MAX3221EUE+TG1Z - 3V RS-232 Transceiver | Analog Devices
MPN: MAX3221EUE+TG1Z ✓ نشطMAX3221EUE+TG1Z نظرة عامة
An RS-232 transceiver is an interface IC that converts logic-level digital signals to RS-232 voltage levels and converts incoming RS-232 signals back to logic levels. The MAX3221E belongs to the broader RS-232 transceiver, line-driver/receiver, communications-interface, and interface-IC hierarchy. Its single-channel arrangement is appropriate when a system needs one serial port rather than multiple RS-232 channels.
The main advantages of the MAX3221E family are its low 3 V supply operation, 250 kbps maximum signaling rate, automatic power management, and enhanced ESD protection. AutoShutdown reduces supply consumption when the receiver does not detect a valid signal, while automatic wake-up restores operation when valid data returns. The manufacturer describes the MAX3221, MAX3223, and MAX3243 as achieving 1 uA supply current with this shutdown mechanism.
The EUE+TG1Z ordering code identifies the MAX3221E device in a 16-pin TSSOP package, with the industrial temperature option and tape-and-reel production form indicated by the ordering suffix. The MAX3221E family supports 3 V-powered EIA/TIA-232 and V.28/V.24 communications interfaces. Its protected receiver and driver outputs are intended for equipment where the external serial port can be exposed to electrostatic discharge or cable transients.
Typical applications include industrial serial consoles, programmable test equipment, point-of-sale terminals, instrument-control links, and embedded systems that retain an RS-232 port. In each case, the transceiver can operate from a 3 V system rail while providing the larger voltage swings required by RS-232. The 250 kbps capability also supports moderately high-speed legacy serial links, although the chosen protocol, cable length, and receiver thresholds remain important system-level constraints.
Designers should follow the manufacturer’s recommended charge-pump capacitor and logic-side bypass-capacitor connections, keep the RS-232 trace route away from sensitive analog or high-speed digital nets, and provide the required protection and grounding strategy at an external connector. The device’s automatic shutdown behavior should also be checked against the system’s idle-state and remote-wakeup expectations.
This page combines the exact orderable MPN, interface characteristics, package information, practical application guidance, and verified comparison context. It also identifies where detailed pin mapping, lifecycle status, and complete alternative-specific electrical limits must be confirmed in the manufacturer datasheet before design release.
بدائل مباشرة لـ MAX3221EUE+TG1Z — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MAX3221EUE+TG1Z (نفس عامل الشكل والبصمة) — يختلف في Maximum Data Rate, Number of Receivers, Supply Voltage Range, Device Type, ESD Protection.
MAX3221EUE+
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3221EAE+TG1Z
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3221EEUE
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3232CUE+
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3232EIPWRQ1
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3238IPWR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3221EUE+TG1Z المواصفات
| Device Type | 1/1 full RS-232 transceiver |
| Number of Transmitters | 1 transmitter |
| Number of Receivers | 1 receiver |
| Supply Voltage Range | +3 V to +5.5 V |
| Maximum Data Rate | 250 kbps |
| Power-Supply Shutdown Current | 1 uA |
| ESD Protection | +/-15 kV IEC-ESD |
| Interface Standard | EIA/TIA-232 |
| Supported Protocol Levels | V.28 and V.24 |
| Power Management Feature | AutoShutdown with automatic wake-up |
| العلبة | 16-pin TSSOP |
| نوع التركيب | Surface mount |
| Temperature Grade | Industrial |
| Terminal Count | 16 terminals |
| Package Family | TSSOP |
دليل تكوين أطراف MAX3221EUE+TG1Z tssop
تكوين الأطراف لـ MAX3221EUE+TG1Z (حزمة tssop). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX3221EUE+TG1Z.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX3221EUE+TG1Z مناسب لـ 6 التطبيقs: Industrial Serial Console, Programmable Test Equipment, Point-of-Sale Terminal, Embedded Instrument Interface, RS-232 Connectivity Hub, Security and Access Controller.
Industrial Serial Console
The MAX3221EUE+TG1Z is suitable for an industrial controller or service console that must retain an RS-232 diagnostic port while operating from a 3.3 V system rail. Its +3 V to +5.5 V supply range supports low-voltage logic systems, and the 250 kbps rate accommodates moderately fast serial links. Automatic shutdown can reduce power when no receiver activity exists, although the host software must tolerate the wake-up sequence. Industrial enclosure grounding, cable transients, and ESD protection around the connector should be reviewed alongside the device’s ±15 kV IEC-ESD rating.
موصى به
Programmable Test Equipment
Test and measurement instruments often need a short-distance control link for legacy instruments, fixture controllers, or service peripherals. The MAX3221EUE+TG1Z provides one full RS-232 channel in a compact 16-pin TSSOP, supports rates up to 250 kbps, and can operate from the same 3.3 V rail as the instrument’s digital control logic. Its automatic shutdown behavior helps avoid unnecessary transceiver activity between commands. Keep the serial trace short, observe the required charge-pump capacitors, and validate the complete command protocol across the selected cable length before release.
موصى به
Point-of-Sale Terminal
A point-of-sale terminal or peripheral interface can use the MAX3221EUE+TG1Z for an RS-232 printer, scanner, or customer-display link. The device reduces the external footprint by integrating one driver, one receiver, charge-pump support, and ESD protection into a 16-pin TSSOP. Operation from +3 V to +5.5 V lets the interface share a common system rail, while the 250 kbps capability is more than adequate for many legacy peripheral protocols. Confirm AutoShutdown timing against the peripheral’s request/response behavior to prevent missed wake-up or partial-character conditions.
موصى به
Embedded Instrument Interface
The MAX3221EUE+TG1Z is useful in embedded laboratory and industrial instruments that expose a configuration or service port over RS-232. A 3.3 V embedded controller can communicate through the transceiver without adding a separate 5 V interface rail, and the automatic shutdown function reduces current during idle periods. The 250 kbps capability supports efficient firmware download or diagnostic traffic. Because the exact pin mapping is not reproduced in the product listing, the PCB should be assigned from the manufacturer pin-description table and checked against the selected charge-pump network.
موصى به
RS-232 Connectivity Hub
A connectivity or maintenance hub that must bridge a host UART to an RS-232 peripheral can place the MAX3221EUE+TG1Z beside the host processor. The transceiver converts the processor’s logic-level UART signals to RS-232 levels and returns received data to the host, while automatic shutdown and wake-up reduce power during idle periods. The 16-pin TSSOP package supports compact PCB layouts, but the layout must preserve the charge-pump capacitor loop and keep the RS-232 nets isolated from sensitive digital signals. Verify the host UART logic levels and the peripheral’s cable-grounding arrangement.
موصى به
Security and Access Controller
Access-control and security equipment can use the MAX3221EUE+TG1Z for a wired maintenance or credential-reader interface. The integrated ±15 kV IEC-ESD protection adds useful robustness for a connector that may be touched during installation, while the 3 V to 5.5 V operating range supports compact embedded systems. The automatic shutdown behavior is valuable in low-power installations, but controller firmware should maintain the receiver in a state that permits expected wake-up events. External surge protection and enclosure bonding may still be needed for installations exposed to severe electrical environments.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX3221EUE+TG1Z — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX3221EUE | MAX3221EAE+TG1Z | MAX3232CUE+ | MAX3232EIPWR | MAX3238IPWR |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Transmitter/Receiver Count | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver |
أبرز الفروقات
- Single-channel RS-232 operation with 3 V supply support (مقابلMAX3232CUE+)
- High-rate single-channel interface (مقابلMAX3238IPWR)
- Enhanced connector-side ESD protection (مقابلMAX3232EIPWR)
ملاحظات التصميم
Place all charge-pump capacitors and the supply bypass capacitor directly beside their associated MAX3221EUE+TG1Z pins. Keep each capacitor’s connection to the device short, and use the capacitor values and PCB-land pattern shown in the manufacturer’s typical application circuit. Avoid routing the charge-pump nodes beneath the TSSOP or between sensitive signal traces, because switching current can couple into adjacent circuitry.
Route the RS-232 receiver and driver nets as a protected interface, keeping them away from clocks, ADC inputs, crystal circuits, and other high-impedance analog nodes. Terminate exposed connector-side nets with the protection strategy appropriate to the installation. The integrated ±15 kV IEC-ESD protection improves robustness, but it does not replace proper enclosure grounding, isolation boundaries, or surge suppression for severe environments.
Do not assume that AutoShutdown behaves as a transparent zero-power state. A valid receiver signal triggers wake-up, so the host UART and connected peripheral must be designed around wake-up latency and partial-character handling. Also verify that the selected capacitor values, supply decoupling, and logic levels match the manufacturer’s reference circuit. Package similarity alone does not prove that MAX3232 or MAX3238 variants are drop-in replacements.
معلومات الامتثال
The verified manufacturer product information identifies the MAX3221 family and its technical interface features but does not state part-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this general-purpose interface IC.