LTC7652CH Zero-Drift Op Amp, 5uV Offset | Analog Devices
MPN: LTC7652CH ✗ انتهى عمره الإنتاجيLTC7652CH نظرة عامة
A zero-drift operational amplifier is an amplifier architecture that continuously corrects offset-voltage errors instead of allowing input-referred offsets to drift with time, temperature, or common-mode voltage. Within the broader hierarchy of amplifier ICs and instrumentation signal-conditioning devices, the LTC7652CH trades higher-frequency simplicity for exceptionally low DC offset and drift. Its picoampere input current also makes it suitable for high-impedance transducers.
The principal benefit of the LTC7652CH is its combination of low offset and low drift. The maximum offset is 5uV, the maximum offset drift is 0.05uV/°C, and the typical offset drift is 0.01uV/°C. Long-term stability is specified at 100nV/month. These characteristics improve DC measurement accuracy when small differential signals must be amplified without substantial error from the amplifier itself.
Chopper stabilization constantly corrects errors associated with initial offset and changes in offset caused by time, temperature, and common-mode voltage. The manufacturer describes both the LTC7652 and LTC1052 as low-noise zero-drift amplifiers built with enhanced LTCMOS silicon-gate technology. The 30pA guaranteed maximum input bias current supports leakage-sensitive measurement paths, while the 4V/us nominal slew rate provides useful bandwidth for moderate-amplitude transient signals.
Typical applications include precision bridge-amplifier front ends, low-level current measurement, temperature-sensor conditioning, strain-gage instrumentation, low-voltage error amplifiers, and laboratory sensor interfaces. The low offset is particularly valuable when the measured signal is near the millivolt or microvolt scale, while the low input bias current reduces loading on high-impedance sensors.
For best results, use stable reference and feedback resistors, keep input and output layouts compact, and account for the power-supply range and common-mode limits in the manufacturer datasheet. The LTC7652CH is an older hermetic TO-5 device, so designers should verify availability, temperature coverage, lead finish, and procurement requirements before committing a new production design to this package.
This page combines the LTC7652CH offset, drift, bias-current, package, and slew-rate characteristics with purchasing guidance, selection considerations, and engineering guidance for zero-drift amplifier design. It also distinguishes exact drop-in options from broader functional equivalents so engineers can assess PCB compatibility before making a replacement decision.
بدائل مباشرة لـ LTC7652CH — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
LTC7652
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
LTC7652C
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
LTC7652CH الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Zero-drift operational amplifier |
| Circuit Count | 1 circuit |
| Guaranteed Maximum Offset Voltage | 5uV |
| Guaranteed Maximum Offset Drift | 0.05uV/°C |
| Typical Offset Drift | 0.01uV/°C |
| Long-Term Offset Stability | 100nV/month |
| Guaranteed Maximum Input Bias Current | 30pA |
| Nominal Slew Rate | 4V/us |
| Stabilization Method | Chopper stabilization |
| Semiconductor Process | Enhanced LTCMOS silicon-gate process |
| Input Current Class | Picoampere input current |
| Temperature Grade | Industrial |
| Package Type | 8-terminal round TO-5 |
| Terminal Form | Wire |
| نمط التركيب | Through-hole metal can |
| Input Offset Correction | Time, temperature, and common-mode voltage correction |
دليل تكوين أطراف LTC7652CH 8-terminal round to-5
تكوين الأطراف لـ LTC7652CH (حزمة 8-terminal round to-5). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LTC7652CH.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LTC7652CH مناسب لـ 6 التطبيقs: Precision Bridge Amplifier, Low-Level Current Sensing, Temperature Sensor Conditioning, Strain-Gage Instrumentation, High-Impedance Transducer Interface, Laboratory Instrumentation.
Precision Bridge Amplifier
The LTC7652CH suits precision bridge-amplifier front ends where a small differential sensor signal is superimposed on a larger common-mode level. Its guaranteed 5uV maximum input offset limits amplifier-generated error, while the 30pA maximum input bias current reduces loading on high-impedance bridge outputs. Chopper stabilization corrects offset changes associated with time, temperature, and common-mode voltage, improving long-term DC accuracy. In a typical instrumentation circuit, the amplifier multiplies the bridge imbalance while rejecting common-mode voltage; engineers should still verify input common-mode range, output swing, supply voltage, resistor matching, and gain stability against the manufacturer datasheet before finalizing the front end.
موصى به
Low-Level Current Sensing
The LTC7652CH is appropriate for low-level current measurement when the shunt voltage approaches the millivolt range and amplifier offset would otherwise become a significant error source. Its guaranteed 5uV maximum offset and 0.05uV/°C maximum drift help maintain accuracy across temperature changes, while the 4V/us nominal slew rate supports moderate signal transitions. Place the amplifier in a differential configuration around the shunt and pay attention to input bias-current offsets, resistor-generated errors, common-mode limits, and output saturation. The very low 30pA maximum bias current is valuable when the shunt is implemented as a high-value resistor or when measurement-node leakage could otherwise create a comparable error.
موصى به
Temperature Sensor Conditioning
The LTC7652CH can condition resistive temperature-detector signals where accurate DC amplification is more important than wide-bandwidth performance. The 5uV guaranteed maximum offset is small relative to many millivolt-scale RTD signals, and the 30pA maximum input bias current reduces excitation-dependent loading on high-value sensing elements. Chopper stabilization reduces offset movement caused by temperature and elapsed time, which benefits stable industrial readings. A practical circuit uses the amplifier with an excitation reference and matched feedback network, then converts the amplified differential voltage through an ADC. Verify supply voltage, input common-mode range, output swing, noise behavior, and the sensor's excitation level in the manufacturer datasheet before selecting resistor values.
موصى به
Strain-Gage Instrumentation
The LTC7652CH matches strain-gage instrumentation requirements because strain signals are small and the bridge's common-mode voltage can be much larger than the desired measurement. With a guaranteed 5uV maximum offset and 0.05uV/°C maximum drift, the amplifier limits input-referred DC error, while picoampere-level input bias current avoids appreciably loading the bridge. Its chopper-stabilized architecture corrects initial offset and drift caused by temperature, time, and common-mode changes. Use a balanced bridge and low-noise gain network, and observe the manufacturer's input and output range limits. Thermal gradients across the amplifier and unequal bridge resistors can create errors larger than the amplifier offset, so placement and resistor selection remain important.
موصى به
High-Impedance Transducer Interface
The LTC7652CH is useful for interfaces involving high-source-impedance transducers because its guaranteed maximum input bias current is only 30pA. That low current minimizes the error voltage produced across a sensitive source and allows the amplifier to preserve small sensor signals. The 5uV maximum offset and chopper-based correction of time-, temperature-, and common-mode-dependent drift support stable DC measurements. Designers commonly place the LTC7652CH near the transducer to minimize parasitic leakage and routing capacitance, then use guarded grounding or shielding where necessary. Confirm dielectric absorption, board cleanliness, humidity effects, and input protection requirements at the system level, because these factors can dominate the total measurement error.
موصى به
Laboratory Instrumentation
The LTC7652CH can serve as the input amplifier in laboratory instruments that measure microvolt-level or millivolt-level DC signals with stable references. Its 5uV maximum offset, 0.01uV/°C typical drift, and 100nV/month long-term stability reduce time-dependent calibration shifts. Chopper stabilization continuously corrects offset errors, while the 30pA maximum bias current helps when source impedances are high. The 4V/us nominal slew rate is sufficient for many low-frequency measurement signals but does not make the device a general-purpose wideband amplifier. Validate noise density, clock-related artifacts, settling behavior, input capacitance, and EMI pickup in the final instrument, and use the manufacturer datasheet for the complete test conditions.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LTC7652CH — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LTC7652 | LTC7652C |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-terminal round TO-5 | 8-terminal round TO-5 | 8-terminal round TO-5 |
| Amplifier Type | Chopper-stabilized zero-drift operational amplifier | Chopper-stabilized zero-drift operational amplifier | Chopper-stabilized zero-drift operational amplifier |
| Guaranteed Maximum Offset | 5uV | 5uV | 5uV |
| Guaranteed Maximum Offset Drift | 0.05uV/°C | 0.05uV/°C | 0.05uV/°C |
| Typical Offset Drift | 0.01uV/°C | 0.01uV/°C | 0.01uV/°C |
| Maximum Input Bias Current | 30pA | 30pA | 30pA |
| Nominal Slew Rate | 4V/us | 4V/us | 4V/us |
| Long-Term Stability | 100nV/month | 100nV/month | 100nV/month |
أبرز الفروقات
- Guaranteed maximum offset (مقابلLTC7652)
- Ultra-low input bias current (مقابلLTC7652C)
- Low offset drift with chopper correction (مقابلLTC7652)
ملاحظات التصميم
Do not treat every LTC7652 family member as automatically interchangeable. Before replacing LTC7652CH, compare the manufacturer ordering table for terminal assignments, temperature grade, supply voltage, common-mode range, output swing, offset limits, drift limits, and package lead finish. The visible product information confirms an industrial-grade, 8-terminal TO-5 device but does not provide enough detail to certify every suffix combination as a true drop-in part.
Place the LTC7652CH close to the source and feedback components, and keep input traces short to reduce leakage, thermoelectric-voltage pickup, and susceptibility to electromagnetic interference. Because offset error can be only 5uV, copper temperature gradients and dirty or humid board surfaces may create meaningful error. Use a low-leakage PCB finish, guard sensitive input nodes where appropriate, and maintain stable reference resistors to prevent board-level drift from overwhelming the amplifier's own drift specification.
Chopper stabilization corrects low-frequency offset but introduces periodic switching-related artifacts that can matter in high-resolution measurements. Evaluate the complete signal chain rather than relying only on the 5uV maximum offset rating. Use the manufacturer datasheet and application guidance to determine chopping-frequency effects, filtering requirements, settling behavior, and input capacitance limits. Apply appropriate low-pass filtering after confirming that its bandwidth preserves the intended measurement bandwidth.
معلومات الامتثال
The visible product information identifies an industrial temperature grade but does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status. Confirm current declarations with Analog Devices before production release.