MAX309EPE+ - Dual 4:1 CMOS Multiplexer | Analog Devices
料号: MAX309EPE+ ✓ 量产中MAX309EPE+ 概述
A CMOS analog multiplexer is an interface IC that routes one of several input signals to a shared output under digital control. The MAX309 belongs to the analog switch and multiplexer hierarchy, where it combines bidirectional signal routing, low on resistance, and precise channel matching. Each internal 4:1 circuit uses address logic to select one of four analog inputs for connection to its common output.
Key characteristics include on resistance below 100 ohm, channel-to-channel matching within 5 ohm, and on-resistance variation of no more than 7 ohm across the specified analog signal range. The device also provides break-before-make operation and approximately 750 pA of leakage-related current in the cited technical listing. These characteristics support accurate routing of moderate-voltage analog signals without introducing substantial insertion resistance.
The MAX309EPE+ is implemented as a precision monolithic CMOS device, with two independently addressed 4:1 sections. Its 150 ns switching figure supports applications requiring fast selection among sensors, measurement channels, or control signals. Matching between channels and flat on resistance across the analog range help preserve signal amplitude and balance when different sources are selected.
Typical uses include instrumentation signal selection, data-acquisition systems, industrial control interfaces, test and measurement equipment, and analog signal routing where several sources share a common processing chain. The dual-circuit organization can route two independent signal groups or provide two complementary multiplexed paths on the same board.
PCB design should preserve the 16-pin PDIP footprint and route each analog input directly to its intended pin. Keep sensitive analog traces away from digital address and control lines, provide clean supply decoupling, and use short connections to minimize parasitic capacitance. Verify the selected supply and input ranges against the MAX309 datasheet before connecting external signals.
This page combines manufacturer product information, distributor listings, same-family drop-in candidates, application guidance, and practical design notes to support component selection and PCB implementation.
直接替换替代料: MAX309EPE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MAX309CPE+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX309EPE
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX309EPE+ 规格参数
| Multiplexer Configuration | Dual 4:1 |
| Number of Circuits | 2 circuits |
| On Resistance | Less than 100 ohm |
| On-Resistance Matching Between Channels | Within 5 ohm |
| On-Resistance Variation Across Signal Range | 7 ohm maximum |
| Switching Time | 150 ns |
| Leakage Current | 750 pA |
| Signal Voltage Range | ±5 V to ±30 V and ±20 V |
| 电源电压 | 5 V |
| Switching Behavior | Break-before-make |
| Technology | Precision monolithic CMOS |
| Temperature Grade | Industrial |
| 封装 | 16-pin PDIP |
| Package Pitch | 7.62 mm |
| 安装类型 | Through-hole |
| Shipping Format | Tube |
MAX309EPE+ 7.62 mm 引脚配置指南
MAX309EPE+(7.62 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX309EPE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX309EPE+ 适用于 6 应用s: Data-Acquisition Signal Selection, Industrial Sensor Interface, Precision Test and Measurement, Control Signal Routing, Analog Signal Fan-Out, Audio and Communication Routing.
Data-Acquisition Signal Selection
The MAX309EPE+ fits data-acquisition boards that must select among several analog inputs while preserving signal amplitude and balance. Its two independent 4:1 sections can route two groups of four sources, reducing the number of separate multiplexers needed on the board. Less than 100 ohm on resistance limits insertion loss, while matching within 5 ohm helps maintain consistency as the selected channel changes. The 150 ns switching time supports rapid acquisition of changing sensor outputs. Place input and common traces away from address lines to reduce switching transients coupling into the measurement path.
推荐
Industrial Sensor Interface
The MAX309EPE+ is appropriate for industrial systems that route multiple sensor outputs into a shared signal-conditioning channel. Its industrial temperature grade supports equipment operating beyond consumer-temperature conditions, while the dual 4:1 arrangement allows two independent four-source groups. On resistance below 100 ohm and channel matching within 5 ohm help limit gain-dependent errors caused by source selection. The break-before-make switching behavior reduces overlap between adjacent inputs during transitions. Designers should verify external signal amplitudes against the supported ±5 V to ±30 V and ±20 V ranges before connecting sensors.
推荐
Precision Test and Measurement
The MAX309EPE+ can route test points, reference levels, or calibration signals in precision measurement equipment. Channel-to-channel on-resistance matching within 5 ohm and variation of no more than 7 ohm across the analog range support repeatable measurements when different sources share the same amplifier or converter input. Two independently controlled 4:1 circuits can also implement differential or complementary selection paths. The 150 ns switching characteristic allows the acquisition system to change sources quickly. Keep the analog traces short and shield them from address and enable transitions to preserve measurement integrity.
推荐
Control Signal Routing
The MAX309EPE+ can select control or feedback signals from multiple circuit locations and direct them to a common controller input. Its less than 100 ohm on resistance is suitable for many low-power control paths, while the 150 ns switching time permits rapid changes in command selection. The dual 4:1 structure reduces component count when two independent groups of control lines must be routed. Break-before-make operation helps prevent two outputs from driving a node simultaneously. Validate the logic levels, supply configuration, and allowed analog range against the manufacturer data sheet before implementation.
推荐
Analog Signal Fan-Out
The MAX309EPE+ can combine source selection and analog distribution in equipment with multiple measurement chains. Each 4:1 circuit provides a controlled route from four analog inputs to one common node, allowing a single shared conversion or amplification path to serve multiple sources. Flat on resistance across the specified signal range helps prevent channel-dependent amplitude changes. The approximately 750 pA leakage figure and low on resistance are particularly useful when working with higher-impedance circuits. Use guarding and short analog traces where leakage and leakage-induced errors could affect the source impedance.
推荐
Audio and Communication Routing
The MAX309EPE+ is suitable for routing modest-level analog signals in communication and audio test systems where channel matching matters more than very low distortion specifications. Its within-5-ohm on-resistance matching helps reduce channel-to-channel gain variation, and the dual 4:1 organization supports two related signal paths. The 150 ns transition time is adequate for many source-selection stages. Avoid using the device outside the documented analog and supply ranges, and place the multiplexer away from high-current switching nodes. Add local supply bypassing and avoid routing multiplexed signals next to clock or address lines.
推荐
推荐产品汇总
工程参考数据: MAX309EPE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX309CPE+ | MAX309EPE |
|---|---|---|---|
| Package | 16-PDIP | 16-PDIP | 16-PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| Temperature Grade | Industrial | Commercial | Industrial |
关键差异点
- Industrial-temperature ordering option (对比 MAX309CPE+)
- Two independent 4:1 sections in one package (对比 MAX309EPE)
- Matched, low-resistance channel behavior (对比 MAX309EPE)
设计说明
Route each analog input and common output directly to its multiplexer pin with short traces and minimal vias. The MAX309EPE+ uses a through-hole 16-pin PDIP footprint, so place the device near the signal source and receiving circuit rather than centralizing it on a large board. Keep address and enable traces away from the analog paths, and avoid routing these paths beneath digital clock, switching-regulator, or high-current return traces.
Do not assume that the MAX309EPE+ can accept every signal encountered at its common pins. The family operates from a 5 V supply and supports specified analog ranges that include ±5 V to ±30 V and ±20 V, depending on the operating configuration. Check the maximum signal amplitude, supply arrangement, and control-state limits in the manufacturer data sheet before applying external voltages. Also preserve break-before-make operation by following the specified address-change procedure.
On resistance is below 100 ohm and channel matching is within 5 ohm, but source impedance, leakage, and trace capacitance can still influence system accuracy. For high-impedance sources, account for approximately 750 pA of leakage and use guarding where necessary. Keep the common node short, maintain symmetric routing between related channels, and place any required input or bypass capacitors close to the associated device pins to limit parasitic effects.
合规信息
The plus designation identifies the lead-free ordering option, but no explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals statement appears in the cited product information.