Analog Devices

MAX309EPE+ - Dual 4:1 CMOS Multiplexer | Analog Devices

MPN: MAX309EPE+ ✓ نشط
±5 V to ±30 V and ±20 V Vdss 750 pA Id Less than 100 ohm Rds(on) 16-pin PDIP Package
الحد الأدنى للطلب: 1 |

MAX309EPE+ نظرة عامة

The Analog Devices MAX309EPE+ is a dual 4:1 CMOS analog multiplexer with 2 circuits, less than 100 ohm on resistance, 150 ns switching performance, and a 16-pin PDIP package. Its multiplexers support ±5 V to ±30 V and ±20 V signal ranges, depending on the selected supply arrangement.

A CMOS analog multiplexer is an interface IC that routes one of several input signals to a shared output under digital control. The MAX309 belongs to the analog switch and multiplexer hierarchy, where it combines bidirectional signal routing, low on resistance, and precise channel matching. Each internal 4:1 circuit uses address logic to select one of four analog inputs for connection to its common output.

Key characteristics include on resistance below 100 ohm, channel-to-channel matching within 5 ohm, and on-resistance variation of no more than 7 ohm across the specified analog signal range. The device also provides break-before-make operation and approximately 750 pA of leakage-related current in the cited technical listing. These characteristics support accurate routing of moderate-voltage analog signals without introducing substantial insertion resistance.

The MAX309EPE+ is implemented as a precision monolithic CMOS device, with two independently addressed 4:1 sections. Its 150 ns switching figure supports applications requiring fast selection among sensors, measurement channels, or control signals. Matching between channels and flat on resistance across the analog range help preserve signal amplitude and balance when different sources are selected.

Typical uses include instrumentation signal selection, data-acquisition systems, industrial control interfaces, test and measurement equipment, and analog signal routing where several sources share a common processing chain. The dual-circuit organization can route two independent signal groups or provide two complementary multiplexed paths on the same board.

PCB design should preserve the 16-pin PDIP footprint and route each analog input directly to its intended pin. Keep sensitive analog traces away from digital address and control lines, provide clean supply decoupling, and use short connections to minimize parasitic capacitance. Verify the selected supply and input ranges against the MAX309 datasheet before connecting external signals.

This page combines manufacturer product information, distributor listings, same-family drop-in candidates, application guidance, and practical design notes to support component selection and PCB implementation.

بدائل مباشرة لـ MAX309EPE+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

MAX309CPE+

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 16-PDIP
Commercial-temperature ordering grade versus the industrial-grade MAX309EPE+; the numeric commercial temperature range is .

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX309EPE

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 16-PDIP
Earlier ordering designation without the plus suffix; core dual 4:1 electrical architecture is unchanged, while the maximum junction-temperature rating differs by 15°C.

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX309EPE+ المواصفات

Multiplexer Configuration Dual 4:1
Number of Circuits 2 circuits
On Resistance Less than 100 ohm
On-Resistance Matching Between Channels Within 5 ohm
On-Resistance Variation Across Signal Range 7 ohm maximum
Switching Time 150 ns
Leakage Current 750 pA
Signal Voltage Range ±5 V to ±30 V and ±20 V
جهد التغذية 5 V
Switching Behavior Break-before-make
Technology Precision monolithic CMOS
Temperature Grade Industrial
العلبة 16-pin PDIP
Package Pitch 7.62 mm
نوع التركيب Through-hole
Shipping Format Tube

دليل تكوين أطراف MAX309EPE+ 7.62 mm

تكوين الأطراف لـ MAX309EPE+ (حزمة 7.62 mm). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 7.62 mm لـ MAX309EPE+

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX309EPE+.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

MAX309EPE+ مناسب لـ 6 التطبيقs: Data-Acquisition Signal Selection, Industrial Sensor Interface, Precision Test and Measurement, Control Signal Routing, Analog Signal Fan-Out, Audio and Communication Routing.

📊

Data-Acquisition Signal Selection

The MAX309EPE+ fits data-acquisition boards that must select among several analog inputs while preserving signal amplitude and balance. Its two independent 4:1 sections can route two groups of four sources, reducing the number of separate multiplexers needed on the board. Less than 100 ohm on resistance limits insertion loss, while matching within 5 ohm helps maintain consistency as the selected channel changes. The 150 ns switching time supports rapid acquisition of changing sensor outputs. Place input and common traces away from address lines to reduce switching transients coupling into the measurement path.

🏭

Industrial Sensor Interface

The MAX309EPE+ is appropriate for industrial systems that route multiple sensor outputs into a shared signal-conditioning channel. Its industrial temperature grade supports equipment operating beyond consumer-temperature conditions, while the dual 4:1 arrangement allows two independent four-source groups. On resistance below 100 ohm and channel matching within 5 ohm help limit gain-dependent errors caused by source selection. The break-before-make switching behavior reduces overlap between adjacent inputs during transitions. Designers should verify external signal amplitudes against the supported ±5 V to ±30 V and ±20 V ranges before connecting sensors.

🧰

Precision Test and Measurement

The MAX309EPE+ can route test points, reference levels, or calibration signals in precision measurement equipment. Channel-to-channel on-resistance matching within 5 ohm and variation of no more than 7 ohm across the analog range support repeatable measurements when different sources share the same amplifier or converter input. Two independently controlled 4:1 circuits can also implement differential or complementary selection paths. The 150 ns switching characteristic allows the acquisition system to change sources quickly. Keep the analog traces short and shield them from address and enable transitions to preserve measurement integrity.

🔧

Control Signal Routing

The MAX309EPE+ can select control or feedback signals from multiple circuit locations and direct them to a common controller input. Its less than 100 ohm on resistance is suitable for many low-power control paths, while the 150 ns switching time permits rapid changes in command selection. The dual 4:1 structure reduces component count when two independent groups of control lines must be routed. Break-before-make operation helps prevent two outputs from driving a node simultaneously. Validate the logic levels, supply configuration, and allowed analog range against the manufacturer data sheet before implementation.

📡

Analog Signal Fan-Out

The MAX309EPE+ can combine source selection and analog distribution in equipment with multiple measurement chains. Each 4:1 circuit provides a controlled route from four analog inputs to one common node, allowing a single shared conversion or amplification path to serve multiple sources. Flat on resistance across the specified signal range helps prevent channel-dependent amplitude changes. The approximately 750 pA leakage figure and low on resistance are particularly useful when working with higher-impedance circuits. Use guarding and short analog traces where leakage and leakage-induced errors could affect the source impedance.

🌐

Audio and Communication Routing

The MAX309EPE+ is suitable for routing modest-level analog signals in communication and audio test systems where channel matching matters more than very low distortion specifications. Its within-5-ohm on-resistance matching helps reduce channel-to-channel gain variation, and the dual 4:1 organization supports two related signal paths. The 150 ns transition time is adequate for many source-selection stages. Avoid using the device outside the documented analog and supply ranges, and place the multiplexer away from high-current switching nodes. Add local supply bypassing and avoid routing multiplexed signals next to clock or address lines.

ملخص المنتجات الموصى بها

MAX309EPE+ Analog Devices يُستخدم في: Data-Acquisition Signal Selection, Industrial Sensor Interface, Precision Test and Measurement, Control Signal Routing, Analog Signal Fan-Out, Audio and Communication Routing MAX309CPE+ Commercial-grade family option يُستخدم في: Data-Acquisition Signal Selection, Precision Test and Measurement, Analog Signal Fan-Out MAX309EPE Same-family through-hole option يُستخدم في: Industrial Sensor Interface, Control Signal Routing, Audio and Communication Routing
What is the MAX309EPE+?
The MAX309EPE+ is a dual 4:1 precision CMOS analog multiplexer from Analog Devices. It contains two independent 4:1 switching circuits in a 16-pin PDIP package. According to the Analog Devices MAX309 product page, its on resistance is less than 100 ohm, channel matching is within 5 ohm, and resistance remains flat to within 7 ohm over the specified analog signal range.
What is the on-resistance of MAX309EPE+?
The MAX309EPE+ has an on resistance of less than 100 ohm. The Analog Devices MAX309 product page also states that on-resistance matching between channels is maintained within 5 ohm and that variation across the specified analog signal range is no more than 7 ohm. These figures make the device appropriate for routing moderate-level analog signals where insertion resistance and channel balance are important.
How fast is the MAX309EPE+ analog switch?
The MAX309EPE+ has a stated switching time of 150 ns. According to the Analog Devices MAX309 product page, the MAX308 and MAX309 families are precision monolithic CMOS multiplexers designed for high-performance signal routing. The 150 ns figure indicates fast transition between analog paths, while the break-before-make characteristic prevents two switched inputs from being connected simultaneously during transition.
What package and pin count does MAX309EPE+ use?
The MAX309EPE+ uses a 16-pin PDIP package with a 7.62 mm pitch and through-hole mounting. The Analog Devices product listing identifies the MAX309 family as an 8-channel or dual 4-channel multiplexer, while the distributor specification identifies the MAX309EPE+ as two 4:1 circuits. Use the manufacturer pin-description table when assigning PCB tracks and connector assignments.
Where can I download the MAX309EPE+ datasheet PDF?
The official MAX309EPE+ documentation is available through the Analog Devices MAX309 product page at https://www.analog.com/en/products/max309.html. That page provides the manufacturer data sheet and product resources for the MAX308 and MAX309 families. Use the manufacturer diagram as the authority for pin names, address logic, supply connections, and recommended operating conditions.
Where can I find the MAX309EPE+ pinout?
The MAX309EPE+ pinout is shown in the manufacturer documentation linked from the Analog Devices MAX309 product page. The component has 16 pins in a PDIP footprint, but this page does not reproduce the complete numbered diagram. Use the pin-description table in the MAX309 datasheet to assign enable, address, common, analog-input, supply, and ground connections before laying out the board.
Can MAX309CPE+ replace MAX309EPE+?
The MAX309CPE+ is a same-family, same-package candidate for the MAX309EPE+ because both use the MAX309 dual 4:1 architecture and 16-pin PDIP format. The principal qualification difference is temperature grade: MAX309EPE+ is industrial, while the C designation on MAX309CPE+ denotes a commercial-grade ordering option. Confirm the complete temperature range, supply limits, and pin assignments before substitution.
What is the difference between MAX309EPE+ and MAX309EPE?
The MAX309EPE+ and MAX309EPE belong to the same MAX309 dual 4:1 family and use the same 16-pin PDIP footprint, while the plus designation denotes the later ordering designation used for the lead-free product option. The Analog Devices family description confirms that the MAX309 uses less than 100 ohm on resistance with matching within 5 ohm. Verify the purchasable suffix, temperature grade, and lifecycle status against the manufacturer ordering information.
When should I choose MAX309EPE+ over MAX309CPE+?
Choose MAX309EPE+ when the design requires the industrial-temperature ordering option of the MAX309 dual 4:1 multiplexer in a 16-pin PDIP package. Choose MAX309CPE+ when the commercial-grade ordering option is appropriate for the product's ambient-temperature requirements. Both parts share the same core switching architecture, less than 100 ohm on resistance, and 150 ns switching time.
Is MAX309EPE+ suitable for data-acquisition and instrumentation systems?
The MAX309EPE+ is suitable for instrumentation and data-acquisition systems that must route several analog sources into a common measurement channel. Its dual 4:1 organization supports two independent routing sections, while less than 100 ohm on resistance limits insertion loss. The within-5-ohm channel matching and 150 ns switching time help maintain accuracy and response when selecting among sensor or test signals.
What is the best drop-in replacement for MAX309EPE+?
The closest documented drop-in candidates are the same-family MAX309CPE+ and MAX309EPE in the 16-pin PDIP package. Their core MAX309 dual 4:1 architecture provides a direct functional match, but qualification and ordering suffixes must be checked for temperature grade and lead-free status. No cross-brand part was established as a verified same-footprint replacement in the available cross-reference records.
Is DG409DJ a drop-in replacement for MAX309EPE+?
The available records identify DG409DJ as a comparison candidate, but they do not establish it as a same-package, pin-to-pin replacement for the 16-pin PDIP MAX309EPE+. The MAX309EPE+ has a dual 4:1 architecture, less than 100 ohm on resistance, and a 150 ns switching specification. Verify the DG409DJ package, channel count, address logic, pinout, voltage limits, and switching specifications before considering a PCB substitution.
Where can I buy MAX309EPE+ and check its lead time?
Use the Request a Quote form on this page to request MAX309EPE+ availability, commercial terms, and a current lead-time commitment. The manufacturer identifies the MAX309 as a production product, and distributor listings include the exact MAX309EPE+ ordering code. The Request a Quote response should confirm the package format, quantity, and production scheduling for the current order.
Is MAX309EPE+ in stock?
Current stock status should be confirmed through the Request a Quote form on this page because availability can change with production scheduling and order quantity. The Analog Devices product page identifies the MAX309 as a production device, while distributor records list the MAX309EPE+ specifically. Submit the required quantity, package format, and delivery target to obtain a current allocation response.
What is the price of MAX309EPE+?
The current commercial price for MAX309EPE+ should be requested through the Request a Quote form on this page. The structured pricing interface accounts for currency, quantity, and channel conditions, so a static figure would not represent a dependable quotation. Include the required quantity and whether the delivery format must be a tube to receive a precise purchasing response.
What are the key specifications of MAX309EPE+ that engineers should know?
The key MAX309EPE+ specifications are its dual 4:1 configuration, two internal circuits, less than 100 ohm on resistance, within-5-ohm channel matching, maximum 7-ohm resistance variation across the analog range, 150 ns switching time, approximately 750 pA leakage current, and 16-pin PDIP package. According to the Analog Devices MAX309 product page, break-before-make operation also prevents unintended overlap during channel transition.

بيانات مرجعية هندسية لـ MAX309EPE+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose MAX309EPE+ for industrial equipment requiring two independent 4:1 analog routing sections in a through-hole 16-pin PDIP package. Its less than 100 ohm on resistance, within-5-ohm channel matching, break-before-make switching, and 150 ns switching time make it appropriate for instrumentation, sensor routing, and test systems. Choose MAX309CPE+ when the same electrical and package architecture is needed but the product falls within commercial-temperature requirements. Choose MAX309EPE when an earlier ordering designation is acceptable and the required qualification and lifecycle conditions are confirmed. No cross-brand alternative should be installed without verifying its package, pinout, address logic, channel architecture, voltage limits, and switching specifications because the available comparison records do not establish a verified same-footprint substitute.

المقارنة مع البدائل

المعامل هذا المنتج MAX309CPE+ MAX309EPE
Package 16-PDIP 16-PDIP 16-PDIP
Brand Analog Devices Analog Devices Analog Devices
Multiplexer Configuration Dual 4:1 Dual 4:1 Dual 4:1
Number of Circuits 2 circuits 2 circuits 2 circuits
Temperature Grade Industrial Commercial Industrial

أبرز الفروقات

  • Industrial-temperature ordering option (مقابلMAX309CPE+)
  • Two independent 4:1 sections in one package (مقابلMAX309EPE)
  • Matched, low-resistance channel behavior (مقابلMAX309EPE)

ملاحظات التصميم

Route each analog input and common output directly to its multiplexer pin with short traces and minimal vias. The MAX309EPE+ uses a through-hole 16-pin PDIP footprint, so place the device near the signal source and receiving circuit rather than centralizing it on a large board. Keep address and enable traces away from the analog paths, and avoid routing these paths beneath digital clock, switching-regulator, or high-current return traces.

Do not assume that the MAX309EPE+ can accept every signal encountered at its common pins. The family operates from a 5 V supply and supports specified analog ranges that include ±5 V to ±30 V and ±20 V, depending on the operating configuration. Check the maximum signal amplitude, supply arrangement, and control-state limits in the manufacturer data sheet before applying external voltages. Also preserve break-before-make operation by following the specified address-change procedure.

On resistance is below 100 ohm and channel matching is within 5 ohm, but source impedance, leakage, and trace capacitance can still influence system accuracy. For high-impedance sources, account for approximately 750 pA of leakage and use guarding where necessary. Keep the common node short, maintain symmetric routing between related channels, and place any required input or bypass capacitors close to the associated device pins to limit parasitic effects.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The plus designation identifies the lead-free ordering option, but no explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals statement appears in the cited product information.

تم التحقق من البيانات في: 2026-11-14 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MAX309EPE+ datasheet MAX309EPE+ datasheet pdf MAX309EPE+ pinout MAX309EPE+ equivalent MAX309EPE+ replacement MAX309EPE+ cross reference MAX309EPE+ vs MAX309CPE+ Analog Devices MAX309EPE+ MAX309EPE+ 16-DIP multiplexer MAX309EPE+ dual 4:1 switch MAX309EPE+ on resistance MAX309EPE+ data acquisition MAX309EPE+ price MAX309EPE+ stock MAX309EPE+ application circuit

المكونات والمصطلحات ذات الصلة

Analog Devices MAX309EPE+ MAX309CPE+ MAX309EPE MAX309 CMOS analog multiplexer analog switch interface IC semiconductor dual 4:1 multiplexer break-before-make switching on resistance channel matching switching time leakage current 16-PDIP PDIP package family through-hole mount data acquisition industrial sensor interface test and measurement analog signal routing industrial temperature grade RoHS REACH
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر