Analog Devices

MAX3243CUI+TG1Z - 3V/5V RS-232 Transceiver | Analog Devices

MPN: MAX3243CUI+TG1Z ✓ نشط
+3 V to +5.5 V Vdss 1 uA Id 28-pin TSSOP Package
الحد الأدنى للطلب: 1 |

MAX3243CUI+TG1Z نظرة عامة

Analog Devices MAX3243CUI+TG1Z is a 3/5 RS-232 transceiver integrated circuit with 1 uA supply current, a +3 V to +5.5 V operating range, and AutoShutdown functionality, supplied in a 28-pin TSSOP package. The MAX3243 family combines a driver, receiver, and charge-pump circuitry for bidirectional RS-232 interfaces while reducing the external support components normally required by conventional transceivers.

An RS-232 transceiver is an interface IC that converts between logic-level signals and RS-232 voltage levels. The driver converts low-voltage logic signals into RS-232 levels, while the receiver translates RS-232 inputs back into logic-compatible signals. As a communications interface IC within the broader semiconductor and interface-controller hierarchy, it connects equipment or microcontrollers using the EIA RS-232 standard with logic peripherals operating at lower voltage levels.

The MAX3243CUI+TG1Z provides three driver and three receiver channels, allowing up to three bidirectional RS-232 links when the transmitter and receiver directions are assigned appropriately. Its operating voltage of +3 V to +5.5 V supports both 3.3 V and 5 V system environments. The stated 1 uA supply current is the principal low-power feature, while AutoShutdown disables the internal load when no valid receiver activity is detected.

AutoShutdown makes the device suitable for battery-operated and intermittently connected equipment because the on-board power supply and drivers can shut down during idle periods. A receiver can subsequently reactivate the device when a valid signal appears. This architecture supports portable equipment, diagnostics, industrial controllers, and point-to-point serial links where reducing standby consumption is more important than maintaining continuously active drivers.

Typical uses include industrial serial adapters, service equipment, barcode and data-acquisition systems, USB-to-RS-232 interface boards, and embedded controller links. Designers should treat the MAX3243CUI+TG1Z as a single-channel-direction transceiver block rather than a full UART. The connected microcontroller or system logic must provide UART signaling, while the MAX3243 handles the physical RS-232 electrical interface.

For PCB implementation, follow the pin-description and typical-application circuits in the manufacturer datasheet for bypass-capacitor placement and charge-pump layout. Keep the connector-side traces short, provide the specified ceramic bypass capacitance close to the device, and use an appropriate protection network when exposed cables carry ESD or surge transients. Confirm the connector gender and signal assignment before fabrication because RS-232 wiring conventions are not interchangeable like UART logic.

This product page consolidates the core electrical ratings, package information, application guidance, and traceable source links for engineers evaluating the MAX3243CUI+TG1Z. It also organizes design considerations around AutoShutdown behavior, low-power operation, RS-232 signal levels, and implementation risks so the part can be selected and integrated more efficiently.

بدائل مباشرة لـ MAX3243CUI+TG1Z — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع MAX3243CUI+TG1Z (نفس عامل الشكل والبصمة) — يختلف في Product Type, Supply Voltage Range, Logic Compatibility.

Analog Devices
Product Type: RS-232 transceiver interface IC
Logic Compatibility: 3.3 V and 5 V systems
قارن مع MAX3243CUI+TG1Z →
Analog Devices
Product Type: RS-232 transceiver
Supply Voltage Range: 3.0V to 5.5V
قارن مع MAX3243CUI+TG1Z →

MAX3243CUI/T

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 28-pin TSSOP
Same +3 V to +5.5 V supply and 1 uA low-power specification; temperature-grade and order-code suffix differ by 0 V and 0 uA from the target

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX3243CUI+/T

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 28-pin TSSOP
Same +3 V to +5.5 V supply, 1 uA supply-current rating, and three-driver/three-receiver configuration; only the orderable suffix differs

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX3243EUI/T

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 28-pin TSSOP
Same +3 V to +5.5 V supply and 1 uA low-power specification; the temperature-grade suffix changes while voltage and current differences remain 0 V and 0 uA

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX3243EUI+/T

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 28-pin TSSOP
Same +3 V to +5.5 V supply and 1 uA low-power specification; temperature-grade and order-code suffixes differ, with 0 V and 0 uA core electrical differences

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX3243EEUI+T

✅ بديل مباشر
Analog Devices
📦 28-pin TSSOP
RS-232 transceiver · 3.0V to 5.5V · 250kbps · 3 drivers · 5 receivers · Full duplex · ±15kV · 1µA

تواصل لمعرفة السعر

عرض ورقة البيانات ←

MAX3243CUI+TG1Z المواصفات

Product Type 3/5 RS-232 transceiver
Supply Voltage Range +3 V to +5.5 V
تيار التغذية 1 uA
Number of Drivers 3 channels
Number of Receivers 3 channels
RS-232 Interface Full duplex
Logic Compatibility 3 V and 5 V systems
Low-Power Feature AutoShutdown
العلبة 28-pin TSSOP
نوع التركيب Surface mount
عدد الدبابيس 28 pins

دليل تكوين أطراف MAX3243CUI+TG1Z 28-pin tssop

تكوين الأطراف لـ MAX3243CUI+TG1Z (حزمة 28-pin tssop). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 28-pin tssop لـ MAX3243CUI+TG1Z

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX3243CUI+TG1Z.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

MAX3243CUI+TG1Z مناسب لـ 6 التطبيقs: Industrial RS-232 Controller Interface, Portable Diagnostic Instrument, USB-to-RS-232 Adapter, Data-Acquisition Equipment, Point-to-Point Embedded Serial Link, Automated Test and Service Interface.

🏭

Industrial RS-232 Controller Interface

The MAX3243CUI+TG1Z fits industrial controller and data-acquisition equipment that must translate controller logic into RS-232 line levels. Its +3 V to +5.5 V supply range supports both 3.3 V and 5 V logic environments, while the 1 uA supply-current specification keeps idle consumption low when AutoShutdown disables the internal supply. The three-driver and three-receiver arrangement supports several point-to-point links in one 28-pin TSSOP device. Designers should use the datasheet pin table to assign transmitter-enable signals and follow its charge-pump and bypass-capacitor layout to preserve RS-232 performance.

🧩

Portable Diagnostic Instrument

The MAX3243CUI+TG1Z is appropriate for handheld service tools and portable diagnostic equipment that connect to legacy RS-232 ports. Its 1 uA supply-current characteristic reduces standby demand, and AutoShutdown allows the internal drivers and load to remain off until valid receiver activity is detected. The device accepts a +3 V to +5.5 V supply, making it suitable for battery-managed systems built around either 3.3 V or 5 V processors. In a complete instrument, pair the interface with level-compatible UART logic, protect the exposed connector against ESD, and verify the charge-pump capacitor layout against the manufacturer application circuit.

🌐

USB-to-RS-232 Adapter

The MAX3243CUI+TG1Z can provide the physical RS-232 layer in a USB-to-serial adapter when paired with a USB-to-UART controller. Its +3 V to +5.5 V range broadens compatibility with modern USB bridge solutions, and AutoShutdown reduces consumption when the port is idle. The three transmitter and three receiver channels can serve multiple serial ports or support full-duplex arrangements where the application requires it. Because the MAX3243 is not a USB controller, the complete design still needs a USB bridge, correct driver support, connector-level protection, and the datasheet-specified bypass and charge-pump layout.

📊

Data-Acquisition Equipment

The MAX3243CUI+TG1Z suits laboratory and industrial data-acquisition equipment that communicates with RS-232 instruments or controllers. Its low 1 uA supply current and automatic shutdown behavior reduce unnecessary activity when the receiver is idle, while the three driver and three receiver channels can support multiple instrument links. Operating from +3 V to +5.5 V allows integration with modern acquisition controllers without requiring a dedicated 5 V-only interface rail. Accurate measurements depend on correct signal grounding, isolated or protected cable connections, and a clean layout around the MAX3243's charge-pump and supply components.

🔧

Point-to-Point Embedded Serial Link

The MAX3243CUI+TG1Z is well suited to point-to-point links between an embedded controller and a local service port, printer, controller, or test fixture. A 3.3 V system can use the same +3 V to +5.5 V device family, and AutoShutdown helps manage power when no valid incoming signal is present. The 28-pin TSSOP package supports compact surface-mount layouts, but connector access and signal protection can determine the final board area. Designers should assign UART receive and transmit directions clearly, use the pin-description table for enables and charge-pump nodes, and test the cable interface under real ground-offset conditions.

🖥️

Automated Test and Service Interface

The MAX3243CUI+TG1Z can terminate an RS-232 service connection in automated test equipment, programming fixtures, and configuration systems. Its three driver and three receiver channels provide useful flexibility for combining full-duplex control and status links, while the +3 V to +5.5 V range supports contemporary test controllers. The 1 uA idle specification is advantageous in shared or rack-mounted systems where unused ports should not consume substantial standby power. Production validation should confirm the temperature grade, connector gender, enable timing, cable protection, and all 28 pin assignments before releasing the fixture design.

What is the MAX3243CUI+TG1Z?
The MAX3243CUI+TG1Z is a 3/5 RS-232 transceiver from Analog Devices with three driver channels, three receiver channels, a +3 V to +5.5 V supply range, and a 28-pin TSSOP package. Its 1 uA supply current and AutoShutdown feature suit low-power serial equipment. The manufacturer datasheet identifies it as a true +3 V to +5.5 V RS-232 transceiver for logic-level systems operating at either 3 V or 5 V.
What is the operating voltage of MAX3243CUI+TG1Z?
The MAX3243CUI+TG1Z operates from +3 V to +5.5 V, allowing the same interface circuit to serve 3.3 V and 5 V logic systems. According to the MAX3243 manufacturer datasheet, the device includes on-board charge-pump circuitry for RS-232 signal generation. Its true low-voltage operation makes it suitable for embedded products, portable instruments, and modern controller boards that no longer use a 5 V-only interface.
How much supply current does MAX3243CUI+TG1Z use?
The MAX3243CUI+TG1Z has a stated supply current of 1 uA in its low-power operating condition. Analog Devices describes the MAX3243 family as using AutoShutdown to disable the on-board power supply and drivers when no valid receiver signal is present. This low idle consumption is valuable in battery-operated equipment, although the complete system power budget should also account for active-driver and external-circuit consumption.
How many RS-232 channels does MAX3243CUI+TG1Z provide?
The MAX3243CUI+TG1Z provides three RS-232 drivers and three RS-232 receivers. The family is described as a 3/5 full RS-232 transceiver in a 28-pin TSSOP package. A channel can transmit in one direction and receive in the other when the interface requires full-duplex communication. Verify the direction and enable controls in the datasheet pin table before assigning external connector signals.
Where can I download the MAX3243CUI+TG1Z datasheet PDF?
The MAX3243CUI+TG1Z datasheet PDF is available from the listed document source at https://pdf.digi-electronics.com/pdf/1471/MAX3243CUITG1Z-datasheet.pdf. Use the manufacturer document for definitive pin names, electrical characteristics, timing, capacitor values, and charge-pump layout. The MAX3243 family datasheet also provides general information for related MAX3221, MAX3223, and MAX3243 devices.
Where is the MAX3243CUI+TG1Z pinout located?
The MAX3243CUI+TG1Z pinout is located in the pin-description and package diagrams in the MAX3243 manufacturer datasheet. The device uses a 28-pin TSSOP package. Use that table to identify each driver's enable input, receiver output, charge-pump capacitor connection, supply pins, and ground pins rather than inferring connections from another RS-232 transceiver family.
Where can I buy MAX3243CUI+TG1Z and check current availability?
Use the Request a Quote form on this page to request MAX3243CUI+TG1Z availability, lead time, and commercial terms from XAIPART. The part is listed by distributors as a 3/5 full RS-232 transceiver in a 28-TSSOP package, but current inventory can change rapidly. Submit the required quantity and target date so the request can be matched to the appropriate supply channel.
What is the price of MAX3243CUI+TG1Z?
Current pricing for MAX3243CUI+TG1Z is handled through the Request a Quote form on this page. The device's commercial configuration can include temperature-grade, packing, and order-quantity considerations that should be confirmed before placing an order. Submit the exact MPN, quantity, and delivery requirements to obtain a current quotation without relying on an outdated distributor price.
What is the lead time for MAX3243CUI+TG1Z?
The current MAX3243CUI+TG1Z lead time depends on supplier inventory, order quantity, and the requested delivery date. Use the Request a Quote form on this page with the required quantity, reel or other packing preference, and target date. Do not assume a fixed lead time from general marketplace activity because serialized order codes and replenishment schedules can affect availability.
Is MAX3243CUI+TG1Z in stock?
Stock for MAX3243CUI+TG1Z should be confirmed through the Request a Quote form on this page. The exact orderable MPN includes the MAX3243CUI+ device variant, temperature-grade code, and TG1Z packing suffix, so it is important to request that complete part number. A current stock response should also confirm reel quantity and production traceability requirements.
What is the best drop-in replacement for MAX3243CUI+TG1Z?
A drop-in replacement must retain the 28-pin TSSOP footprint, three driver and three receiver functions, and the +3 V to +5.5 V operating range. Same-family MAX3243 variants can be considered when their temperature grade, enable configuration, and packing code meet the design requirements, but no unqualified cross-family substitute should be assumed compatible. The manufacturer datasheet and a circuit-level comparison should confirm pinout, timing, and charge-pump connections before substitution.
Can MAX3243CUI+TG1Z replace a MAX3237CAI+T?
MAX3243CUI+TG1Z can be evaluated as a MAX3237CAI+T replacement only after checking the complete pinout, supply limits, driver enable behavior, receiver thresholds, and package dimensions. The MAX3237CAI+T comparison identifies both parts as RS-232 transceivers, but functional similarity alone does not guarantee drop-in compatibility. Use the comparison document and both manufacturer datasheets to verify every connected pin before approving a substitution.
MAX3243CUI+TG1Z vs MAX3243EEUI+T: which is better for low-power equipment?
Choose MAX3243CUI+TG1Z when its exact temperature grade, package, and order code meet the equipment requirements; both devices belong to the MAX3243 family and use the same AutoShutdown concept. The MAX3243EEUI+T comparison is useful for identifying differences in temperature grade, mounting style, package details, and compliance. For battery-operated equipment, confirm the operating-temperature requirement and active current in addition to the shared 1 uA low-power figure.
What is the difference between MAX3243CUI+TG1Z and MAX3237CAI+T?
The principal documented difference is that MAX3243CUI+TG1Z belongs to the MAX3243 family and is specified for true +3 V to +5.5 V operation with 1 uA supply current, while MAX3237CAI+T is a different MAX3237-family device. Their RS-232 channel counts, logic thresholds, enable controls, and auxiliary pins must be compared individually. A board change should be approved only after checking the complete datasheet pin correspondence.
When should I choose MAX3243CUI+TG1Z over a MAX3243 family alternative?
Choose MAX3243CUI+TG1Z when the design needs its documented +3 V to +5.5 V operation, 1 uA low-power characteristic, three driver and three receiver channels, and 28-pin TSSOP construction. Select another same-family variant only when temperature grade, enable configuration, packing, or lifecycle needs differ. The TG1Z suffix is a specific orderable packing code, so procurement requirements must be confirmed before selecting a replacement.
Is MAX3243CUI+TG1Z suitable for a 3.3 V embedded controller?
Yes, MAX3243CUI+TG1Z is suitable for a 3.3 V embedded-controller interface because it supports a +3 V to +5.5 V supply range and true low-voltage RS-232 operation. The host UART and the transceiver logic interface must use compatible signal levels, while the MAX3243 generates and receives the RS-232 line levels. Confirm enable polarity, connector wiring, and capacitor selection using the manufacturer application circuit.
What are the key specifications of MAX3243CUI+TG1Z that engineers should know?
The key MAX3243CUI+TG1Z specifications are a +3 V to +5.5 V supply range, 1 uA supply current, three driver channels, three receiver channels, full RS-232 operation, AutoShutdown, and a 28-pin TSSOP package. These characteristics place it in the low-power RS-232 interface IC category. Data rate, temperature range, exact driver levels, and protection ratings must be taken from the manufacturer datasheet for the final design release.

بيانات مرجعية هندسية لـ MAX3243CUI+TG1Z — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose MAX3243CUI+TG1Z for a new design that requires a low-power 3/5 RS-232 interface, three driver and three receiver channels, a +3 V to +5.5 V supply, and a 28-pin TSSOP footprint. Its 1 uA supply-current specification and AutoShutdown function are especially useful in portable, diagnostic, and intermittently connected equipment. MAX3243CUI/T or MAX3243CUI+/T can be preferred when their order code better matches production requirements. MAX3243EUI/T and MAX3243EUI+/T suit designs needing a different temperature grade, while MAX3243EEUI+T is the extended-temperature same-family option referenced by the comparison data. In every case, confirm the exact temperature range, enable configuration, packing code, and pin table. MAX3237CAI+T is not automatically interchangeable because it belongs to a different family, so use a complete pin-by-pin review rather than treating it as a drop-in part.

المقارنة مع البدائل

المعامل هذا المنتج MAX3243CUI/T MAX3243CUI+/T MAX3243EUI/T MAX3243EUI+/T MAX3243EEUI+T
Package 28-pin TSSOP 28-pin TSSOP 28-pin TSSOP 28-pin TSSOP 28-pin TSSOP 28-pin TSSOP
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Product Type 3/5 RS-232 transceiver 3/5 RS-232 transceiver 3/5 RS-232 transceiver 3/5 RS-232 transceiver 3/5 RS-232 transceiver 3/5 RS-232 transceiver
Supply Voltage Range +3 V to +5.5 V +3 V to +5.5 V +3 V to +5.5 V +3 V to +5.5 V +3 V to +5.5 V +3 V to +5.5 V
Supply Current 1 uA 1 uA 1 uA 1 uA 1 uA 1 uA
Driver and Receiver Channels 3 drivers and 3 receivers 3 drivers and 3 receivers 3 drivers and 3 receivers 3 drivers and 3 receivers 3 drivers and 3 receivers 3 drivers and 3 receivers
Low-Power Control AutoShutdown AutoShutdown AutoShutdown AutoShutdown AutoShutdown AutoShutdown

أبرز الفروقات

  • Low-power operation with automatic shutdown (مقابلMAX3243EEUI+T)
  • Wide compatibility with modern logic rails (مقابلMAX3243EUI/T)
  • Three full-duplex interface channels in a compact package (مقابلMAX3243CUI+/T)

ملاحظات التصميم

Place the charge-pump capacitors and supply-bypass capacitors close to their associated MAX3243CUI+TG1Z pins, and route the charge-pump traces as shown in the manufacturer datasheet. Keep the 28-pin TSSOP footprint within the package's land-pattern and thermal recommendations. A short return path to the supply ground is important because the charge pump transfers current between supply rails while generating the RS-232 driver voltages.

Do not treat the MAX3243CUI+TG1Z as a UART or as a direct RS-232 connector. The device requires external UART logic, correct driver-enable states, and a pin-defined connector wiring arrangement. Before fabrication, compare every receiver, driver, enable, ground, and charge-pump connection with the datasheet pin table; a similarly labeled RS-232 transceiver can still differ in enable polarity and auxiliary-pin behavior.

Evaluate the power budget in both active and AutoShutdown states rather than designing around the 1 uA low-power figure alone. The MAX3243CUI+TG1Z can operate from +3 V to +5.5 V, but the selected rail, external logic, protection components, and active-driver load affect total consumption. Use the manufacturer's operating conditions to determine whether AutoShutdown activates and how much time the system remains in its lowest-power state.

Protect an externally accessible RS-232 connector with an appropriate ESD and surge network, while accounting for the connector's ground reference and cable length. Long or unbalanced cables can experience ground offsets and ringing that affect receiver behavior. Validate the assembled cable interface with the intended equipment because logic-level UART test results alone do not verify RS-232 margins at the connector.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The MAX3243EEUI+T comparison references RoHS and REACH status, but the exact compliance declarations for MAX3243CUI+TG1Z were not established. Confirm each declaration with the manufacturer before final procurement.

تم التحقق من البيانات في: 2026-11-09 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MAX3243CUI+TG1Z datasheet MAX3243CUI+TG1Z pinout MAX3243CUI+TG1Z datasheet pdf MAX3243CUI+TG1Z equivalent MAX3243CUI+TG1Z replacement MAX3243CUI+TG1Z cross reference MAX3243CUI+TG1Z footprint MAX3243CUI+TG1Z price MAX3243CUI+TG1Z stock Analog Devices MAX3243CUI+TG1Z MAX3243CUI+TG1Z RS-232 interface MAX3243CUI+TG1Z vs MAX3243EEUI+T

المكونات والمصطلحات ذات الصلة

Analog Devices Maxim Integrated MAX3243CUI+TG1Z MAX3243CUI/T MAX3243CUI+/T MAX3243EUI/T MAX3243EUI+/T MAX3243EEUI+T MAX3237CAI+T RS-232 transceiver RS-232 interface IC communications interface IC semiconductor AutoShutdown low-dropout power architecture 3.3 V logic 5 V logic charge-pump circuitry UART ESD protection 28-pin TSSOP TSSOP package family surface-mount package power management
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر