Analog Devices

MAX3232EEPE+ - 1Mbps RS-232 Transceiver | Analog Devices

MPN: MAX3232EEPE+ ✓ सक्रिय
3.0V to 5.5V Vdss Down to 10nA Id 16-PDIP Package
न्यूनतम ऑर्डर मात्रा: 1 |

MAX3232EEPE+ अवलोकन

The Analog Devices MAX3232EEPE+ is a 2/2 full-duplex RS-232 transceiver rated for operation from 3.0V to 5.5V, data rates up to 1Mbps, and ±15kV ESD protection, housed in a 16-pin PDIP package. It integrates two line drivers, two line receivers, and a dual charge-pump circuit that converts the low-voltage supply into the bipolar voltages required by RS-232.

An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a serial port. The MAX3232EEPE+ belongs to the RS-232 interface IC family, where the transceiver handles electrical signaling while the connected controller manages the protocol and data format. Two driver and two receiver channels support full-duplex point-to-point links commonly used for configuration ports, industrial equipment, test systems, and legacy computer peripherals.

The device operates across a 3.0V to 5.5V supply range, allowing use with both 3.3V and 5V systems. Its maximum supported data rate is 1Mbps, while the charge-pump design eliminates the need for a separate ±12V supply. The MAX3232E family also provides ±15kV ESD protection on the serial-port connections. Receiver behavior includes a low-power mode with current down to 10nA, which helps reduce consumption when the interface is not active.

The dual charge-pump circuit generates positive and negative voltage levels required to meet RS-232 signaling thresholds. Internal driver and receiver circuits handle signal translation, while external charge-pump capacitors and supply bypass capacitors support stable operation. The MAX3232E family is designed for compatibility with the industry-standard MAX232, making it useful when an existing interface design needs a modern, low-voltage, ESD-protected implementation.

Typical uses include RS-232 links in industrial controllers, laboratory instruments, point-of-sale equipment, data acquisition systems, embedded service interfaces, and legacy PC peripherals. A 1Mbps capability supports higher-speed asynchronous communication, although cable length, baud rate, capacitance, grounding, and system timing still determine whether a particular installation can operate reliably at the maximum rate.

The principal design consideration is PCB placement. Keep the four 0.1µF charge-pump capacitors close to their designated pins, place the supply bypass capacitor near the device, and route serial traces away from noisy clocks, switching regulators, and high-current return paths. A solid ground plane and a properly referenced connector shield improve signal integrity and reduce susceptibility to common-mode noise.

This product record combines the manufacturer's electrical and packaging information with drop-in alternatives, application guidance, PCB considerations, and a parameter-by-parameter comparison. These engineering details help designers evaluate MAX3232EEPE+ for new designs and controlled replacement projects where the 16-PDIP footprint and RS-232 electrical behavior must be retained.

के लिए ड्रॉप-इन विकल्प MAX3232EEPE+ — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं MAX3232EEPE+ (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Maximum Data Rate, Package Type.

Analog Devices
Maximum Data Rate: 1Mbps
Package Type: 16-pin PDIP
इसके साथ तुलना करें MAX3232EEPE+ →

MAX3232EPE+

✅ ड्रॉप-इन
📦 16-PDIP
Same 16-PDIP footprint and core 3.0V-to-5.5V, 1Mbps 2/2 interface; ESD rating is not stated in the matching listing and must be verified.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

MAX3232EEPE

✅ ड्रॉप-इन
📦 16-PDIP
Same 16-PDIP footprint and electrical function; ordering-code finish differs by the trailing plus designation, with 0% difference stated for 3.0V-to-5.5V operation and 1Mbps speed.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

MAX3232ECPE+

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Analog Devices
📦 16-PDIP
Dual RS-232 transceiver · 2 · 2 · 3.0V to 5.5V · 1Mbps · ±15kV · Down to 10nA · True RS-232

कीमत के लिए संपर्क करें

डेटाशीट देखें →

MAX3232EIPW+

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 16-PDIP
Same-family 16-PDIP 2/2 transceiver with a 0% stated difference in the 3.0V-to-5.5V supply range and 1Mbps data-rate class; temperature grade must be confirmed.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

MAX3232EEPE+ विशेषताएं

Transceiver Configuration 2/2 transceiver
Duplex Mode Full duplex
Interface Standard True RS-232
Supply Voltage Range 3.0V to 5.5V
Maximum Data Rate Up to 1Mbps
ESD Protection ±15kV
Low-Power Receiver Current Down to 10nA
Number of Drivers 2 drivers
Number of Receivers 2 receivers
Package Type 16-PDIP
Package Pitch 0.300 inch (7.62mm)
माउंटिंग प्रकार Through-hole
Production Status Production
Datasheet Revision Rev. 13
Charge-Pump Capacitors Four 0.1µF capacitors

MAX3232EEPE+ 0.300 inch (7.62mm) पिन कॉन्फ़िगरेशन गाइड

MAX3232EEPE+ (0.300 inch (7.62mm) पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

MAX3232EEPE+ के लिए 0.300 inch (7.62mm) पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: MAX3232EEPE+.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

MAX3232EEPE+ के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Controller Service Port, Laboratory Data Acquisition, Point-of-Sale Equipment, Embedded System Debug Interface, Legacy Computer Peripheral Connection, RS-232 Test and Measurement Fixture.

🏭

Industrial Controller Service Port

The MAX3232EEPE+ suits an RS-232 service or configuration port because it combines two drivers, two receivers, a 3.0V-to-5.5V supply range, and operation up to 1Mbps in a 16-PDIP package. The integrated charge pump generates the bipolar RS-232 levels from a single low-voltage rail, reducing the external supply complexity of legacy interface designs. Its documented ±15kV ESD protection adds useful protection where a service connector may be exposed to charged cables or maintenance activity. A controller can connect its UART signals to the transceiver inputs and outputs, while the external capacitor network and serial connector provide the remaining system interface.

🔧

Laboratory Data Acquisition

For laboratory instruments and data-acquisition equipment, the MAX3232EEPE+ provides a compact full-duplex RS-232 link without requiring a separate ±12V supply. Two driver and two receiver channels support bidirectional communication with a host, controller, or service computer, while the 1Mbps rating provides useful margin for high-speed command and data traffic. The 3.0V-to-5.5V operating range allows the transceiver to share either 3.3V or 5V system rails. Designers should preserve a continuous ground return, place the charge-pump capacitors close to the device, and keep the connector route away from analog and switching sections to maintain measurement integrity.

🖥️

Point-of-Sale Equipment

The MAX3232EEPE+ can support bidirectional RS-232 communication between point-of-sale equipment and a cash register, printer, or customer-facing terminal. The 2/2 full-duplex arrangement allows command traffic and device responses to share the same physical interface, while the single-supply charge-pump design fits compact 3.3V or 5V systems. Its 1Mbps capability is substantially above common legacy serial baud rates, although actual command throughput depends on the connected device protocol. The ±15kV ESD rating is particularly relevant for exposed equipment connections, while board layout should retain short capacitor connections and a low-impedance ground path.

🧩

Embedded System Debug Interface

The MAX3232EEPE+ is suitable for an embedded debug or configuration interface that must support older RS-232 hosts. Two transmit channels and two receive channels provide flexible full-duplex connectivity, and the 3.0V-to-5.5V range allows operation beside modern 3.3V processors or 5V controllers. Operating up to 1Mbps can shorten transfer time for logs and firmware data, but the host software must use a compatible baud rate and framing configuration. For reliable service-port operation, use a protected connector, route the cable ground alongside the signal conductors, and keep the transceiver away from high-current switching paths.

🖥️

Legacy Computer Peripheral Connection

The MAX3232EEPE+ can modernize the electrical interface used by legacy computer peripherals, test adapters, and service equipment while retaining a conventional RS-232 connector. Its compatibility with the industry-standard MAX232 architecture makes it useful when porting an established interface design to a 3.3V or 5V supply. The integrated dual charge pump removes the need for external bipolar rails, and the 1Mbps rating supports faster serial links than many older peripherals use. When upgrading an existing board, verify every pin, supply condition, capacitor value, receiver threshold, and shutdown connection rather than relying only on the connector shape.

📺

RS-232 Test and Measurement Fixture

The MAX3232EEPE+ is well suited to test fixtures that connect instrumentation, analyzers, or programmable equipment to a controller over RS-232. The 2/2 channel arrangement supports bidirectional control and data transfer, while operation up to 1Mbps allows the fixture to carry commands, status information, and measurement data efficiently. Its 3.0V-to-5.5V range simplifies integration with mixed-voltage fixtures, and the integrated charge pump reduces the number of external supply rails. Maintain consistent logic levels, use a protective connector, and provide a direct ground return between the fixture and connected equipment to minimize offset and noise.

अनुशंसित उत्पादों का सारांश

MAX3232EPE+ Closely related RS-232 transceiver उपयोग में: Industrial Controller Service Port, Point-of-Sale Equipment, Legacy Computer Peripheral Connection, RS-232 Test and Measurement Fixture MAX3232EEPE Closely related RS-232 transceiver उपयोग में: Industrial Controller Service Port, Point-of-Sale Equipment, Legacy Computer Peripheral Connection MAX3232ECPE+ Analog Devices उपयोग में: Laboratory Data Acquisition, Embedded System Debug Interface MAX3232EIPW+ Same-family RS-232 transceiver option उपयोग में: Laboratory Data Acquisition, Embedded System Debug Interface MAX3232EEPE+ Analog Devices उपयोग में: RS-232 Test and Measurement Fixture
What are the key specifications of MAX3232EEPE+ that engineers should know?
The MAX3232EEPE+ is a 2/2 full-duplex RS-232 transceiver with a 3.0V to 5.5V supply range, operation up to 1Mbps, and ±15kV ESD protection in a 16-PDIP package. It integrates two drivers, two receivers, and a dual charge-pump circuit, eliminating the need for an external bipolar supply. According to the Analog Devices MAX3232E product page, the device is intended for low-voltage, true RS-232 interfaces and is compatible with the industry-standard MAX232.
Where can I download the MAX3232EEPE+ datasheet PDF?
The MAX3232EEPE+ datasheet PDF is available through the linked manufacturer data sheet and the product-information page for the MAX3232E family. The linked PDF contains the electrical characteristics, charge-pump circuit, RS-232 driver and receiver specifications, ESD information, and package drawings. Use the MAX3232E datasheet revision listed on the Analog Devices product page when checking the exact MAX3232EEPE+ ordering information and test conditions.
Where can I find the MAX3232EEPE+ pinout and package information?
The MAX3232EEPE+ uses a 16-PDIP through-hole package with a 0.300-inch, or 7.62mm, pin pitch. Pin assignments, driver and receiver channels, charge-pump connections, supply pins, and capacitor connections must be assigned from the pin-description table and package drawing in the manufacturer datasheet. The device has no exposed thermal pad because it is a PDIP package rather than a surface-mount package with an exposed pad.
What is the operating voltage of MAX3232EEPE+?
The MAX3232EEPE+ operates from 3.0V to 5.5V, making it suitable for both 3.3V and 5V equipment. According to the Analog Devices MAX3232E product information, the family uses a dual charge-pump circuit to create the positive and negative voltages required by RS-232. This allows the transceiver to operate from a single low-voltage supply without the external ±12V supply previously common in RS-232 interface designs.
What is the maximum data rate of MAX3232EEPE+?
The MAX3232EEPE+ supports data rates up to 1Mbps. The Analog Devices MAX3232E product page identifies the device as a true RS-232 transceiver operating at up to 1Mbps. Actual application throughput also depends on UART timing, cable length, connector wiring, capacitance, grounding, and interference conditions, so the highest theoretical rate does not guarantee reliable communication over every cable installation.
Does MAX3232EEPE+ need an external RS-232 voltage supply?
No. The MAX3232EEPE+ generates the required positive and negative RS-232 signal levels internally with a dual charge-pump circuit. The Analog Devices MAX3232E documentation describes the use of four small charge-pump capacitors, which replace the external supply and charge-pump components required by older RS-232 designs. The system still needs the prescribed bypass and charge-pump capacitors for correct and stable operation.
What ESD protection does MAX3232EEPE+ provide?
The MAX3232EEPE+ provides ±15kV ESD protection on its RS-232 serial-port connections. According to the Analog Devices MAX3232E product-page description, the protection applies to the line-driver and line-receiver interface pins. The protection rating complements, rather than replaces, correct connector placement, short ground-return paths, cable design, and board-level shielding.
What can replace MAX3232EEPE+ without changing the PCB footprint?
The closest supported replacements are the 16-PDIP MAX3232E family variants that preserve the two-driver, two-receiver arrangement and 1Mbps capability. MAX3232EPE+ is a direct same-package option when its ESD specification is acceptable, while MAX3232EEPE and MAX3232ECPE+ provide closely related device options. Confirm supply voltage, temperature grade, ESD rating, shutdown behavior, and every pin connection in the manufacturer datasheet before production substitution.
Is MAX3232EEPE+ the same as MAX3232EPE+?
The MAX3232EEPE+ and MAX3232EPE+ belong to the same MAX3232E transceiver family and use the 16-PDIP package, but they are not identical in every specification. The MAX3232EEPE+ is identified with ±15kV ESD protection, while the MAX3232EPE+ listing is described as a 3.0V-to-5.5V, low-power RS-232 interface supporting up to 1Mbps. Confirm ESD requirements and temperature-grade details before treating either part as a substitute.
MAX3232EEPE+ vs MAX3232EPE+ — which is better for industrial control?
Choose MAX3232EEPE+ when the serial connector is exposed to electrostatic discharge risk and the system requires the documented ±15kV protection. Choose MAX3232EPE+ when its lower-power designation and specified electrical behavior satisfy the design without that enhanced ESD requirement. Both operate from 3.0V to 5.5V, support up to 1Mbps, and use the 16-PDIP footprint, so the decisive factors are protection, temperature grade, lifecycle needs, and verified channel behavior.
When should I choose MAX3232EEPE+ over MAX3232EEPE?
Choose MAX3232EEPE+ when the exact lead-free production ordering code and its documented ±15kV ESD protection are required. The MAX3232EEPE offers the same core 3.0V-to-5.5V RS-232 interface and 1Mbps capability, so it can be relevant where an approved legacy order code is preferable. Because ordering-code differences can affect qualification, package finish, and temperature grade, engineers should verify the manufacturer product table before committing either device.
Is MAX3232EEPE+ suitable for 3.3V industrial equipment?
Yes, the MAX3232EEPE+ is suitable for 3.3V equipment because its documented supply range is 3.0V to 5.5V. The 1Mbps capability can support high-speed RS-232 service links, while the integrated charge pump avoids a separate bipolar supply. Industrial suitability still depends on the verified temperature grade, ESD requirements, isolation strategy, grounding, and enclosure design rather than supply voltage alone.
What is the best cross-brand equivalent for MAX3232EEPE+?
The best cross-brand equivalent is the one that matches the 16-PDIP footprint, two-driver and two-receiver configuration, 3.0V-to-5.5V supply range, 1Mbps data rate, and required ESD level. The cross-reference results identify ICL3232CPZ and ADM232AANZ as similar devices, but their package and feature details must be checked because a similar function does not guarantee pin compatibility. Use the Request a Quote form on this page for sourcing and have the proposed replacement reviewed against the original schematic.
Where to buy MAX3232EEPE+ online?
Use the Request a Quote form on this page to request MAX3232EEPE+ availability, quantity breaks, and current lead time from XAIPART. The exact 16-PDIP ordering code should be quoted as MAX3232EEPE+ to avoid confusion with related MAX3232E package and suffix variants. Current commercial terms should be confirmed through the quote workflow rather than relying on an archived unit-price reference.
What is the price of MAX3232EEPE+?
Current price and quantity pricing for MAX3232EEPE+ are available through the Request a Quote form on this page. The structured pricing section contains a historical unit-price reference, but a quote should be used for an actual purchase because availability, volume, and commercial terms can change. Specify the required quantity, package quantity, and shipment destination when requesting the quotation.
What is the lead time for MAX3232EEPE+ and is it in stock?
Current lead time and stock status for MAX3232EEPE+ should be confirmed through the Request a Quote form on this page. The manufacturer lists the MAX3232E family as production, but a production status alone does not confirm the quantity available for a particular order. Provide your required quantity and target delivery date so XAIPART can return the most current sourcing information.

के लिए इंजीनियरिंग संदर्भ डेटा MAX3232EEPE+ — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose MAX3232EEPE+ for a new or replacement RS-232 interface that requires a 16-PDIP footprint, two drivers, two receivers, 3.0V-to-5.5V operation, data rates up to 1Mbps, and documented ±15kV ESD protection. MAX3232EPE+ is appropriate when the same core interface and footprint are needed but the enhanced ESD requirement is not applicable; verify its temperature and protection ratings first. MAX3232EEPE is closely related and electrically aligned, making it relevant for an approved legacy ordering code, although the trailing-plus distinction must be checked during procurement. MAX3232ECPE+ and MAX3232EIPW+ are same-family candidates for controlled redesigns, provided their temperature grade and pin-level behavior are confirmed. No alternative should be approved solely from its package name: compare ESD, supply, shutdown, logic thresholds, capacitance values, and every connection in the original schematic.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद MAX3232EPE+ MAX3232EEPE MAX3232ECPE+ MAX3232EIPW+
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-PDIP 16-PDIP - same 16-PDIP - same 16-PDIP - same 16-PDIP - same
Transceiver Configuration 2/2 full-duplex 2/2 full-duplex 2/2 full-duplex 2/2 full-duplex 2/2 full-duplex
Supply Voltage Range 3.0V to 5.5V 3.0V to 5.5V 3.0V to 5.5V 3.0V to 5.5V 3.0V to 5.5V
Maximum Data Rate Up to 1Mbps Up to 1Mbps Up to 1Mbps Up to 1Mbps Up to 1Mbps
Charge-Pump Architecture Dual charge pump with four 0.1µF capacitors Dual charge pump with four 0.1µF capacitors Dual charge pump with four 0.1µF capacitors Dual charge pump with four 0.1µF capacitors Dual charge pump with four 0.1µF capacitors

मुख्य विशेषताएँ

  • Documented high-level ESD protection (बनामMAX3232EPE+)
  • Full-duplex integration in a standard PDIP footprint (बनामMAX3232EEPE)
  • Single-supply RS-232 operation (बनामMAX3232ECPE+)

डिज़ाइन नोट्स

Place the four required 0.1µF charge-pump capacitors directly beside their associated IC pins, with short traces and an adjacent ground-plane connection. Add the prescribed supply bypass capacitor near the transceiver. Avoid routing the compact charge-pump loops beneath long RS-232 traces or other high-current paths, because loop area and return current can create noise that appears on the serial outputs.

Provide a continuous ground reference between the transceiver, connector, and connected equipment. Keep the RS-232 route away from switching-regulator inductors, high-current LED drivers, clocks, and fast digital edges. If the connector is cable-mounted, consider adding connector protection and maintaining short ground leads, because long unbalanced stubs can increase ringing even when the baud rate is modest.

Do not assume that a 16-pin RS-232 transceiver is interchangeable solely because its package matches. Verify driver and receiver assignments, charge-pump capacitor pins, supply pins, ground pins, shutdown inputs, receiver thresholds, and thermal ratings against the original schematic. Also verify that the connected UART logic levels are compatible with the 3.0V-to-5.5V supply and receiver input range.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The manufacturer lists the MAX3232E family as production, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not identified for this exact ordering code. AEC-Q100 is not applicable to this general-purpose RS-232 transceiver.

डेटा सत्यापन तिथि: 2026-11-14 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

MAX3232EEPE+ datasheet MAX3232EEPE+ pinout MAX3232EEPE+ datasheet pdf MAX3232EEPE+ equivalent MAX3232EEPE+ replacement MAX3232EEPE+ cross reference MAX3232EEPE+ vs MAX3232EPE+ MAX3232EEPE+ price MAX3232EEPE+ stock Analog Devices MAX3232EEPE+ MAX3232EEPE+ 16-PDIP footprint MAX3232EEPE+ RS-232 interface

संबंधित कंपोनेंट्स और शब्द

Analog Devices MAX3232EEPE+ MAX3232EPE+ MAX3232EEPE MAX3232ECPE+ MAX3232EIPW+ RS-232 transceiver RS-232 interface IC line driver line receiver dual charge pump full duplex UART 3.0V to 5.5V supply 1Mbps data rate ±15kV ESD protection 10nA low-power receiver current 16-PDIP through-hole package 0.300mm pitch industrial controller laboratory instrumentation point-of-sale equipment MAX232-compatible interface single-supply RS-232
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें