تم التحقق من البيانات في: 2026-11-14 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

LT1012DJ8 datasheet LT1012DJ8 pinout LT1012DJ8 datasheet pdf LT1012DJ8 specifications LT1012DJ8 equivalent LT1012DJ8 replacement LT1012DJ8 vs LT1012DN8 Analog Devices LT1012DJ8 LT1012 precision op amp 8-CDIP LT1012DJ8 transimpedance amplifier LT1012DJ8 price LT1012DJ8 stock LT1012DJ8 lead time LT1012DJ8 common mode rejection LT1012DJ8 input bias current

المكونات والمصطلحات ذات الصلة

Analog Devices LT1012 LT1012DJ8 LT1012DN8 precision operational amplifier instrumentation amplifier signal-chain IC picoampere input bias current common-mode rejection ratio power-supply rejection ratio warm-up drift input offset voltage voltage gain transimpedance amplifier strain-gauge bridge high-impedance sensor current-to-voltage conversion Ni-Cad battery 8-CDIP 8-PDIP through-hole package internally compensated Analog Devices product page precision measurement
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر