MAX232CEAWE+ - +5V RS-232 Transceiver | Analog Devices
MPN: MAX232CEAWE+ ✓ نشطMAX232CEAWE+ نظرة عامة
An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and RS-232 line drivers and receivers. The MAX232 family belongs to the interface IC hierarchy, where transceiver ICs bridge digital logic systems with the voltage levels, slew rates, and noise-immunity requirements of balanced or unbalanced serial communications. It is particularly useful where the equipment does not provide the traditional positive and negative RS-232 supply rails.
The MAX232CEAWE+ uses a single +5V supply, combining two transmit channels and two receive channels in one package. This integration reduces the number of components required for a bidirectional RS-232 port. Its stated interface compatibility includes EIA/TIA-232E, V.28, and V.24 systems, while its 16-SOIC format supports conventional surface-mount PCB assembly. The E designation identifies an industrial-temperature device within the MAX232 family.
Operationally, the transmitter portion converts TTL or CMOS logic levels into RS-232-compatible signal levels, while the receiver portion converts incoming RS-232 signals into logic-compatible outputs. The MAX232 family is intended specifically for communications interfaces where positive and negative supply voltages are unavailable. Its internal charge-pump approach allows +5V-powered equipment to implement RS-232 links without external negative-rail generation circuitry.
Typical applications include industrial serial adapters, data-acquisition equipment, instrumentation, embedded controller interfaces, point-of-sale systems, and legacy peripheral connections. A two-driver, two-receiver arrangement is useful for consoles, debug ports, programmable instruments, and control systems that exchange data in both directions over separate RS-232 channels.
PCB design should prioritize short return paths and controlled return current around the interface. Place the device close to the connector and keep unprotected RS-232 traces away from sensitive analog or high-speed digital nets. The manufacturer's pin-description table should be used when assigning connector-side and logic-side signals, and external protection should be selected for the cable length and installation environment.
This product page combines the manufacturer interface description with package, application, and drop-in selection guidance. It also highlights where temperature-grade, ESD-protection, and footprint differences matter when comparing MAX232-family devices for an existing 16-SOIC PCB design.
بدائل مباشرة لـ MAX232CEAWE+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MAX232CEAWE+ (نفس عامل الشكل والبصمة) — يختلف في Interface Standard, Product Type, Package, Maximum Data Rate, Driver and Receiver Count.
MAX232CWE+
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX232EWE+T
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX232EESE+
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX232AEWE+
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX232ACWE+
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX232CEAWE+ المواصفات
| Product Type | 2/2 RS-232 transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| جهد التغذية | +5 V |
| Interface Standard | EIA/TIA-232E |
| Protocol Support | V.28 and V.24 |
| العلبة | 16-SOIC |
| نوع التركيب | Surface mount |
| تكوين الخرج | Full RS-232 |
| Driver and Receiver Count | 2 transmitters and 2 receivers |
| Supply Configuration | Single +5 V supply |
دليل تكوين أطراف MAX232CEAWE+ 16-soic
تكوين الأطراف لـ MAX232CEAWE+ (حزمة 16-soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX232CEAWE+.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX232CEAWE+ مناسب لـ 6 التطبيقs: Industrial Serial Controllers, Data-Acquisition Instruments, Embedded Controller Service Ports, Point-of-Sale Terminals, Programmable Test Equipment, Legacy Peripheral Connectivity.
Industrial Serial Controllers
The MAX232CEAWE+ fits industrial controllers that expose an RS-232 service or configuration port while operating from a +5 V logic rail. Its 2/2 configuration provides two driver channels and two receiver channels in one 16-SOIC package, reducing the component count compared with separate single-channel interface devices. The MAX232 family targets EIA/TIA-232E, V.28, and V.24 communication requirements where positive and negative supply rails are unavailable. For industrial deployment, place the IC close to the connector, route return currents carefully, and select external surge protection according to the cable length and installation environment.
موصى به
Data-Acquisition Instruments
The MAX232CEAWE+ is suitable for data-acquisition instruments that need a legacy serial console alongside a data channel. Two transmitters and two receivers in a 16-SOIC package allow bidirectional communication without adding separate RS-232 interface packages. Operating from +5 V is especially useful when the instrument already has a +5 V logic rail but cannot readily provide the traditional positive and negative RS-232 supply levels. Because the MAX232 family supports EIA/TIA-232E, V.28, and V.24, it fits many legacy test and measurement interfaces. Confirm data rate, receiver threshold, and connector-side protection against the final instrument specification.
موصى به
Embedded Controller Service Ports
The MAX232CEAWE+ can implement a service or debug port on an embedded controller board powered from +5 V. Its two-driver, two-receiver arrangement supports separate command and response paths, while the 16-SOIC package keeps the footprint compact for surface-mount assembly. The device's +5 V operating requirement avoids external negative-rail generation, and its EIA/TIA-232E, V.28, and V.24 support makes it appropriate for conventional controller peripherals. Place the transceiver near the serial connector, keep ground and signal returns together, and use the manufacturer pin table to assign logic-side and connector-side signals correctly.
موصى به
Point-of-Sale Terminals
The MAX232CEAWE+ is appropriate for point-of-sale and peripheral equipment that communicates with older RS-232 devices. Two transmit channels and two receive channels provide enough connectivity for a bidirectional peripheral link or paired control channels in a 16-SOIC package. Since the device runs from a single +5 V supply, it can simplify power planning in terminals built around +5 V logic. The MAX232 family's EIA/TIA-232E, V.28, and V.24 compatibility supports established serial-control applications. External protection remains important when the equipment uses long cables or exposed connectors, and firmware should configure the host UART to the selected channel's supported rate.
موصى به
Programmable Test Equipment
The MAX232CEAWE+ is useful in programmable instruments that need a standardized serial control interface for calibration, logging, or remote commands. The integrated 2/2 transceiver architecture permits two driver and two receiver paths while retaining a conventional 16-SOIC surface-mount package. A single +5 V supply is compatible with many instrument logic rails and eliminates the need for a separate negative supply stage in the RS-232 interface. The MAX232 family's support for EIA/TIA-232E, V.28, and V.24 enables communication with legacy controllers and test fixtures. Verify the maximum supported data rate and timing margin for the chosen instrument processor before production.
موصى به
Legacy Peripheral Connectivity
The MAX232CEAWE+ provides a practical bridge between modern +5 V control logic and legacy RS-232 peripherals. Its two transmitters and two receivers support separate communication paths in one 16-SOIC device, and its support for EIA/TIA-232E, V.28, and V.24 broadens compatibility with established serial equipment. The integrated interface is preferable to discrete driver and receiver networks when board space is constrained. Route the connector-side traces as a compact differential-free pair, maintain a continuous ground reference, and install suitable transient protection if the peripheral cable leaves the enclosure. Check receiver logic thresholds against the peripheral's output voltage.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX232CEAWE+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX232CWE+ | MAX232EWE+T | MAX232EESE+ | MAX232AEWE+ | MAX232ACWE+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Product Type | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver |
| Driver and Receiver Count | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| Temperature Grade | E-grade industrial-temperature option | Commercial-temperature option | E-series option | E-series option | A-series option | A-series option |
| Surface-Mount Form | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
أبرز الفروقات
- E-grade temperature positioning (مقابلMAX232CWE+)
- Full-duplex channel integration (مقابلMAX232AEWE+)
- Single +5 V interface implementation (مقابلMAX232ACWE+)
ملاحظات التصميم
Place the MAX232CEAWE+ close to the RS-232 connector and place the connector-side protection components directly beside the connector. Keep logic-side traces away from unprotected RS-232 nets, and route the ground return continuously beneath or adjacent to the signal path. This arrangement reduces radiated coupling and helps the receiver maintain reliable behavior in industrial environments where external cables can pick up transient noise.
Do not treat every MAX232 suffix as electrically identical. The MAX232CEAWE+ is the E-grade 16-SOIC device, while MAX232CWE+, MAX232AEWE+, and MAX232ACWE+ represent different ordering classes. Before substituting a device, compare temperature limits, ESD withstand ratings, driver and receiver timing, supply current, and the exact pin-description table. A shared 16-SOIC footprint alone does not establish that a part is qualified for every operating environment.
Keep the RS-232 connector, driver outputs, and receiver inputs away from clocks, switching regulators, and high-current return paths. Use a compact ground reference for the interface and avoid routing the cable-side nets beneath unrelated digital activity. If the product includes surge or ESD protection, select its capacitance and clamp behavior carefully so it does not degrade receiver thresholds or the intended communication rate.
معلومات الامتثال
The MAX232 is an industrial interface IC rather than an automotive-qualified device, so AEC-Q100 is not applicable. RoHS, REACH, lead-free, and halogen-free status require confirmation from the relevant manufacturer product documentation for the exact ordering code.