MAX3232EEPE+ - 1Mbps RS-232 Transceiver | Analog Devices
MPN: MAX3232EEPE+ ✓ نشطMAX3232EEPE+ نظرة عامة
An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a serial port. The MAX3232EEPE+ belongs to the RS-232 interface IC family, where the transceiver handles electrical signaling while the connected controller manages the protocol and data format. Two driver and two receiver channels support full-duplex point-to-point links commonly used for configuration ports, industrial equipment, test systems, and legacy computer peripherals.
The device operates across a 3.0V to 5.5V supply range, allowing use with both 3.3V and 5V systems. Its maximum supported data rate is 1Mbps, while the charge-pump design eliminates the need for a separate ±12V supply. The MAX3232E family also provides ±15kV ESD protection on the serial-port connections. Receiver behavior includes a low-power mode with current down to 10nA, which helps reduce consumption when the interface is not active.
The dual charge-pump circuit generates positive and negative voltage levels required to meet RS-232 signaling thresholds. Internal driver and receiver circuits handle signal translation, while external charge-pump capacitors and supply bypass capacitors support stable operation. The MAX3232E family is designed for compatibility with the industry-standard MAX232, making it useful when an existing interface design needs a modern, low-voltage, ESD-protected implementation.
Typical uses include RS-232 links in industrial controllers, laboratory instruments, point-of-sale equipment, data acquisition systems, embedded service interfaces, and legacy PC peripherals. A 1Mbps capability supports higher-speed asynchronous communication, although cable length, baud rate, capacitance, grounding, and system timing still determine whether a particular installation can operate reliably at the maximum rate.
The principal design consideration is PCB placement. Keep the four 0.1µF charge-pump capacitors close to their designated pins, place the supply bypass capacitor near the device, and route serial traces away from noisy clocks, switching regulators, and high-current return paths. A solid ground plane and a properly referenced connector shield improve signal integrity and reduce susceptibility to common-mode noise.
This product record combines the manufacturer's electrical and packaging information with drop-in alternatives, application guidance, PCB considerations, and a parameter-by-parameter comparison. These engineering details help designers evaluate MAX3232EEPE+ for new designs and controlled replacement projects where the 16-PDIP footprint and RS-232 electrical behavior must be retained.
بدائل مباشرة لـ MAX3232EEPE+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MAX3232EEPE+ (نفس عامل الشكل والبصمة) — يختلف في Maximum Data Rate, Package Type.
MAX3232EPE+
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3232EEPE
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3232ECPE+
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3232EIPW+
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3232EEPE+ المواصفات
| Transceiver Configuration | 2/2 transceiver |
| Duplex Mode | Full duplex |
| Interface Standard | True RS-232 |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | Up to 1Mbps |
| ESD Protection | ±15kV |
| Low-Power Receiver Current | Down to 10nA |
| Number of Drivers | 2 drivers |
| Number of Receivers | 2 receivers |
| Package Type | 16-PDIP |
| Package Pitch | 0.300 inch (7.62mm) |
| نوع التركيب | Through-hole |
| Production Status | Production |
| Datasheet Revision | Rev. 13 |
| Charge-Pump Capacitors | Four 0.1µF capacitors |
دليل تكوين أطراف MAX3232EEPE+ 0.300 inch (7.62mm)
تكوين الأطراف لـ MAX3232EEPE+ (حزمة 0.300 inch (7.62mm)). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX3232EEPE+.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX3232EEPE+ مناسب لـ 6 التطبيقs: Industrial Controller Service Port, Laboratory Data Acquisition, Point-of-Sale Equipment, Embedded System Debug Interface, Legacy Computer Peripheral Connection, RS-232 Test and Measurement Fixture.
Industrial Controller Service Port
The MAX3232EEPE+ suits an RS-232 service or configuration port because it combines two drivers, two receivers, a 3.0V-to-5.5V supply range, and operation up to 1Mbps in a 16-PDIP package. The integrated charge pump generates the bipolar RS-232 levels from a single low-voltage rail, reducing the external supply complexity of legacy interface designs. Its documented ±15kV ESD protection adds useful protection where a service connector may be exposed to charged cables or maintenance activity. A controller can connect its UART signals to the transceiver inputs and outputs, while the external capacitor network and serial connector provide the remaining system interface.
موصى به
Laboratory Data Acquisition
For laboratory instruments and data-acquisition equipment, the MAX3232EEPE+ provides a compact full-duplex RS-232 link without requiring a separate ±12V supply. Two driver and two receiver channels support bidirectional communication with a host, controller, or service computer, while the 1Mbps rating provides useful margin for high-speed command and data traffic. The 3.0V-to-5.5V operating range allows the transceiver to share either 3.3V or 5V system rails. Designers should preserve a continuous ground return, place the charge-pump capacitors close to the device, and keep the connector route away from analog and switching sections to maintain measurement integrity.
موصى به
Point-of-Sale Equipment
The MAX3232EEPE+ can support bidirectional RS-232 communication between point-of-sale equipment and a cash register, printer, or customer-facing terminal. The 2/2 full-duplex arrangement allows command traffic and device responses to share the same physical interface, while the single-supply charge-pump design fits compact 3.3V or 5V systems. Its 1Mbps capability is substantially above common legacy serial baud rates, although actual command throughput depends on the connected device protocol. The ±15kV ESD rating is particularly relevant for exposed equipment connections, while board layout should retain short capacitor connections and a low-impedance ground path.
موصى به
Embedded System Debug Interface
The MAX3232EEPE+ is suitable for an embedded debug or configuration interface that must support older RS-232 hosts. Two transmit channels and two receive channels provide flexible full-duplex connectivity, and the 3.0V-to-5.5V range allows operation beside modern 3.3V processors or 5V controllers. Operating up to 1Mbps can shorten transfer time for logs and firmware data, but the host software must use a compatible baud rate and framing configuration. For reliable service-port operation, use a protected connector, route the cable ground alongside the signal conductors, and keep the transceiver away from high-current switching paths.
موصى به
Legacy Computer Peripheral Connection
The MAX3232EEPE+ can modernize the electrical interface used by legacy computer peripherals, test adapters, and service equipment while retaining a conventional RS-232 connector. Its compatibility with the industry-standard MAX232 architecture makes it useful when porting an established interface design to a 3.3V or 5V supply. The integrated dual charge pump removes the need for external bipolar rails, and the 1Mbps rating supports faster serial links than many older peripherals use. When upgrading an existing board, verify every pin, supply condition, capacitor value, receiver threshold, and shutdown connection rather than relying only on the connector shape.
موصى به
RS-232 Test and Measurement Fixture
The MAX3232EEPE+ is well suited to test fixtures that connect instrumentation, analyzers, or programmable equipment to a controller over RS-232. The 2/2 channel arrangement supports bidirectional control and data transfer, while operation up to 1Mbps allows the fixture to carry commands, status information, and measurement data efficiently. Its 3.0V-to-5.5V range simplifies integration with mixed-voltage fixtures, and the integrated charge pump reduces the number of external supply rails. Maintain consistent logic levels, use a protective connector, and provide a direct ground return between the fixture and connected equipment to minimize offset and noise.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX3232EEPE+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX3232EPE+ | MAX3232EEPE | MAX3232ECPE+ | MAX3232EIPW+ |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-PDIP | 16-PDIP - same | 16-PDIP - same | 16-PDIP - same | 16-PDIP - same |
| Transceiver Configuration | 2/2 full-duplex | 2/2 full-duplex | 2/2 full-duplex | 2/2 full-duplex | 2/2 full-duplex |
| Supply Voltage Range | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V |
| Maximum Data Rate | Up to 1Mbps | Up to 1Mbps | Up to 1Mbps | Up to 1Mbps | Up to 1Mbps |
| Charge-Pump Architecture | Dual charge pump with four 0.1µF capacitors | Dual charge pump with four 0.1µF capacitors | Dual charge pump with four 0.1µF capacitors | Dual charge pump with four 0.1µF capacitors | Dual charge pump with four 0.1µF capacitors |
أبرز الفروقات
- Documented high-level ESD protection (مقابلMAX3232EPE+)
- Full-duplex integration in a standard PDIP footprint (مقابلMAX3232EEPE)
- Single-supply RS-232 operation (مقابلMAX3232ECPE+)
ملاحظات التصميم
Place the four required 0.1µF charge-pump capacitors directly beside their associated IC pins, with short traces and an adjacent ground-plane connection. Add the prescribed supply bypass capacitor near the transceiver. Avoid routing the compact charge-pump loops beneath long RS-232 traces or other high-current paths, because loop area and return current can create noise that appears on the serial outputs.
Provide a continuous ground reference between the transceiver, connector, and connected equipment. Keep the RS-232 route away from switching-regulator inductors, high-current LED drivers, clocks, and fast digital edges. If the connector is cable-mounted, consider adding connector protection and maintaining short ground leads, because long unbalanced stubs can increase ringing even when the baud rate is modest.
Do not assume that a 16-pin RS-232 transceiver is interchangeable solely because its package matches. Verify driver and receiver assignments, charge-pump capacitor pins, supply pins, ground pins, shutdown inputs, receiver thresholds, and thermal ratings against the original schematic. Also verify that the connected UART logic levels are compatible with the 3.0V-to-5.5V supply and receiver input range.
معلومات الامتثال
The manufacturer lists the MAX3232E family as production, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not identified for this exact ordering code. AEC-Q100 is not applicable to this general-purpose RS-232 transceiver.