MAX310MJE - 8:1 CMOS RF/Video Multiplexer | Analog Devices
MPN: MAX310MJE ✓ نشطMAX310MJE نظرة عامة
An RF/video multiplexer is an analog switch that connects one common signal path to any one of several signal inputs. It belongs to the analog switch hierarchy, which includes multiplexers and demultiplexers, and ultimately falls under interface ICs and semiconductor signal-routing devices. The MAX310MJE consolidates eight selectable sources onto one output, reducing the number of discrete switches and associated routing logic required in video, test, instrumentation, and communications equipment.
Key characteristics include an 8:1 configuration, CMOS construction, 16-CDIP mechanical format, through-hole mounting, and maximum on-state resistance of 250 ohms. Its military temperature grade makes it relevant to ruggedized equipment, although the exact operating-temperature limits should be confirmed against the manufacturer datasheet before a production release. The unbuffered architecture places important emphasis on external source and load impedance, signal amplitude, switching time, and off-state isolation.
The MAX310MJE uses independent selection and enable controls to route one of eight channels to the common terminal. Because the switch is unbuffered, it does not provide gain, isolation, impedance buffering, or level translation. Designers should therefore evaluate source impedance, receiver capacitance, settling time, insertion loss, off leakage, and crosstalk together. A practical video path benefits from short traces, a stable ground reference, and termination arranged to minimize reflections.
Typical uses include RF and video test systems, instrumentation signal routing, communication equipment, broadcast video interfaces, and defense or aerospace electronics. The part can also support channel-selection architectures where a controller chooses among several inputs and a common amplifier or measurement channel processes the selected signal. Its through-hole CDIP package favors systems that favor through-hole assembly, rugged handling, or prototyping over compact surface-mount layouts.
The principal design consideration is signal integrity. Keep input and common-path traces short, use a continuous ground plane, and place the multiplexer near the source of unwanted impedance. Avoid long unterminated traces that can amplify reflections and degrade settling behavior. Review break-before-make requirements in the control timing before switching adjacent channels, especially where the upstream circuit must remain undisturbed during transition.
This product overview combines the MAX310MJE configuration, package, resistance, temperature-grade information, and application guidance with pin-compatible alternatives and practical routing considerations. It supports faster sourcing and design decisions while keeping electrical verification anchored in the manufacturer datasheet.
بدائل مباشرة لـ MAX310MJE — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MAX310MJE (نفس عامل الشكل والبصمة) — يختلف في Product Type.
MAX310MJE/883B
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX310CPE+
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←5962-9455601MEA
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX310MJE المواصفات
| Product Type | 8:1 CMOS RF/video multiplexer |
| Multiplexer Configuration | Single 8:1 |
| Number of Signal Channels | 1 channel |
| Technology | CMOS |
| Architecture | Unbuffered analog multiplexer |
| On-State Resistance | 250 ohms maximum |
| Package Type | 16-pin CDIP |
| Package Code | CDIP |
| نوع التركيب | Through-hole |
| Pin Pitch | 0.300 inch (7.62 mm) |
| Number of Terminals | 16 |
| Temperature Grade | Military |
| Surface Mount | No |
دليل تكوين أطراف MAX310MJE cdip
تكوين الأطراف لـ MAX310MJE (حزمة cdip). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX310MJE.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX310MJE مناسب لـ 6 التطبيقs: RF Test-System Signal Routing, Video Channel Selection, Communication Equipment Routing, Aerospace Signal-Selection Systems, Instrumentation Signal Multiplexing, Broadcast Video Patch Systems.
RF Test-System Signal Routing
The MAX310MJE fits an eight-source RF test multiplexer because it provides a single 8:1 common-output path in a 16-pin CDIP package with maximum on-state resistance of 250 ohms. It can route one of eight test inputs into a common receiver, attenuator, or measurement channel without requiring eight separate external switches. The military temperature grade is also relevant to rugged test equipment. Because the device is unbuffered, source impedance, receiver capacitance, insertion loss, and settling time must be checked in the manufacturer datasheet. Keep the common path short and provide a low-impedance ground reference to limit RF coupling and reflections.
موصى به
Video Channel Selection
The MAX310MJE is suitable for selecting one of eight video sources onto a common video path. Its 8:1 CMOS topology reduces the routing complexity of multi-camera, multi-source, or laboratory video equipment, while the 250-ohm maximum on-state resistance provides a defined basis for impedance matching. Since the multiplexer is unbuffered, video amplitude, source impedance, cable capacitance, and receiver loading remain important. Route the common output as a short, continuously referenced trace and confirm allowable input swing and settling requirements in the Analog Devices datasheet.
موصى به
Communication Equipment Routing
The MAX310MJE can serve as a compact eight-way RF or video routing element within communication equipment that must connect several controlled sources to one processing chain. Its single 8:1 configuration supports source selection without duplicating downstream amplifiers or converters. The 16-CDIP through-hole package is advantageous for ruggedized or laboratory communication hardware where through-hole assembly and serviceability are priorities. Designers should verify operating frequency, channel isolation, off-state rejection, control timing, and supply voltage in the MAX310 datasheet before establishing signal-integrity margins.
موصى به
Aerospace Signal-Selection Systems
The MAX310MJE's military temperature grade and 8:1 RF/video multiplexing function make it a candidate for aerospace and defense signal-selection assemblies where one channel must be routed to a common receiver or processor. The 16-pin CDIP package supports through-hole assembly in ruggedized equipment. Qualification requirements still govern the final choice, so MAX310MJE/883B or 5962-9455601MEA may be preferable when screened procurement is required. Review radiation, environmental, reliability, and continuous-operating-life requirements separately from the device's commercial electrical ratings.
موصى به
Instrumentation Signal Multiplexing
The MAX310MJE allows eight measurement or stimulus sources to share one analog processing path in a laboratory instrument. The common output can feed an amplifier, converter, or acquisition channel while selection logic chooses the active source. Its maximum on-state resistance of 250 ohms makes source and load impedance particularly important, and unbuffered operation does not provide gain or isolation. Use short traces, a stable ground plane, and intentional termination, then verify input capacitance, leakage, switching speed, and crosstalk in the manufacturer datasheet.
موصى به
Broadcast Video Patch Systems
The MAX310MJE can route one of eight video inputs into a common broadcast or monitoring path, reducing the number of mechanical or discrete switching elements in a patch system. Its 8:1 CMOS architecture and military-grade designation suit professional equipment requiring controlled source selection. The 16-CDIP package is through-hole mounted with a 7.62 mm pitch, supporting rugged assembly. Because the switch is unbuffered, long cable runs and high-capacitance receivers should be checked for settling and reflection problems, with the common trace kept as short as practical.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX310MJE — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX310MJE/883B | MAX310CPE+ | 5962-9455601MEA |
|---|---|---|---|---|
| Package | 16-pin CDIP | 16-pin CDIP | 16-pin CDIP | 16-pin CDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | Single 8:1 | 8:1 unbuffered | 8:1 | 8:1 |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
أبرز الفروقات
- Closest screened ordering option (مقابلMAX310MJE/883B)
- Military-grade standard ordering configuration (مقابلMAX310CPE+)
- Defined maximum on-state resistance (مقابل5962-9455601MEA)
ملاحظات التصميم
Treat the common path as a transmission line rather than an ideal wire. The 250-ohm maximum on-state resistance interacts with source impedance, receiver capacitance, and trace inductance, especially at higher RF frequencies. Keep the selected input, common terminal, and ground return physically short, provide a continuous ground reference, and use the manufacturer's recommended termination arrangement. Validate channel settling with the actual source and load because an unbuffered switch does not restore signal integrity.
Use the 16-pin CDIP footprint with a 0.300-inch, 7.62 mm pitch and verify pin-one orientation against the MAX310 manufacturer datasheet before drilling. Maintain adequate clearance around the package for the external control logic and analog routing. Place decoupling close to the device's supply and ground pins in the pattern recommended by the datasheet, and avoid routing unrelated digital clocks beneath the analog common path to reduce coupled noise.
Do not treat the MAX310MJE as a gain or isolation buffer. Its unbuffered architecture can load the source, interact with downstream capacitance, and expose the signal to crosstalk and switching transients. Confirm control logic polarity, break-before-make behavior, maximum signal swing, supply limits, and allowed switching rates in the datasheet. For adjacent-channel systems, hold the inactive channel in a defined state to prevent unintended signal contention.
Minimize radiated and conducted coupling by keeping the RF or video common path away from switching-power nodes and high-current returns. Use a solid ground plane, short ground connections, and a defined return path beneath the analog route where the board stack-up permits. If the selected signal has wide bandwidth, check adjacent-channel isolation and off-state rejection with realistic terminations; long cable or harness interfaces can dominate crosstalk even when the IC itself performs within its ratings.
معلومات الامتثال
The MAX310MJE is identified as military-temperature grade and has a 5962-style alternative, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement appears in the product information. AEC-Q100 is not applicable to this legacy analog multiplexer based on the stated military qualification.