LT1012DJ8 - Precision Picoamp Op Amp | Analog Devices
MPN: LT1012DJ8 ✓ ActiveLT1012DJ8 Overview
An operational amplifier is a voltage-feedback active component that uses high open-loop gain to amplify small differential signals. The LT1012 belongs to the precision operational amplifier category, a subtype of instrumentation amplifiers and analog signal-chain ICs. Its internally compensated architecture allows use without external frequency-compensation components in voltage-follower and inverting amplifier configurations. The low bias current is particularly valuable when the source impedance is high, because bias-current error at the input contributes directly to output offset.
The LT1012DJ8 is specified for a temperature range of 55°C to 125°C in the LT1012 family description. The DJ8 package is an 8-pin ceramic through-hole DIP package, with a 0.300 inch lead pitch and 7.62 mm body width according to the listed distributor package data. The package designation distinguishes the DJ8 ceramic DIP ordering code from the plastic DIP variants of the same amplifier family.
The device is intended for applications requiring accurate current measurement and low-level voltage amplification. A picoampere-class bias current reduces loading of high-impedance transducers, while the very high common-mode rejection ratio allows small sensor signals to be amplified in the presence of substantial common-mode voltage. The LT1012 can also be used with a gain of one million, although practical board layout, resistor matching, parasitic capacitance, and stability requirements become increasingly important at high closed-loop gains.
Designers should preserve the precision specifications with short, guarded input traces, clean grounding, and symmetrical resistor networks. The manufacturer's LT1012 datasheet should be consulted for the exact offset voltage, input bias current, common-mode range, supply current, maximum input voltage, output swing, and pin configuration before finalizing a circuit. For applications where the ceramic DIP package is unnecessary, the plastic DIP ordering codes provide an alternative construction, but package construction, temperature grade, and lifecycle requirements should be compared before substitution.
Drop-in alternatives for LT1012DJ8 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
LT1012DN8
✅ Drop-In📋 Reference alternative (not in catalog)
LT1012DJ8
✅ Drop-InContact for price
View Datasheet →LT1012DJ8 Maximum Ratings & Electrical Characteristics
| Product Type | Precision operational amplifier |
| Manufacturer | Analog Devices |
| Architecture | Internally compensated universal precision operational amplifier |
| Input Bias Current | Picoampere class |
| Common-Mode Rejection Ratio | Extremely high |
| Power-Supply Rejection Ratio | Extremely high |
| Warm-Up Drift | Practically unmeasurable |
| Load Current | 5 mA |
| Maximum Voltage Gain | 1,000,000 |
| Operating Temperature Range | 55°C to 125°C |
| Package Type | 8-CDIP, ceramic through-hole DIP |
| Package Lead Pitch | 0.300 inch (7.62 mm) |
| Number of Pins | 8 |
| Mounting Type | Through-hole |
| Temperature Grade | Commercial |
LT1012DJ8 0.300 inch (7.62 mm) Pin Configuration Guide
Pin configuration for LT1012DJ8 (0.300 inch (7.62 mm) package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LT1012DJ8.
Refer to the datasheet for full pin configuration.
Typical Applications
LT1012DJ8 is suitable for 6 applications: Precision Transimpedance Amplification, Strain-Gauge Bridge Instrumentation, Low-Level Sensor Signal Conditioning, Battery-Powered Precision Measurement, Precision Current-to-Voltage Conversion, Laboratory Instrumentation and Reference Circuits.
Precision Transimpedance Amplification
The LT1012DJ8 fits photodiode, photodiode-array, and other high-impedance current-source interfaces where picoampere-class bias current is essential. The low input current minimizes the error introduced across the source impedance, allowing the amplifier to resolve weak current signals without heavy loading. Place the feedback resistor close to the amplifier input and add the compensation capacitance recommended in the LT1012 application guidance to control the parasitic-capacitance-induced stability problem. The family is specified for operation from 55°C to 125°C, making the ceramic DIP suitable for temperature-chambered measurement equipment when its mechanical package is acceptable.
Recommended
Strain-Gauge Bridge Instrumentation
The LT1012DJ8 can amplify the small differential output of a strain-gauge or resistive bridge while rejecting common-mode voltage from the bridge excitation. Picoampere-class bias current reduces the burden on the high-impedance bridge output, and the high common-mode rejection ratio helps preserve the bridge signal during common-mode excursions. For a practical design, use matched resistors, shielded sensor wiring, and a single-point ground strategy. The ability to operate at very high gain makes the device useful for bridge signals measured directly without an intermediate instrumentation-amplifier stage.
Recommended
Low-Level Sensor Signal Conditioning
The LT1012DJ8 is appropriate for conditioning signals from high-impedance chemical, capacitive, and resistive sensors where conventional CMOS input currents would create unacceptable errors. Its picoampere-class input bias current minimizes sensor loading, while the internally compensated topology supports straightforward voltage-follower and inverting configurations without external compensation networks. The low warm-up drift and high power-supply rejection improve stability in precision laboratory and process-control systems. Verify the exact input offset voltage, common-mode range, and supply limits in the manufacturer datasheet before selecting the operating point.
Recommended
Battery-Powered Precision Measurement
The LT1012DJ8 is suited to portable and battery-powered measurement systems because the LT1012 family is designed for precision operation on two Ni-Cad batteries with approximately 1 mW of power dissipation. Low input bias current preserves weak sensor signals, while low-power operation extends the useful operating interval in field instruments. The 8-pin ceramic DIP is mechanically convenient for laboratory and legacy instrumentation equipment, but modern portable products may require a surface-mount implementation. Confirm the exact supply current and battery voltage limits from the LT1012 datasheet before finalizing the power budget.
Recommended
Precision Current-to-Voltage Conversion
The LT1012DJ8 can convert small sensor currents into measurable voltages with high accuracy when the feedback network and layout are carefully controlled. Picoampere-class bias current minimizes offset contributions from high-impedance current sources, while the internally compensated amplifier architecture simplifies implementation. The family's capability to support a voltage gain of one million makes it useful for laboratory current measurements where a large conversion ratio is needed. Board cleanliness, guard rings, low-leakage resistors, and short feedback traces are essential for achieving the precision implied by the device's headline specifications.
Recommended
Laboratory Instrumentation and Reference Circuits
The LT1012DJ8 fits precision laboratory instruments that require low offset, very low input current, and high common-mode rejection, including buffer stages, null detectors, and general-purpose precision amplifiers. The 8-pin through-hole DIP construction supports hand-built prototypes and legacy instrument repairs, where ceramic construction may be preferred for temperature stability. A ceramic DIP footprint should be checked against the PCB drill pattern and pin numbering before assembly. Because the device is intended for precision operation, use the manufacturer's offset-null guidance and observe the recommended warm-up period when making null measurements.
Recommended
Recommended Products Summary
Engineering reference data for LT1012DJ8 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LT1012DN8 | LT1012DJ8 |
|---|---|---|---|
| Package | 8-CDIP (0.300 inch pitch) | 8-PDIP (0.300 inch pitch) | 8-CDIP (0.300 inch pitch) |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Function | Precision operational amplifier | Precision operational amplifier | Precision operational amplifier |
| Input Bias Current | Picoampere class | Picoampere class family specification | Picoampere class family specification |
| Common-Mode Rejection | Extremely high | Extremely high family characteristic | Extremely high family characteristic |
| Power-Supply Rejection | Extremely high | Extremely high family characteristic | Extremely high family characteristic |
| Load Current | 5 mA | 5 mA family capability | 5 mA family capability |
| Voltage Gain Capability | 1,000,000 | 1,000,000 family capability | 1,000,000 family capability |
| Temperature Range | 55°C to 125°C | 55°C to 125°C family description | 55°C to 125°C family description |
| Mounting Style | Through-hole ceramic DIP | Through-hole plastic DIP | Through-hole ceramic DIP |
Key Differentiators
- Picoampere-class input bias current supports high-impedance sensing (vs LT1012DN8)
- Very low warm-up drift supports stable precision measurements (vs LT1012DN8)
- Ceramic DIP construction supports legacy precision instrumentation (vs LT1012DN8)
- High-gain capability enables direct precision signal amplification (vs LT1012DN8)
Design Notes
Keep the LT1012DJ8 input pins, feedback resistor, and optional compensation capacitor physically short and surrounded by a grounded guard where possible. High-impedance input traces act as antennae for leakage and stray capacitance, so a long PCB trace can degrade offset accuracy and stability even when the amplifier itself has picoampere-class bias current. Follow the manufacturer's recommended layout for transimpedance and high-gain configurations.
Do not assume that every LT1012 ordering code has identical package construction. The DJ8 suffix identifies the 8-CDIP ceramic package, while the DN8 listing identifies an 8-PDIP plastic package. Confirm the pin arrangement, package drawing, temperature grade, and supply limits in the manufacturer datasheet before substituting one ordering code for another in an existing PCB design.
Use low-leakage, precision resistors around the input and feedback network, and avoid breadboards or contaminated connectors when the design depends on picoampere-level bias current. Leakage through humidity, flux residue, or PCB contamination can be comparable to the amplifier's bias current. A clean, guarded layout and adequate enclosure venting are important for reproducible measurements in precision laboratory and industrial environments.
The LT1012 family is specifically noted for precision operation on two Ni-Cad batteries at approximately 1 mW power dissipation, making low-power operation an important design advantage. Nevertheless, verify the actual supply-voltage range and quiescent current for the selected ordering code, and provide local bypass capacitance close to the supply pins. Keep supply routing separate from sensitive input and feedback traces.
Compliance Information
The available Analog Devices product-page listing does not state RoHS, REACH, halogen-free, lead-free, or conflict-minerals status for the LT1012DJ8. AEC-Q100 is not applicable because this is a precision analog operational amplifier rather than an automotive-qualified device.