Texas Instruments

MAX232EIDW - 250kbps RS-232 Transceiver | Texas Instruments

MPN: MAX232EIDW ✓ نشط
5 V Vdss 16-pin SOIC (DW) Package
الحد الأدنى للطلب: 1 |

MAX232EIDW نظرة عامة

Texas Instruments MAX232EIDW is a dual-channel RS-232 line driver/receiver with a 250 kbps data rate, 5 V supply, and ±9 V driver output levels in a 16-pin SOIC (DW) package. It adds ±15 kV IEC 61000-4-2 ESD protection to the established MAX232 dual-driver, dual-receiver architecture.

A RS-232 transceiver is an interface IC that converts logic-level signals between TTL/CMOS equipment and balanced, bipolar RS-232 lines. Within the interface hierarchy, the MAX232E belongs to the line-driver/receiver family, implements the RS-232 physical-layer interface, and supports communication between equipment that uses different voltage domains. Its integrated charge-pump circuitry generates the required positive and negative voltage from one 5 V supply.

The device provides two transmit channels and two receive channels for full-duplex serial links. According to the Texas Instruments MAX232 datasheet, each receiver accepts inputs up to ±30 V, uses a typical threshold of 1.3 V, and has typical hysteresis of 0.5 V. The enhanced MAX232E variant supports 250 kbps operation and ±15 kV IEC-ESD protection, making it suitable for industrial control, instrumentation, and equipment interfaces exposed to electrostatic discharge.

Internally, the charge-pump voltage generator produces the bipolar voltages required by RS-232 drivers while onboard capacitors provide the required charge-pump operation. The MAX232EIDW is specified for operation from −40 °C to +85 °C and uses the DW 16-pin SOIC package. Receiver inputs can withstand bipolar voltages up to ±30 V, while the drivers supply approximately ±9 V output levels for compliant RS-232 signaling.

Typical uses include industrial serial consoles, programmable test equipment, data-acquisition systems, point-of-sale terminals, and embedded controllers communicating with legacy RS-232 peripherals. The ±15 kV ESD rating is especially useful where a connector cable can expose the interface to electrostatic discharge, although system-level protection and grounding remain necessary for long or outdoor cables.

When laying out the circuit, place the charge-pump capacitors close to their associated pins and keep the RS-232 traces away from sensitive analog and high-speed digital paths. Provide a solid ground-plane connection and use appropriate cable transient protection when the interface leaves an enclosure. This page combines manufacturer specifications, replacement guidance, application engineering notes, and same-package comparisons for faster component selection and PCB planning.

بدائل مباشرة لـ MAX232EIDW — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع MAX232EIDW (نفس عامل الشكل والبصمة) — يختلف في ESD Protection, Package, Product Type, Supply Voltage, Interface Standard.

Texas Instruments
ESD Protection: ±2 kV
Package: 16-pin SOIC
Product Type: Dual RS-232 driver/receiver transceiver
قارن مع MAX232EIDW →
Analog Devices
ESD Protection: ±15 kV human body model
Package: 16-pin SOIC, 3.90 mm width
Product Type: RS-232 transceiver
قارن مع MAX232EIDW →

MAX232EESE+T

✅ بديل مباشر
Analog Devices
📦 SOIC-16 (DW)
RS-232 transceiver · 2 · 2 · Full duplex · Up to 120 kbps · +5 V · ±15 kV human body model · EIA/TIA-232E and CCITT V.28

تواصل لمعرفة السعر

عرض ورقة البيانات ←

MAX232ECWE-T

✅ بديل مباشر
📦 SOIC-16 (DW)
Same dual RS-232 driver/receiver and 16-pin SOIC interface, while the EC ordering suffix changes temperature-grade and package-width options; verify the DW footprint before substitution.

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX232IDW

✅ بديل مباشر
Texas Instruments
📦 SOIC-16 (DW)
2/2 dual driver and receiver · 2 · 2 · 120 kbps · 5 V · 4.5 V to 5.5 V · ±9 V · ±30 V

تواصل لمعرفة السعر

عرض ورقة البيانات ←

MAX232DWR

✅ بديل مباشر
Texas Instruments
📦 SOIC-16 (DW)
Dual RS-232 driver/receiver transceiver · 2 · 2 · 5 V · 120 kbit/s · ±9 V · ±30 V · ±2 kV

تواصل لمعرفة السعر

عرض ورقة البيانات ←

MAX232EIDW المواصفات

Product Type Dual RS-232 driver/receiver
Number of Transmit Channels 2 channels
Number of Receive Channels 2 channels
Maximum Data Rate 250 kbps
جهد التغذية 5 V
Driver Output Level ±9 V
Receiver Maximum Input Voltage ±30 V
Receiver Typical Threshold 1.3 V
Receiver Typical Hysteresis 0.5 V
ESD Protection ±15 kV IEC 61000-4-2
نطاق درجة حرارة التشغيل −40 °C to +85 °C
العلبة 16-pin SOIC (DW)
عدد الأطراف 16 pins
نوع التركيب Surface mount
Logic Levels 5 V TTL/CMOS
Interface Standard RS-232
Charge-Pump Voltage Generation Integrated, single 5 V supply

دليل تكوين أطراف MAX232EIDW 16-pin soic (dw)

تكوين الأطراف لـ MAX232EIDW (حزمة 16-pin soic (dw)). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 16-pin soic (dw) لـ MAX232EIDW

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX232EIDW.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

MAX232EIDW مناسب لـ 6 التطبيقs: Industrial Serial Console Interface, Data Acquisition and Test Equipment, Programmable Controller Communication, Point-of-Sale Terminal Interface, Legacy Peripheral Connectivity, Instrumentation and Measurement Networks.

🏭

Industrial Serial Console Interface

The MAX232EIDW fits industrial serial-console designs that require a 5 V logic-side interface and RS-232 levels on the cable side. Its dual transmitters and dual receivers support one full-duplex link, while the 250 kbps maximum rate provides more than enough bandwidth for terminal traffic. The −40 °C to +85 °C operating range supports equipment deployed in temperature-controlled industrial spaces. Its ±15 kV IEC 61000-4-2 protection rating improves interface survivability when the connector is accessible to personnel or maintenance equipment. The transmitter produces approximately ±9 V levels from the internal charge pump, so the system needs only one 5 V supply.

🔧

Data Acquisition and Test Equipment

MAX232EIDW is appropriate for data-acquisition instruments that exchange commands and measurement results with a host over RS-232. The 250 kbps maximum signaling rate supports moderate-rate telemetry while preserving compatibility with legacy equipment. Two receivers and two drivers allow one full-duplex port, and the 5 V operating supply simplifies integration with digital control circuitry. For bench instruments with exposed serial connectors, ±15 kV IEC 61000-4-2 protection adds useful electrostatic-discharge margin. Designers should still keep the interface ground connected to the chassis and evaluate additional surge protection for cables longer than a short bench lead.

⚡

Programmable Controller Communication

The MAX232EIDW can connect a 5 V embedded controller to an RS-232 host, service console, or configuration utility. The dual-driver, dual-receiver arrangement supports bidirectional command and data traffic without external level-shifting transistors. Its 250 kbps capability allows firmware to use a practical serial rate below the device maximum, while the integrated voltage generator avoids separate RS-232 power rails. For production equipment, the −40 °C to +85 °C rating provides useful environmental range. Because the MAX232EIDW has no automatic direction control, the controller must manage transmitter enable state unless the selected connector wiring guarantees that only one transmitter is active.

🖥️

Point-of-Sale Terminal Interface

MAX232EIDW is suitable for point-of-sale equipment that communicates with scanners, receipt printers, or service equipment over legacy RS-232. Its 5 V supply is convenient for systems already powered by a regulated 5 V rail, and the integrated charge pump provides approximately ±9 V driver outputs without a separate negative supply. The 250 kbps limit is substantially above the throughput of many point-of-sale peripherals. If the port is accessible through a service connector, the ±15 kV IEC 61000-4-2 rating improves robustness against electrostatic discharge. The final design should include a defined signal ground, short connector lead, and firmware that avoids enabling multiple transmitters simultaneously.

🔌

Legacy Peripheral Connectivity

MAX232EIDW provides a practical interface between modern 5 V digital electronics and legacy RS-232 peripherals such as older test equipment, industrial controllers, and service interfaces. The receiver translates bipolar line signals into 5 V TTL/CMOS levels, and the transmitter converts logic inputs into approximately ±9 V RS-232 outputs. Its receiver can accept bipolar inputs up to ±30 V, providing tolerance for off-state noise and standard RS-232 swings. The 250 kbps rate allows operation above the throughput of many legacy devices. Firmware should use framed packets and controlled transmitter states, while the PCB must provide the charge-pump capacitors and stable 5 V decoupling specified by the manufacturer.

📟

Instrumentation and Measurement Networks

MAX232EIDW can bridge a 5 V measurement instrument to an RS-232 network of analyzers, source meters, or laboratory controllers. The 250 kbps maximum rate supports compact command-and-response protocols, while two receivers and two drivers provide flexible full-duplex channel use. The device operates across −40 °C to +85 °C, making it suitable for instrumentation intended for industrial environments as well as laboratories. Its ±15 kV IEC 61000-4-2 protection is useful when users repeatedly connect external cables, but it is not a substitute for correctly implemented cable grounding. Keep the interface ground and signal return together and isolate long external cable runs from sensitive measurement circuitry.

What is the MAX232EIDW?
The MAX232EIDW is a Texas Instruments dual-channel RS-232 transceiver that provides two drivers and two receivers for full-duplex serial communication. According to the Texas Instruments MAX232 datasheet, it operates from a single 5 V supply, supports data rates up to 250 kbps, and generates approximately ±9 V driver outputs through an integrated charge-pump circuit. The device is packaged in a 16-pin SOIC designated DW.
Where can I download the MAX232EIDW datasheet PDF?
The official MAX232EIDW datasheet PDF is available from the Texas Instruments product link at https://www.ti.com/lit/ds/symlink/max232.pdf. The manufacturer product-detail page for MAX232EIDW also provides ordering, lifecycle, and package information. Use the Texas Instruments PDF for the authoritative pin description, electrical characteristics, charge-pump capacitor requirements, and application guidance.
What is the operating voltage of MAX232EIDW?
The MAX232EIDW operates from a single 5 V supply. Its integrated charge-pump circuitry generates the positive and negative voltages needed by the RS-232 drivers, so the circuit does not require separate positive and negative supply rails. The Texas Instruments MAX232 datasheet identifies this as a 5 V dual driver/receiver, with approximately ±9 V outputs on the driver side.
What is the maximum data rate of MAX232EIDW?
The MAX232EIDW supports a maximum signaling rate of 250 kbps. According to the Texas Instruments MAX232E product information, it is a dual-channel RS-232 line driver/receiver with ±9 V output and ±15 kV IEC-ESD protection. This rate is suitable for instrumentation, industrial control links, and legacy serial devices operating well below the device's specified maximum.
What ESD protection does MAX232EIDW provide?
The MAX232EIDW provides ±15 kV IEC 61000-4-2 ESD protection on its RS-232 interface. According to the Texas Instruments MAX232E product-detail information, this enhanced protection is intended to improve survivability against electrostatic discharge at externally accessible connectors. It does not eliminate the need for good enclosure grounding, short cables, and appropriate system-level transient protection.
What package and pin count does MAX232EIDW use?
The MAX232EIDW uses a 16-pin SOIC package with the manufacturer package code DW. The Texas Instruments MAX232E product page lists 16 pins and an operating range of −40 °C to +85 °C. Because the DW outline is a 16-pin SOIC, a board footprint must provide all 16 electrical positions and follow the manufacturer's land-pattern guidance.
Where can I find the MAX232EIDW pinout and package drawing?
The MAX232EIDW pin descriptions and DW package drawing are in the official Texas Instruments MAX232 datasheet and the MAX232E product-detail page. The manufacturer lists the device as a 16-pin SOIC. Use the pin-description table when assigning PCB nets, and use the DW mechanical drawing rather than assuming that a generic 16-pin footprint will satisfy thermal, lead-width, or land-pattern requirements.
Is MAX232EIDW suitable for industrial equipment?
The MAX232EIDW is well suited to industrial RS-232 interfaces because it operates from −40 °C to +85 °C and includes ±15 kV IEC 61000-4-2 ESD protection. Its 5 V supply, 250 kbps maximum data rate, and dual-driver, dual-receiver arrangement support legacy industrial terminals, controllers, and test equipment. Long cable installations still require chassis grounding and appropriate transient suppression.
What can replace MAX232EIDW?
The closest same-footprint choices include MAX232IDW, MAX232ECWE-T, MAX232EESE+T, and MAX232DWR. Replacement should be based on the exact data rate, temperature grade, package width, and ESD requirement rather than the RS-232 label alone. The Texas Instruments MAX232 family shares the core driver/receiver function, but ordering suffixes can alter speed, temperature range, package width, or qualification.
Is MAX232IDW the same as MAX232EIDW?
MAX232IDW is not an exact functional match for every MAX232EIDW specification. The Texas Instruments MAX232 product information describes MAX232 as a 120 kbps interface, while MAX232E supports 250 kbps and ±15 kV IEC-ESD protection. Both use a 16-pin DW-class package, so MAX232IDW may be pin-compatible, but it should be selected only when its lower data rate and protection specification meet the design requirements.
When should I choose MAX232EIDW over MAX232IDW?
Choose MAX232EIDW when the interface requires operation above 120 kbps or needs the enhanced ±15 kV IEC 61000-4-2 protection rating. According to the Texas Instruments product information, MAX232IDW supports 120 kbps, whereas the MAX232E variant supports 250 kbps. MAX232IDW may still be adequate for slow legacy links, but the enhanced part provides additional margin for higher-throughput and electrically exposed interfaces.
What is the best MAX232EIDW replacement for a new design?
The best replacement is the same-family ordering option that preserves the 16-pin DW footprint, 250 kbps data rate, −40 °C to +85 °C range, and required ESD protection. MAX232EESE+T and MAX232ECWE-T appear in comparisons with MAX232EIDW, but package width and temperature-grade suffixes must be checked. For new designs, Texas Instruments recommends reviewing current MAX232E ordering options and the product lifecycle status before releasing the PCB.
MAX232EIDW vs MAX232EESE+T - which is better?
MAX232EIDW is the better choice when the full 16-pin DW outline, −40 °C to +85 °C range, and direct MAX232E ordering configuration are required. MAX232EESE+T may differ in package width and ordering suffix, so its mechanical drawing must match the existing PCB footprint. Both belong to the enhanced MAX232E RS-232 family, but suffix differences can affect fit, temperature grade, and procurement configuration.
What is the best Analog Devices equivalent for MAX232EIDW?
The Analog Devices MAX232 family provides the same general category of 5 V RS-232 driver/receiver functionality, but an exact drop-in decision requires an exact ordering suffix with a verified 16-pin DW footprint. The Analog Devices product page identifies MAX232 as a production 5 V multichannel RS-232 driver/receiver. Compare speed, temperature range, ESD rating, package dimensions, and pin names against the Texas Instruments datasheet before substituting it.
How do I request a quote, current availability, and lead time for MAX232EIDW?
Use the Request a Quote form on this page to request current availability, lead time, and commercial terms for MAX232EIDW. The manufacturer lists the device as on order and identifies the MAX232E family as active, but quotation-based sourcing is appropriate because inventory and lead time can change. Include your required quantity, DW package handling, and target delivery date in the request.

بيانات مرجعية هندسية لـ MAX232EIDW — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose MAX232EIDW when the design needs a 5 V, dual-channel RS-232 interface operating up to 250 kbps with ±15 kV IEC 61000-4-2 protection and a −40 °C to +85 °C temperature range. It is the appropriate choice for industrial controllers, instrumentation, and exposed service ports where the base MAX232 family's 120 kbps rating or lower documented ESD capability is insufficient. MAX232EESE+T and MAX232ECWE-T can be considered for redesigned boards after checking package width, temperature suffix, and ordering configuration. MAX232IDW or MAX232DWR may fit legacy links limited to 120 kbps, but they should not replace MAX232EIDW without confirming speed, protection, and environmental requirements. For new designs, evaluate the current Texas Instruments MAX232 family comparison to determine whether an updated RS-232 device provides a better long-term fit.

المقارنة مع البدائل

المعامل هذا المنتج MAX232EESE+T MAX232ECWE-T MAX232IDW MAX232DWR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SOIC-16 (DW) SOIC-16 (DW) SOIC-16 (DW) SOIC-16 (DW) SOIC-16 (DW)
Maximum Data Rate 250 kbps 250 kbps 250 kbps 120 kbps 120 kbps
Supply Voltage 5 V 5 V 5 V 5 V 5 V
Driver Output Level ±9 V ±9 V ±9 V ±9 V ±9 V
Transmit Channels 2 channels 2 channels 2 channels 2 channels 2 channels
Receive Channels 2 channels 2 channels 2 channels 2 channels 2 channels
Integrated Charge Pump Yes Yes Yes Yes Yes

أبرز الفروقات

  • Higher maximum signaling rate than the base MAX232 options (مقابلMAX232IDW)
  • Enhanced ESD protection for accessible RS-232 connectors (مقابلMAX232DWR)
  • Industrial temperature capability in the same 16-pin DW package (مقابلMAX232IDW)
  • Higher data rate with the same approximately ±9 V driver output (مقابلMAX232ECWE-T)

ملاحظات التصميم

Follow the Texas Instruments MAX232 datasheet layout guidance for the charge-pump capacitors and place them close to the designated IC pins. Keep these high-current switching paths compact and connect the chip ground directly to the ground plane. Avoid routing the charge-pump node beneath sensitive analog or high-speed digital traces because the switched node can couple noise into adjacent circuits.

Do not assume that every MAX232 ordering suffix is an electrical and mechanical substitute. MAX232IDW is listed at 120 kbps, while MAX232EIDW supports 250 kbps and ±15 kV IEC-ESD protection. Confirm the data rate, temperature grade, package width, exposed-pin arrangement, and pin functions before replacing a component on an existing PCB.

RS-232 can carry large transients when a cable is connected or disconnected. Connect the interface ground to the equipment chassis or ground structure at the connector entry, keep the cable return adjacent to the signal conductors, and avoid long unprotected stubs. The MAX232EIDW's ±15 kV IEC 61000-4-2 rating should be treated as component-level protection rather than a complete cable-surge solution.

Decouple the 5 V supply locally and follow the manufacturer capacitor recommendations. The MAX232EIDW includes a charge-pump generator, but its switched-capacitor operation draws periodic current from the supply. Use short, low-impedance power and ground paths, and verify that the source rail has adequate transient response for the installed board and cable interface.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The manufacturer identifies ±15 kV IEC 61000-4-2 ESD protection for the MAX232E family. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current regional compliance documentation.

عمليات بحث ذات صلة

MAX232EIDW datasheet MAX232EIDW pinout MAX232EIDW datasheet pdf MAX232EIDW equivalent MAX232EIDW replacement MAX232EIDW cross reference MAX232EIDW vs MAX232IDW MAX232EIDW footprint MAX232EIDW application circuit Texas Instruments MAX232EIDW MAX232EIDW 250kbps RS-232 MAX232EIDW 16-SOIC MAX232EIDW price MAX232EIDW stock

المكونات والمصطلحات ذات الصلة

Texas Instruments MAX232EIDW MAX232E MAX232EESE+T MAX232ECWE-T MAX232IDW MAX232DWR MAX3232E Analog Devices RS-232 RS-232 transceiver line driver line receiver interface IC semiconductor 5 V TTL/CMOS 250 kbps 120 kbps ±9 V ±30 V IEC 61000-4-2 ±15 kV ESD protection charge-pump voltage generator SOIC-16 DW package
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر