LT1991HMS - 100uA Gain-Selectable Amplifier | Analog Devices
MPN: LT1991HMS ✓ نشطLT1991HMS نظرة عامة
A programmable or gain-selectable amplifier is an analog signal-conditioning device that adjusts the relationship between an input voltage and an output voltage using an internal precision resistor network. The LT1991 belongs to the operational-amplifier family and sits within the broader hierarchy of amplifiers, analog ICs, and signal-conditioning semiconductors. Its internal resistor matching is particularly useful for difference-amplifier and differential-measurement circuits where common-mode rejection and gain accuracy are important.
The LT1991HMS features a maximum input offset voltage of 50uV and a gain-bandwidth product of 560kHz. It draws only 100uA of supply current on a 5V supply, making it suitable for battery-operated instruments and low-leakage measurement systems. The output can swing to within 40mV of either supply rail, providing useful headroom for single-supply and dual-supply signal chains. The device is supplied in an MSOP-10 package with an operating temperature range of -40C to +125C.
The internal precision-resistor architecture eliminates the external resistor ratios normally required to establish accurate amplifier gains. This reduces component count, resistor-matching error, and board-space requirements in measurement front ends. The amplifier's low supply current is valuable when the input source itself has limited drive capability, while the wide supply range supports industrial, instrumentation, and process-control systems. Its 560kHz gain-bandwidth product is adequate for low- to moderate-frequency precision signal conditioning rather than high-speed waveform processing.
Typical applications include differential sensor measurement, current-shunt monitoring, low-power laboratory instrumentation, portable measurement equipment, gain-programmed analog front ends, and industrial control circuits. The LT1991 is particularly well suited to difference-amplifier use because the matched internal resistors improve common-mode rejection when both inputs are close in voltage.
For a new design, verify the selected gain code, input common-mode range, output swing, and bias-current requirements against the pin description table in the manufacturer datasheet. Place the device close to the signal source, use a clean low-noise supply, and account for input bias-current errors when the source impedance is high. The MSOP-10 footprint requires careful decoupling and thermal-layout review for sustained operation at the upper end of the temperature range.
بدائل مباشرة لـ LT1991HMS — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
LT1991HMS-PBF
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LT1991HMS الحدود القصوى والخصائص الكهربائية
| Product Type | Gain-selectable precision amplifier |
| Architecture | Operational amplifier with eight internal precision resistors |
| Gain Range | -13 to +14 |
| Gain Accuracy | 0.04% |
| Maximum Input Offset Voltage | 50 uV |
| Gain-Bandwidth Product | 560 kHz |
| Supply Voltage Range | 2.7 V to 36 V |
| تيار التغذية | 100 uA at 5 V supply |
| Output Swing | Within 40 mV of either supply rail |
| Common-Mode Rejection | 100 dB |
| Slew Rate | 0.1200 V/us |
| Input Bias Current | 0.0150 uA |
| نطاق درجة حرارة التشغيل | -40C to +125C |
| العلبة | MSOP-10, plastic |
| Terminal Count | 10 |
| نوع التركيب | Surface mount |
دليل تكوين أطراف LT1991HMS msop-10, plastic
تكوين الأطراف لـ LT1991HMS (حزمة msop-10, plastic). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LT1991HMS.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LT1991HMS مناسب لـ 6 التطبيقs: Precision Difference Amplification, Current-Shunt Monitoring, Portable Instrument Signal Conditioning, Industrial Sensor Interface, Low-Power Process-Control Front End, Low-Frequency Analog Measurement.
Precision Difference Amplification
The LT1991HMS is well suited to differential measurement because its eight internal precision resistors provide selectable gains from -13 to +14 with 0.04% gain accuracy. Place it in a difference-amplifier configuration when two nearby voltages must be amplified while suppressing common-mode error. The 100dB common-mode rejection specification supports accurate measurements of small differential signals, while 100uA supply current at 5V helps maintain low power consumption. Check the selected gain code and input common-mode limits in the manufacturer datasheet before finalizing the layout.
موصى به
Current-Shunt Monitoring
Use the LT1991HMS to amplify the small voltage generated by a current shunt in battery systems, power converters, and motor-control circuits. The 50uV maximum input offset voltage helps preserve measurement accuracy with low-amplitude shunt signals, while the internal resistor network removes the need for an external gain resistor pair. The 560kHz gain-bandwidth product is suitable for slowly changing or moderate-bandwidth current measurements rather than high-frequency pulse monitoring. Use Kelvin routing and verify input bias-current errors for high-resistance sense paths.
موصى به
Portable Instrument Signal Conditioning
The LT1991HMS fits portable measurement instruments where every milliamp of supply current and every external component affects battery life or board area. Its 100uA supply current at 5V supports low-power operation, while the internal precision resistors provide a selectable gain range from -13 to +14 without external gain-setting resistors. The 2.7V to 36V supply range also allows the same device family to be used across low-voltage and higher-voltage instrument architectures. Select the gain code and bypass capacitor placement according to the manufacturer application guidance.
موصى به
Industrial Sensor Interface
The LT1991HMS can condition low-level industrial sensor signals when accurate scaling and low power are more important than high bandwidth. The 0.04% gain accuracy of the internal resistor network improves scale-factor repeatability, and the 100dB common-mode rejection helps reject unwanted voltage common to both inputs. The device accepts supplies from 2.7V to 36V, making it adaptable to multiple industrial signal-chain supply plans. Confirm the sensor's output range, common-mode limits, and grounding arrangement before using the amplifier near high-energy equipment.
موصى به
Low-Power Process-Control Front End
For low-power process-control modules, the LT1991HMS provides a compact way to scale small analog inputs with limited external circuitry. Its integrated precision resistor network supports stable gain without hand-matched external components, and the 100uA supply current at 5V helps limit standby consumption. The wide 2.7V to 36V operating range supports shared supply rails in mixed-signal equipment. Keep the input path short, provide local supply bypassing, and verify that the selected gain remains within the amplifier's output-swing limits.
موصى به
Low-Frequency Analog Measurement
The LT1991HMS is appropriate for low-frequency analog measurement systems that need precise gain selection rather than high closed-loop speed. Its 560kHz gain-bandwidth product supports measurement and control bandwidths below the amplifier's high-frequency limit, while the 50uV maximum input offset voltage helps reduce signal-path error. Use it ahead of an ADC or control input when the signal source can drive the amplifier's bias current. For applications requiring wider bandwidth, more output drive, or adjustable external gain, compare a dedicated precision op amp instead.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LT1991HMS — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LT1991HMS-PBF |
|---|---|---|
| Package | MSOP-10 | MSOP-10 |
| Brand | Analog Devices | Analog Devices |
| Product Type | Gain-selectable precision amplifier | Gain-selectable precision amplifier |
| Supply Voltage Range | 2.7 V to 36 V | 2.7 V to 36 V |
| Supply Current | 100 uA at 5 V supply | 100 uA at 5 V supply |
| Gain Range | -13 to +14 | -13 to +14 |
| Gain Accuracy | 0.04% | 0.04% |
| Gain-Bandwidth Product | 560 kHz | 560 kHz |
| Maximum Input Offset Voltage | 50 uV | 50 uV |
| Operating Temperature Range | -40C to +125C | -40C to +125C |
أبرز الفروقات
- Integrated precision gain network (مقابلGeneral-purpose external-resistor amplifier)
- Very low supply current (مقابلGeneral-purpose precision op amp)
- Difference-amplifier optimization (مقابلDiscrete resistor difference amplifier)
ملاحظات التصميم
Place the LT1991HMS close to the signal source and keep input traces short to minimize susceptibility to noise and input-bias-current errors. Route the inputs as a closely matched pair when the device is used as a difference amplifier. Place the supply bypass capacitor near the power pin and maintain a compact return path to the ground reference.
Do not assume that any close signal gain is available. The LT1991 uses selectable internal resistors and supports gains from -13 to +14, so verify the gain table in the manufacturer datasheet. Also check that the input common-mode voltage and the required output level remain inside the device limits, especially with a 2.7V supply.
The stated 100uA supply current is specified at a 5V supply, so it should not be treated as a constant over the entire 2.7V to 36V range. Calculate the actual supply power for the selected operating point and use the lowest supply voltage that still provides adequate input and output headroom. Add local decoupling and verify the regulator's transient behavior.
For high-impedance sources, evaluate the input-bias-current contribution. The listed input bias current is 0.0150uA, which can create an error across a large source impedance even when the amplifier's 50uV offset specification is acceptable. Use a lower-impedance source, account for input capacitance, or choose a different amplifier when the source is extremely high impedance.
معلومات الامتثال
The available product listings identify LT1991HMS and LT1991HMS-PBF but do not explicitly state the requested compliance attributes. The PBF ordering notation should not be treated as independent proof of lead-free or halogen-free status without the manufacturer declaration.