MAX3221ECUE+T - 250kbps RS-232 Transceiver | Analog Devices
MPN: MAX3221ECUE+T ✓ نشطMAX3221ECUE+T نظرة عامة
An RS-232 transceiver is an interface IC that converts logic-level UART signals between a host controller and a cable-based RS-232 port. It belongs to the RS-232 transceiver category, which sits within the broader hierarchy of interface ICs, communication semiconductors, and discrete analog-and-digital interface components. Unlike logic-level UART links, the RS-232 side uses bipolar voltage levels and requires controlled edge rates to meet communication and electromagnetic-interference requirements.
The MAX3221ECUE+T combines a transmitter and receiver in one compact package. Key features include operation from 3.0V to 5.5V, data rates up to 250kbps, ±15kV ESD protection, and a low 1µA shutdown supply current. Its AutoShutdown function reduces power consumption when the receiver does not detect a valid signal. These characteristics make it useful where energy use, board area, and port reliability are important.
Maxim's charge-pump architecture generates the positive and negative voltages required by the RS-232 transmitter while the device operates from a single low-voltage supply. Four small external capacitors support this function. The integrated transmitter adds controlled signal shaping, while the receiver translates the bipolar RS-232 input into a CMOS-compatible logic level for the host UART. Automatic wakeup supports systems that periodically power their communications port.
Typical uses include industrial control equipment, point-of-sale terminals, instrumentation, maintenance equipment, and embedded serial-port adapters. The device is also appropriate for portable or industrial systems that need a single RS-232 channel rather than the multiple drivers and receivers offered by larger interface families. A 3.3V system can use the same part as a 5V system, subject to the external interface and logic-level requirements of the connected controller.
PCB layout is critical because the charge-pump capacitors must be placed close to their associated pins, while the RS-232 connector path should remain as short and separated from sensitive circuitry as practical. Keep the connector-side return path continuous, route driver and receiver traces away from switching nodes, and use the device pin-description table when assigning connector and logic nets.
This product record combines device specifications, verified source links, package information, application guidance, and engineering-focused comparisons. It also identifies genuine same-package alternatives and explains when their electrical or qualification differences matter, helping designers evaluate replacement options without overlooking board-layout or operating constraints.
بدائل مباشرة لـ MAX3221ECUE+T — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MAX3221ECUE+T (نفس عامل الشكل والبصمة) — يختلف في ESD Protection, Maximum Data Rate, Power Management, Supply Voltage Range.
MAX3221EUE+T
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3221EEUE+T
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3221CPWE4
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3221ECUE+T المواصفات
| Product Type | Single-channel RS-232 transceiver |
| Transmitter Count | 1 driver |
| Receiver Count | 1 receiver |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | 250kbps |
| ESD Protection | ±15kV |
| Shutdown Supply Current | 1µA |
| Power Management | AutoShutdown with automatic wakeup |
| Interface Standard | EIA/TIA-232 and V.28/V.24 |
| العلبة | 16-pin TSSOP |
| نوع التركيب | Surface mount |
| External Charge-Pump Capacitors | 4 capacitors |
| Operating Voltage | 3.0V to 5.5V |
| Data-Rate Class | Up to 250kbps |
| ESD Interface Protection | ±15kV on RS-232 pins |
دليل تكوين أطراف MAX3221ECUE+T 16-pin tssop
تكوين الأطراف لـ MAX3221ECUE+T (حزمة 16-pin tssop). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX3221ECUE+T.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX3221ECUE+T مناسب لـ 6 التطبيقs: Industrial Control and Instrumentation, Portable Test and Measurement Equipment, Point-of-Sale and Service Terminals, Embedded Serial Port Adapter, Maintenance and Diagnostic Equipment, Communication Port Isolation in Control Systems.
Industrial Control and Instrumentation
The MAX3221ECUE+T fits a single RS-232 connection on a compact industrial controller because it combines one driver, one receiver, and a 3.0V to 5.5V supply in a 16-pin TSSOP package. Its 250kbps maximum data rate supports responsive command and telemetry traffic, while ±15kV ESD protection strengthens the cable-facing interface. AutoShutdown reduces standby supply current to approximately 1µA when no valid receiver activity is present. In a typical circuit, the host UART connects to the logic-side pins and the RS-232 lines connect to the external DB9 or terminal connector. Keep the charge-pump capacitors close to the IC and route the connector path away from sensitive analog circuitry.
موصى به
Portable Test and Measurement Equipment
The MAX3221ECUE+T is well suited to handheld meters, bench accessories, and portable service tools that communicate through an RS-232 port. The 3.0V to 5.5V operating range permits use with 3.3V or 5V system rails, and the 16-pin TSSOP package limits board area. Automatic shutdown is particularly useful for instruments that remain connected to equipment but spend substantial time without valid RS-232 traffic, since the cited shutdown current is approximately 1µA. A system designer can place the transceiver between the UART controller and connector, retain the four required charge-pump capacitors, and use the ±15kV-protected RS-232 pins for a replaceable cable. Verify connector pin assignments and grounding independently because the integrated IC does not determine the mechanical DB9 wiring.
موصى به
Point-of-Sale and Service Terminals
The MAX3221ECUE+T can provide a compact serial port in point-of-sale terminals, receipt printers, and service consoles that need one RS-232 channel. A 250kbps data rate is suitable for command traffic and moderate diagnostic data, while the single-supply 3.0V to 5.5V range simplifies compatibility with embedded logic running at 3.3V or 5V. The transmitter and receiver are integrated into one 16-pin TSSOP device, reducing component count compared with separate driver and receiver packages. AutoShutdown avoids sustained power consumption when the attached peripheral is disconnected. For reliable operation, place the four external charge-pump capacitors adjacent to the appropriate pins, provide a low-impedance ground route to the connector, and keep the unprotected logic-side traces away from the cable connection.
موصى به
Embedded Serial Port Adapter
The MAX3221ECUE+T is appropriate for a compact serial adapter that adds one legacy RS-232 port to a modern controller board. The 16-pin TSSOP package simplifies routing on a dense interface board, while operation from 3.0V to 5.5V supports both common embedded supply voltages. Its 250kbps maximum rate accommodates configuration downloads, status exchanges, and legacy peripheral traffic without requiring a multi-channel transceiver. AutoShutdown allows the adapter to remain attached to a host while drawing approximately 1µA when no valid signal appears. The implementation should maintain a short RS-232 route to the connector, use a continuous return path, and separate the charge-pump area from sensitive signal traces. Check the UART voltage levels and all 16 pin assignments against the manufacturer pin table during board release.
موصى به
Maintenance and Diagnostic Equipment
The MAX3221ECUE+T supports maintenance equipment that exchanges commands with service ports or diagnostic fixtures over RS-232. The integrated ±15kV ESD protection is useful on a cable-accessible interface, and the 250kbps rate provides adequate throughput for logs, test records, and configuration blocks. Because only one driver and one receiver are present, the device offers a straightforward point-to-point implementation without allocating a larger multi-channel interface. Automatic wakeup permits the host controller to leave the port inactive until peripheral activity resumes. During layout, keep the transceiver close to the connector, provide a direct chassis or signal-ground return, and isolate the cable path from precision measurement circuitry. Environmental sealing and additional surge protection may still be required for installations with severe ESD or transients.
موصى به
Communication Port Isolation in Control Systems
The MAX3221ECUE+T can serve as the cable-facing RS-232 block in a control system requiring separation between a host UART and external equipment. Its 3.0V to 5.5V operation supports low-voltage system rails, while the single-supply charge pump removes the need for a separate bipolar transceiver supply. The receiver and transmitter provide the required logic-to-RS-232 signal conversion, and ±15kV ESD protection improves robustness at a user-accessible connector. AutoShutdown can reduce standby consumption in systems where the remote port is rarely active. For best signal integrity, terminate the charge-pump capacitor loop close to the device, maintain a continuous connector ground, and route the RS-232 conductors away from switching nodes and high-impedance analog inputs. Validate the complete channel against the required system baud rate and cable length.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX3221ECUE+T — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX3221EUE+T | MAX3221EEUE+T | MAX3221CPWE4 |
|---|---|---|---|---|
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Texas Instruments |
| Device Type | Single-channel RS-232 transceiver | Single-channel RS-232 transceiver | Single-channel RS-232 transceiver | RS-232 interface IC |
| Supply Voltage | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.3V device |
أبرز الفروقات
- Single-channel integration in a compact package (مقابلMAX3221CPWE4)
- Automatic low-power operation (مقابلMAX3221EUE+T)
- Broad single-supply compatibility (مقابلMAX3221CPWE4)
ملاحظات التصميم
Place the four charge-pump capacitors close to their corresponding MAX3221ECUE+T pins and use short, direct return paths. Keep the RS-232 driver and receiver traces away from clocks, switching-regulator nodes, and sensitive analog inputs. Route toward the connector without unnecessary stubs, and use the manufacturer pin-description table to verify every connection before release.
Treat the cable connector and its return path as an electrically noisy boundary. Maintain a low-impedance ground connection between the interface ground and connector return, and place the transceiver near the connector where practical. The integrated ±15kV ESD protection helps at the IC pins, but it does not replace connector shielding, enclosure bonding, or system-level surge protection.
AutoShutdown can reduce the transceiver supply current to approximately 1µA when no valid receiver activity is detected. Confirm that the host UART and attached peripheral do not create a false valid level on the receiver input, because such a condition can prevent shutdown. Add the external capacitors required by the charge pump and follow the manufacturer’s recommended capacitance values and tolerance.
معلومات الامتثال
The device is a commercial RS-232 interface IC; no automotive qualification or specific material-compliance declaration was identified in the source information. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-mineral declarations with the current manufacturer documentation before procurement.