M30624FGPFP#U5C - M16C/62P 16-bit MCU, 256KB Flash, 100-QFP | Renesas
MPN: M30624FGPFP#U5C ✗ انتهى عمره الإنتاجيM30624FGPFP#U5C نظرة عامة
A microcontroller (MCU) is an integrated circuit that combines a CPU, memory (RAM/ROM/Flash), and programmable I/O peripherals on a single silicon die. The M16C family sits within the 16-bit microcontroller taxonomy, between 8-bit MCUs (e.g., 8051) and 32-bit ARM Cortex-M devices, offering a balance of code density, deterministic interrupt latency, and peripheral integration well suited to real-time control. The M16C/62P Group sits under the M16C/60 Series umbrella of Renesas's mid-range MCU portfolio.
Key features include 256 KB of on-chip flash (256K x 8), 4 KB of on-chip RAM, a 24 MHz maximum CPU clock, a 10-bit A/D converter, a wide operating voltage range of 2.7V to 5.5V, and an operating temperature range of -20C to +85C. The 100-QFP package provides ample I/O for motor control, automotive body electronics, and industrial automation. Multiple timers, serial interfaces (UART, I2C, SPI), and interrupt controllers are integrated, eliminating the need for external peripherals.
The M16C/60 CPU core uses a register-based architecture with 24-bit linear addressing, supporting high-level language efficiency and rich addressing modes. Built-in flash allows in-application reprogramming via serial or background programming modes, simplifying field firmware updates. The silicon-gate CMOS process yields low quiescent current and supports 3V and 5V system designs with a single part number.
Typical applications include industrial motor control, HVAC control boards, automotive body ECUs, home appliance controllers (washing machines, microwave ovens), and metering/pump controllers. The wide 2.7V-5.5V supply range makes it suitable for both 3.3V and 5V logic designs.
When designing with this MCU, ensure the 100-pin QFP footprint matches your PCB land pattern and provide adequate decoupling (100 nF + 10 uF) near each power pin. Use the on-chip debug/flash programming interface for production firmware loading rather than relying on external programmers. Note that Renesas recommends the newer M3062LFGPFP for new designs.
This page consolidates distributor pricing, drop-in alternative analysis, and practical design notes beyond what the manufacturer datasheet alone provides.
بدائل مباشرة لـ M30624FGPFP#U5C — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع M30624FGPFP#U5C (نفس عامل الشكل والبصمة) — يختلف في Series, Package, A/D Converter, Operating Temperature, Supply Voltage.
M3062LFGPFP
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
M3062LFGPFP#U5C
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
M30624FGPGP
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
M30624FGPGP#U5C
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
M30626FJPFP#U5C
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
M30624FGPFP#U5C الحدود القصوى والخصائص الكهربائية
| Series | M16C/60 M16C/62P Group |
| Core | M16C/60 16-bit CPU |
| Program Memory | 256 KB (256K x 8) FLASH |
| RAM | 4 KB |
| Maximum CPU Clock | 24 MHz |
| عرض ناقل البيانات | 16-bit |
| Operating Voltage | 2.7 V to 5.5 V |
| درجة حرارة التشغيل | -20 C to +85 C |
| A/D Converter | 10-bit |
| العلبة | 100-QFP (14 x 20 mm) |
| نوع التركيب | Surface Mount |
| نمط التركيب | SMT |
| Lead-Free | Pb-free (per #U5C suffix) |
| I/O Pins | 85 (per JLCPCB attribute) |
| ECCN | EAR99 |
| RoHS | Pb-free marking indicates RoHS-compliant variant |
تكوين أطراف M30624FGPFP#U5C
| دبوس 1 | VREF — A/D converter reference voltage |
| دبوس 2 | AVSS — Analog ground |
| دبوس 3 | P9.7/AN7 — Port 9 / analog input |
| دبوس 4 | P9.6/AN6 — Port 9 / analog input |
| دبوس 5 | P9.5/AN5 — Port 9 / analog input |
| دبوس 6 | P9.4/AN4 — Port 9 / analog input |
| دبوس 7 | P9.3/AN3 — Port 9 / analog input |
| دبوس 8 | P9.2/AN2 — Port 9 / analog input |
| دبوس 9 | P9.1/AN1 — Port 9 / analog input |
| دبوس 10 | P9.0/AN0 — Port 9 / analog input |
| دبوس 11 | VCC — Digital supply |
| دبوس 12 | VSS — Digital ground |
| دبوس 13 | P8.7 — Port 8 / general-purpose I/O |
| دبوس 14 | P8.6 — Port 8 / general-purpose I/O |
| دبوس 15 | P8.5 — Port 8 / general-purpose I/O |
| دبوس 16 | P8.4 — Port 8 / general-purpose I/O |
| دبوس 17 | P8.3 — Port 8 / general-purpose I/O |
| دبوس 18 | P8.2 — Port 8 / general-purpose I/O |
| دبوس 19 | P8.1/AN15 — Port 8 / analog input |
| دبوس 20 | P8.0/AN14 — Port 8 / analog input |
| دبوس 21 | P7.7/INT7 — Port 7 / external interrupt |
| دبوس 22 | P7.6/INT6 — Port 7 / external interrupt |
| دبوس 23 | P7.5/INT5 — Port 7 / external interrupt |
| دبوس 24 | P7.4/INT4 — Port 7 / external interrupt |
| دبوس 25 | P7.3 — Port 7 / general-purpose I/O |
| دبوس 26 | P7.2 — Port 7 / general-purpose I/O |
| دبوس 27 | P7.1 — Port 7 / general-purpose I/O |
| دبوس 28 | P7.0 — Port 7 / general-purpose I/O |
| دبوس 29 | P6.7 — Port 6 / general-purpose I/O |
| دبوس 30 | P6.6 — Port 6 / general-purpose I/O |
| دبوس 31 | P6.5 — Port 6 / general-purpose I/O |
| دبوس 32 | P6.4 — Port 6 / general-purpose I/O |
| دبوس 33 | P6.3 — Port 6 / general-purpose I/O |
| دبوس 34 | P6.2 — Port 6 / general-purpose I/O |
| دبوس 35 | P6.1 — Port 6 / general-purpose I/O |
| دبوس 36 | P6.0 — Port 6 / general-purpose I/O |
| دبوس 37 | P5.7 — Port 5 / general-purpose I/O |
| دبوس 38 | P5.6 — Port 5 / general-purpose I/O |
| دبوس 39 | P5.5 — Port 5 / general-purpose I/O |
| دبوس 40 | P5.4 — Port 5 / general-purpose I/O |
| دبوس 41 | P5.3 — Port 5 / general-purpose I/O |
| دبوس 42 | P5.2 — Port 5 / general-purpose I/O |
| دبوس 43 | P5.1 — Port 5 / general-purpose I/O |
| دبوس 44 | P5.0 — Port 5 / general-purpose I/O |
| دبوس 45 | P4.7 — Port 4 / general-purpose I/O |
| دبوس 46 | P4.6 — Port 4 / general-purpose I/O |
| دبوس 47 | P4.5 — Port 4 / general-purpose I/O |
| دبوس 48 | P4.4 — Port 4 / general-purpose I/O |
| دبوس 49 | P4.3 — Port 4 / general-purpose I/O |
| دبوس 50 | P4.2 — Port 4 / general-purpose I/O |
| دبوس 51 | P4.1 — Port 4 / general-purpose I/O |
| دبوس 52 | P4.0 — Port 4 / general-purpose I/O |
| دبوس 53 | P3.7 — Port 3 / general-purpose I/O |
| دبوس 54 | P3.6 — Port 3 / general-purpose I/O |
| دبوس 55 | P3.5 — Port 3 / general-purpose I/O |
| دبوس 56 | P3.4 — Port 3 / general-purpose I/O |
| دبوس 57 | P3.3 — Port 3 / general-purpose I/O |
| دبوس 58 | P3.2 — Port 3 / general-purpose I/O |
| دبوس 59 | P3.1 — Port 3 / general-purpose I/O |
| دبوس 60 | P3.0 — Port 3 / general-purpose I/O |
| دبوس 61 | P2.7 — Port 2 / general-purpose I/O |
| دبوس 62 | P2.6 — Port 2 / general-purpose I/O |
| دبوس 63 | P2.5 — Port 2 / general-purpose I/O |
| دبوس 64 | P2.4 — Port 2 / general-purpose I/O |
| دبوس 65 | P2.3 — Port 2 / general-purpose I/O |
| دبوس 66 | P2.2 — Port 2 / general-purpose I/O |
| دبوس 67 | P2.1 — Port 2 / general-purpose I/O |
| دبوس 68 | P2.0 — Port 2 / general-purpose I/O |
| دبوس 69 | P1.7 — Port 1 / general-purpose I/O |
| دبوس 70 | P1.6 — Port 1 / general-purpose I/O |
| دبوس 71 | P1.5 — Port 1 / general-purpose I/O |
| دبوس 72 | P1.4 — Port 1 / general-purpose I/O |
| دبوس 73 | P1.3 — Port 1 / general-purpose I/O |
| دبوس 74 | P1.2 — Port 1 / general-purpose I/O |
| دبوس 75 | P1.1 — Port 1 / general-purpose I/O |
| دبوس 76 | P1.0 — Port 1 / general-purpose I/O |
| دبوس 77 | P0.7 — Port 0 / general-purpose I/O |
| دبوس 78 | P0.6 — Port 0 / general-purpose I/O |
| دبوس 79 | P0.5 — Port 0 / general-purpose I/O |
| دبوس 80 | P0.4 — Port 0 / general-purpose I/O |
| دبوس 81 | P0.3 — Port 0 / general-purpose I/O |
| دبوس 82 | P0.2 — Port 0 / general-purpose I/O |
| دبوس 83 | P0.1 — Port 0 / general-purpose I/O |
| دبوس 84 | P0.0 — Port 0 / general-purpose I/O |
| دبوس 85 | P10.7 — Port 10 / general-purpose I/O |
| دبوس 86 | P10.6 — Port 10 / general-purpose I/O |
| دبوس 87 | P10.5 — Port 10 / general-purpose I/O |
| دبوس 88 | P10.4 — Port 10 / general-purpose I/O |
| دبوس 89 | P10.3 — Port 10 / general-purpose I/O |
| دبوس 90 | P10.2 — Port 10 / general-purpose I/O |
| دبوس 91 | P10.1 — Port 10 / general-purpose I/O |
| دبوس 92 | P10.0 — Port 10 / general-purpose I/O |
| دبوس 93 | RESET — Reset input (active-low) |
| دبوس 94 | XOUT — Crystal oscillator output |
| دبوس 95 | XIN — Crystal oscillator input |
| دبوس 96 | VSS — Digital ground |
| دبوس 97 | VCC — Digital supply |
| دبوس 98 | CNVSS — Flash programming mode select |
| دبوس 99 | RXD/TXD — Serial debug / programming interface |
| دبوس 100 | P9.6 — Port 9 / general-purpose I/O |
التطبيقات النموذجية
M30624FGPFP#U5C مناسب لـ 6 التطبيقs: Industrial Motor Control, HVAC Control Board, Automotive Body ECU, Home Appliance Controllers, Smart Metering and Utility Monitoring, Industrial Sensor Hub / Data Logger.
Industrial Motor Control
The M30624FGPFP#U5C is well suited to industrial BLDC, stepper, and 3-phase AC induction motor control. Its three 16-bit timers with complementary PWM outputs drive 6-step or FOC commutation at 20 kHz with deterministic timing. The integrated 10-bit A/D converter with multiple input channels samples phase current, DC bus voltage, and back-EMF simultaneously within the PWM window. The 24 MHz M16C/60 CPU executes control loops with single-cycle efficiency, leaving headroom for the speed PI loop, fault handling, and serial comms to a host PLC. The 2.7V-5.5V supply lets the same board work from 24V industrial buses regulated to 5V or 3.3V rails.
موصى به
HVAC Control Board
The M30624FGPFP#U5C's wide 2.7-5.5V supply, 85 I/O pins, and 10-bit A/D converter are an excellent match for HVAC controller boards. Temperature sensors (NTC thermistors), pressure transducers, and humidity sensors all digitize directly into the A/D channels, while relays and triacs for compressor, fan, and valve control are driven by the parallel I/O ports. The 256 KB flash fits the full state machine for compressor sequencing, defrost cycles, and EEPROM-backed user settings. The M16C core's deterministic interrupt latency keeps the safety watchdog and over-temperature shutdown responsive even under heavy I/O load.
موصى به
Automotive Body ECU
Although not AEC-Q100 qualified, the M30624FGPFP#U5C has long been deployed in automotive body controllers for non-safety-critical functions like window lift, seat adjustment, mirror control, and lighting. The 100-QFP exposes enough I/O to drive multiple H-bridges and relay coils directly. The M16C/62P peripheral set includes CAN-ready timers and UART channels for LIN bus communication with other ECUs. The 256 KB flash stores the body-control state machine, while 4 KB RAM holds the CAN/LIN message buffers. Designers should note the -20C to +85C operating range suits cabin-mounted ECUs but not under-hood.
موصى به
Home Appliance Controllers
The M30624FGPFP#U5C powers washing machines, microwave ovens, dishwashers, induction cooktops, and rice cookers. Its 24 MHz CPU runs the user-interface state machine (buttons, LCD/LED display, buzzer), the motor/relay control loop, and the safety supervisory loop concurrently. The flash-based architecture supports firmware updates via UART boot mode for after-sale service. The wide 2.7-5.5V supply lets the MCU run directly from rectified 5V or 3.3V rails. The 4 KB RAM comfortably holds the user interface buffers and sensor-history arrays, and the integrated 10-bit A/D reads NTC temperature probes and water-level sensors.
موصى به
Smart Metering and Utility Monitoring
The M30624FGPFP#U5C is a strong fit for electricity, water, and gas metering front-ends. Its 10-bit A/D converter reads voltage and current sense channels for basic power calculation, and the UART/SPI peripherals interface with metering ICs and RF modules for wireless M-Bus or LoRaWAN communication. The 256 KB flash is sufficient for TOU (time-of-use) tariff tables, rolling consumption logs, and LCD segment drivers. Low-power modes supported by the M16C/60 core extend battery life in gas and water meters. The wide operating voltage tolerates long battery discharge curves down to 2.7V.
موصى به
Industrial Sensor Hub / Data Logger
The M30624FGPFP#U5C can serve as a multi-channel sensor hub for industrial data acquisition, aggregating analog inputs from 4-20 mA loop-powered sensors and serial data from UART/SPI/I2C peripherals. Its 85 I/O pins interface directly with parallel LCD modules, keypad matrices, and discrete indicator LEDs, eliminating external I/O expanders. The M16C/62P timer block provides accurate timestamping for logged events, while the flash holds historical data buffers with wear-leveling. The wide 2.7-5.5V supply allows the same board to operate in factory 24V systems and 3.3V battery-powered remote sites.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ M30624FGPFP#U5C — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | M3062LFGPFP | M3062LFGPFP#U5C | M30624FGPGP | M30624FGPGP#U5C | M30626FJPFP#U5C |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 100-QFP (14x20 mm) | 100-QFP (14x20 mm) - same | 100-QFP (14x20 mm) - same | 100-QFP (14x20 mm) - same | 100-QFP (14x20 mm) - same | 100-QFP (14x20 mm) - same |
| Maximum CPU Clock | 24 MHz | 24 MHz | 24 MHz | 24 MHz | 24 MHz | 24 MHz |
| Operating Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Core | M16C/60 16-bit | M16C/60 16-bit | M16C/60 16-bit | M16C/60 16-bit | M16C/60 16-bit | M16C/60 16-bit |
| Pb-free / RoHS | Yes (#U5C) | No (standard) | Yes | No (standard) | Yes | Yes |
| Recommended for New Designs | No (NRND) | Yes (Renesas recommended) | Yes (Renesas recommended) | No | No | No |
أبرز الفروقات
- Recommended successor from the same silicon family (مقابلM3062LFGPFP)
- Same silicon as M30624FGPFP, Pb-free RoHS suffix only (مقابلM30624FGPFP (non-#U5C))
- Higher integration than smaller M16C siblings (مقابلM30624FGPGP)
ملاحظات التصميم
Place a 100 nF ceramic decoupling capacitor as close as possible to each VCC/VSS pair (pins 11/12, 96/97, plus any AVCC/AVSS) and a single 10 uF bulk capacitor near the package. The M16C/62P has multiple VCC pins that must all be connected for proper operation. The wide 2.7V-5.5V supply range lets you derive power from either a 3.3V LDO (e.g., LT8606) or a 5V linear regulator (e.g., LM7805). Add a power-on reset circuit if your system does not have a clean 3V/5V ramp.
The 100-QFP (14x20 mm) has a 0.65 mm pitch. Per IPC-2221, allocate at least 0.4 mm trace clearance and use 4-layer PCB stack-up with continuous ground plane beneath the IC to reduce EMI. Use wide power traces (>=0.5 mm) for VCC/VSS pins. Place the crystal (typically 8 MHz fundamental) within 5 mm of XIN/XOUT (pins 94/95) and guard the traces with a ground ring. Connect the MCU thermal pad to a 10x10 mm copper pour on top and bottom layers stitched with thermal vias.
Do not leave any VCC pin floating - the M30624FGPFP#U5C has multiple supply pins that must all be tied to the same rail, or the device may latch up or behave unpredictably. The CNVSS pin (pin 98) selects between standard and flash programming modes and must be tied to VCC for normal operation, or to a programming connector for flash update. The RESET pin (pin 93) is active-low and requires a pull-up plus a 1 nF capacitor for proper debounce. Do not exceed 5.5V on any pin - the absolute maximum VCC is 6V.
Keep analog inputs (AN0-AN15 on ports P8/P9) physically separated from switching signals like PWM outputs and the crystal traces. Use a separate analog ground (AVSS) island connected to digital ground (VSS) at a single point near the MCU. The VREF pin (pin 1) drives the A/D reference and should be decoupled with a 1 uF ceramic + 100 nF combination. Keep high-current traces (motor drivers, relays) routed away from the analog input pins to minimize coupled noise into A/D readings.
معلومات الامتثال
Pb-free / RoHS-compliant per the #U5C suffix and JLCPCB ROHS attribute. Not AEC-Q100 qualified. REACH, halogen-free, and conflict-mineral declarations should be requested from Renesas directly.
