LT1807IS8 - 325MHz Dual Rail-to-Rail Op Amp | Analog Devices
MPN: LT1807IS8 ✓ نشطLT1807IS8 نظرة عامة
An operational amplifier is a voltage-gain amplifier used to amplify, filter, buffer, or compare analog signals. The LT1807 belongs to the precision amplifier hierarchy within the broader amplifier IC and analog signal-processing categories. Rail-to-rail input capability increases the usable input range, while rail-to-rail output capability allows the output voltage to approach the supply rails under suitable load conditions.
The LT1807IS8 combines 325 MHz gain-bandwidth product with a 140 V/µs slew rate, enabling accurate response to rapidly changing signals. Both channels offer low-noise, low-distortion operation and unity-gain stability. An 85 mA output-current capability supports wider-range signal driving than a conventional low-power precision amplifier, although the external load, supply voltage, and thermal conditions still determine achievable swing.
The dual architecture integrates two independent amplifiers into one package, reducing component count in designs requiring parallel signal paths. Standard dual-op-amp pinout compatibility simplifies board construction when an existing SO-8 footprint follows the same pin assignments. The device is optimized for low-voltage, high-performance signal chains where bandwidth, slew rate, input range, and output range are important simultaneously.
Typical uses include video-signal conditioning, communications-interface amplification, data acquisition, industrial instrumentation, and active filtering. The LT1807 can also serve in low-voltage control systems, test equipment, and sensor interfaces where a fast amplifier must accept input signals near either supply rail and drive downstream circuitry with low distortion.
When using the LT1807IS8, verify the intended supply voltage, output-load current, input common-mode range, and output-swing limits against the operating conditions in the manufacturer datasheet. Place input and output decoupling capacitors close to the device, preserve the required feedback-network layout, and avoid excessive capacitive loading on the outputs because stability and transient response can depend on the load.
This page combines the LT1807IS8's principal performance characteristics, ordering alternatives, comparison data, and practical circuit guidance. It is designed to help engineers identify the correct SO-8 amplifier, assess family options, and plan robust high-speed analog layouts.
بدائل مباشرة لـ LT1807IS8 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
LT1807IS8#PBF
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LT1807IS8#TRPBF
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LT1807IS8#TR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LT1807CS8#PBF
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LT1807CS8#TR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LT1807IS8 الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual precision operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 325 MHz |
| Slew Rate | 140 V/µs |
| Output Current | 85 mA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Gain Stability | Unity-gain stable |
| Noise Performance | Low noise |
| Distortion | Low distortion |
| العلبة | 8-pin SO package |
| نوع التركيب | Surface mount |
تكوين أطراف LT1807IS8
| دبوس 1 | OUTA — Amplifier A output |
| دبوس 2 | -INA — Inverting input for amplifier A |
| دبوس 3 | +INA — Non-inverting input for amplifier A |
| دبوس 4 | V- — Negative supply connection |
| دبوس 5 | +INB — Non-inverting input for amplifier B |
| دبوس 6 | -INB — Inverting input for amplifier B |
| دبوس 7 | OUTB — Amplifier B output |
| دبوس 8 | V+ — Positive supply connection |
التطبيقات النموذجية
LT1807IS8 مناسب لـ 6 التطبيقs: High-Speed Video Signal Conditioning, Communications Interface Amplification, Precision Data Acquisition Front End, Industrial Sensor Signal Amplification, Active Audio and Low-Distortion Filters, Test and Measurement Buffering.
High-Speed Video Signal Conditioning
The LT1807IS8 is suitable for video buffers and gain stages because its 325 MHz gain-bandwidth product and 140 V/µs slew rate preserve signal timing and amplitude through moderate-gain paths. Rail-to-rail input and output operation provides useful range in low-voltage analog systems, while unity-gain stability allows direct follower use. Each channel can process an independent signal, reducing the number of packages in dual-channel conditioning circuits. Designers should terminate inputs according to the source impedance, preserve short feedback paths, and verify output swing and capacitive-load behavior for the selected video standard.
موصى به
Communications Interface Amplification
The LT1807IS8 fits low-voltage communications interfaces that require two fast, low-noise amplification paths. Its 325 MHz gain-bandwidth product supports broad signal bandwidth, and the 140 V/µs slew rate helps preserve edge information when signals change rapidly. The dual configuration can handle two channels with the same package pinout. Rail-to-rail inputs are useful near supply limits, but the designer must confirm common-mode limits, output swing, noise, and drive capability for the specific line rate and termination network.
موصى به
Precision Data Acquisition Front End
The LT1807IS8 can serve as a fast input buffer or gain stage ahead of high-resolution data-conversion circuitry. Its low-noise, low-distortion characteristics support accurate handling of sensor and instrumentation signals, while the 325 MHz bandwidth and 140 V/µs slew rate provide margin for rapid transients. Rail-to-rail inputs increase sensitivity to signals near either supply rail. Keep the source impedance and feedback resistors in mind, provide local supply bypassing, and verify settling performance against the acquisition bandwidth and sensor output bandwidth.
موصى به
Industrial Sensor Signal Amplification
The LT1807IS8 is appropriate for conditioning outputs from fast industrial sensors when low-voltage headroom and signal speed are important. Rail-to-rail input operation helps accept sensor signals near the supply range, and the dual architecture supports differential or dual-ended channels. The 85 mA output-current capability provides more drive margin than a low-current precision amplifier, but load-dependent swing and distortion must be checked. Use short traces, local decoupling, and an output protection network when connecting to long cables or high-capacitance inputs.
موصى به
Active Audio and Low-Distortion Filters
The LT1807IS8 can implement active filters or low-distortion buffers in audio and instrumentation signal chains. Its 325 MHz gain-bandwidth product allows a wide operating range for precision filter sections, while unity-gain stability supports stable buffering. Low-noise and low-distortion behavior helps preserve small signals, and the two amplifier channels permit a cascaded filter or paired processing paths. Select resistor and capacitor values that keep the closed-loop noise gain within the stable operating region, and verify output swing at the intended signal amplitude and load.
موصى به
Test and Measurement Buffering
The LT1807IS8 is useful in test and measurement front ends that must buffer sensor, probe, or source signals without excessive bandwidth or slew limitations. The 325 MHz gain-bandwidth product and 140 V/µs slew rate support wideband measurements, while the dual package provides two independent channels in one footprint. Unity-gain stability makes follower configuration straightforward. For accurate results, account for input bias current, offset, noise, output loading, and the measurement bandwidth, and use a clean, well-decoupled supply to avoid converter artifacts entering the analog path.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LT1807IS8 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LT1807IS8#PBF | LT1807IS8#TRPBF | LT1807IS8#TR | LT1807CS8#PBF | LT1807CS8#TR |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SO package | 8-pin SO package | 8-pin SO package | 8-pin SO package | 8-pin SO package | 8-pin SO package |
| Amplifier Configuration | Dual amplifier | Dual amplifier | Dual amplifier | Dual amplifier | Dual amplifier | Dual amplifier |
| Gain-Bandwidth Product | 325 MHz | 325 MHz | 325 MHz | 325 MHz | 325 MHz | 325 MHz |
| Slew Rate | 140 V/µs | 140 V/µs | 140 V/µs | 140 V/µs | 140 V/µs | 140 V/µs |
| Output Current | 85 mA | 85 mA | 85 mA | 85 mA | 85 mA | 85 mA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Gain Stability | Unity-gain stable | Unity-gain stable | Unity-gain stable | Unity-gain stable | Unity-gain stable | Unity-gain stable |
أبرز الفروقات
- Combines high speed with rail-to-rail signal handling (مقابلLT1807IS8#PBF)
- Dual precision channels in a standard SO-8 footprint (مقابلLT1807CS8#PBF)
- Unity-gain-stable operation supports direct buffering (مقابلLT1807IS8#TRPBF)
ملاحظات التصميم
Keep both supply bypass connections short and place the capacitors immediately across the LT1807 supply pins and ground plane. Maintain a compact feedback loop around each amplifier, with feedback resistors and load components located close to the relevant output and inverting-input pins. The 140 V/µs slew rate makes parasitic inductance and long traces more significant than they would be in a slow precision amplifier.
Do not assume that rail-to-rail input and output ratings permit operation exactly at either supply rail under every condition. Check the datasheet limits for input common-mode range, output swing, load current, and supply voltage. Also verify capacitive loading before driving long cables or ADC sample-and-hold inputs, because excessive output capacitance can affect transient response and stability.
Choose feedback and gain-setting resistors with values that preserve the intended signal bandwidth while limiting amplifier-generated noise and parasitic capacitance. For high-gain stages, evaluate noise gain and stability across the complete frequency range rather than only at the nominal signal frequency. Source impedances should also be compared with the input-bias-current and bias-current cancellation requirements.
معلومات الامتثال
Compliance status was not identified in the manufacturer or distributor information for the exact LT1807IS8 ordering code.