MAX3243CUI+TG1Z - 3V/5V RS-232 Transceiver | Analog Devices
MPN: MAX3243CUI+TG1Z ✓ Hoạt độngMAX3243CUI+TG1Z Tóm tắt
An RS-232 transceiver is an interface IC that converts between logic-level signals and RS-232 voltage levels. The driver converts low-voltage logic signals into RS-232 levels, while the receiver translates RS-232 inputs back into logic-compatible signals. As a communications interface IC within the broader semiconductor and interface-controller hierarchy, it connects equipment or microcontrollers using the EIA RS-232 standard with logic peripherals operating at lower voltage levels.
The MAX3243CUI+TG1Z provides three driver and three receiver channels, allowing up to three bidirectional RS-232 links when the transmitter and receiver directions are assigned appropriately. Its operating voltage of +3 V to +5.5 V supports both 3.3 V and 5 V system environments. The stated 1 uA supply current is the principal low-power feature, while AutoShutdown disables the internal load when no valid receiver activity is detected.
AutoShutdown makes the device suitable for battery-operated and intermittently connected equipment because the on-board power supply and drivers can shut down during idle periods. A receiver can subsequently reactivate the device when a valid signal appears. This architecture supports portable equipment, diagnostics, industrial controllers, and point-to-point serial links where reducing standby consumption is more important than maintaining continuously active drivers.
Typical uses include industrial serial adapters, service equipment, barcode and data-acquisition systems, USB-to-RS-232 interface boards, and embedded controller links. Designers should treat the MAX3243CUI+TG1Z as a single-channel-direction transceiver block rather than a full UART. The connected microcontroller or system logic must provide UART signaling, while the MAX3243 handles the physical RS-232 electrical interface.
For PCB implementation, follow the pin-description and typical-application circuits in the manufacturer datasheet for bypass-capacitor placement and charge-pump layout. Keep the connector-side traces short, provide the specified ceramic bypass capacitance close to the device, and use an appropriate protection network when exposed cables carry ESD or surge transients. Confirm the connector gender and signal assignment before fabrication because RS-232 wiring conventions are not interchangeable like UART logic.
This product page consolidates the core electrical ratings, package information, application guidance, and traceable source links for engineers evaluating the MAX3243CUI+TG1Z. It also organizes design considerations around AutoShutdown behavior, low-power operation, RS-232 signal levels, and implementation risks so the part can be selected and integrated more efficiently.
Bộ thay thế dễ dàng lắp đặt cho MAX3243CUI+TG1Z — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3243CUI+TG1Z (cùng hình factor và footprint) — khác nhau ở Product Type, Supply Voltage Range, Logic Compatibility.
MAX3243CUI/T
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX3243CUI+/T
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX3243EUI/T
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX3243EUI+/T
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MAX3243EEUI+T
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3243CUI+TG1Z Thông số kỹ thuật
| Product Type | 3/5 RS-232 transceiver |
| Supply Voltage Range | +3 V to +5.5 V |
| Điện áp cung cấp | 1 uA |
| Number of Drivers | 3 channels |
| Number of Receivers | 3 channels |
| RS-232 Interface | Full duplex |
| Logic Compatibility | 3 V and 5 V systems |
| Low-Power Feature | AutoShutdown |
| Hộp | 28-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 28 pins |
Hướng dẫn cấu hình chân MAX3243CUI+TG1Z 28-pin tssop
Cấu hình chân cho MAX3243CUI+TG1Z (28-pin tssop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3243CUI+TG1Z.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3243CUI+TG1Z phù hợp cho 6 Áp dụngs: Industrial RS-232 Controller Interface, Portable Diagnostic Instrument, USB-to-RS-232 Adapter, Data-Acquisition Equipment, Point-to-Point Embedded Serial Link, Automated Test and Service Interface.
Industrial RS-232 Controller Interface
The MAX3243CUI+TG1Z fits industrial controller and data-acquisition equipment that must translate controller logic into RS-232 line levels. Its +3 V to +5.5 V supply range supports both 3.3 V and 5 V logic environments, while the 1 uA supply-current specification keeps idle consumption low when AutoShutdown disables the internal supply. The three-driver and three-receiver arrangement supports several point-to-point links in one 28-pin TSSOP device. Designers should use the datasheet pin table to assign transmitter-enable signals and follow its charge-pump and bypass-capacitor layout to preserve RS-232 performance.
Được đề xuất
Portable Diagnostic Instrument
The MAX3243CUI+TG1Z is appropriate for handheld service tools and portable diagnostic equipment that connect to legacy RS-232 ports. Its 1 uA supply-current characteristic reduces standby demand, and AutoShutdown allows the internal drivers and load to remain off until valid receiver activity is detected. The device accepts a +3 V to +5.5 V supply, making it suitable for battery-managed systems built around either 3.3 V or 5 V processors. In a complete instrument, pair the interface with level-compatible UART logic, protect the exposed connector against ESD, and verify the charge-pump capacitor layout against the manufacturer application circuit.
Được đề xuất
USB-to-RS-232 Adapter
The MAX3243CUI+TG1Z can provide the physical RS-232 layer in a USB-to-serial adapter when paired with a USB-to-UART controller. Its +3 V to +5.5 V range broadens compatibility with modern USB bridge solutions, and AutoShutdown reduces consumption when the port is idle. The three transmitter and three receiver channels can serve multiple serial ports or support full-duplex arrangements where the application requires it. Because the MAX3243 is not a USB controller, the complete design still needs a USB bridge, correct driver support, connector-level protection, and the datasheet-specified bypass and charge-pump layout.
Được đề xuất
Data-Acquisition Equipment
The MAX3243CUI+TG1Z suits laboratory and industrial data-acquisition equipment that communicates with RS-232 instruments or controllers. Its low 1 uA supply current and automatic shutdown behavior reduce unnecessary activity when the receiver is idle, while the three driver and three receiver channels can support multiple instrument links. Operating from +3 V to +5.5 V allows integration with modern acquisition controllers without requiring a dedicated 5 V-only interface rail. Accurate measurements depend on correct signal grounding, isolated or protected cable connections, and a clean layout around the MAX3243's charge-pump and supply components.
Được đề xuất
Point-to-Point Embedded Serial Link
The MAX3243CUI+TG1Z is well suited to point-to-point links between an embedded controller and a local service port, printer, controller, or test fixture. A 3.3 V system can use the same +3 V to +5.5 V device family, and AutoShutdown helps manage power when no valid incoming signal is present. The 28-pin TSSOP package supports compact surface-mount layouts, but connector access and signal protection can determine the final board area. Designers should assign UART receive and transmit directions clearly, use the pin-description table for enables and charge-pump nodes, and test the cable interface under real ground-offset conditions.
Được đề xuất
Automated Test and Service Interface
The MAX3243CUI+TG1Z can terminate an RS-232 service connection in automated test equipment, programming fixtures, and configuration systems. Its three driver and three receiver channels provide useful flexibility for combining full-duplex control and status links, while the +3 V to +5.5 V range supports contemporary test controllers. The 1 uA idle specification is advantageous in shared or rack-mounted systems where unused ports should not consume substantial standby power. Production validation should confirm the temperature grade, connector gender, enable timing, cable protection, and all 28 pin assignments before releasing the fixture design.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3243CUI+TG1Z — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3243CUI/T | MAX3243CUI+/T | MAX3243EUI/T | MAX3243EUI+/T | MAX3243EEUI+T |
|---|---|---|---|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | 3/5 RS-232 transceiver | 3/5 RS-232 transceiver | 3/5 RS-232 transceiver | 3/5 RS-232 transceiver | 3/5 RS-232 transceiver | 3/5 RS-232 transceiver |
| Supply Voltage Range | +3 V to +5.5 V | +3 V to +5.5 V | +3 V to +5.5 V | +3 V to +5.5 V | +3 V to +5.5 V | +3 V to +5.5 V |
| Supply Current | 1 uA | 1 uA | 1 uA | 1 uA | 1 uA | 1 uA |
| Driver and Receiver Channels | 3 drivers and 3 receivers | 3 drivers and 3 receivers | 3 drivers and 3 receivers | 3 drivers and 3 receivers | 3 drivers and 3 receivers | 3 drivers and 3 receivers |
| Low-Power Control | AutoShutdown | AutoShutdown | AutoShutdown | AutoShutdown | AutoShutdown | AutoShutdown |
Bảo phân biệt quan trọng
- Low-power operation with automatic shutdown (vsMAX3243EEUI+T)
- Wide compatibility with modern logic rails (vsMAX3243EUI/T)
- Three full-duplex interface channels in a compact package (vsMAX3243CUI+/T)
Ghi chú thiết kế
Place the charge-pump capacitors and supply-bypass capacitors close to their associated MAX3243CUI+TG1Z pins, and route the charge-pump traces as shown in the manufacturer datasheet. Keep the 28-pin TSSOP footprint within the package's land-pattern and thermal recommendations. A short return path to the supply ground is important because the charge pump transfers current between supply rails while generating the RS-232 driver voltages.
Do not treat the MAX3243CUI+TG1Z as a UART or as a direct RS-232 connector. The device requires external UART logic, correct driver-enable states, and a pin-defined connector wiring arrangement. Before fabrication, compare every receiver, driver, enable, ground, and charge-pump connection with the datasheet pin table; a similarly labeled RS-232 transceiver can still differ in enable polarity and auxiliary-pin behavior.
Evaluate the power budget in both active and AutoShutdown states rather than designing around the 1 uA low-power figure alone. The MAX3243CUI+TG1Z can operate from +3 V to +5.5 V, but the selected rail, external logic, protection components, and active-driver load affect total consumption. Use the manufacturer's operating conditions to determine whether AutoShutdown activates and how much time the system remains in its lowest-power state.
Protect an externally accessible RS-232 connector with an appropriate ESD and surge network, while accounting for the connector's ground reference and cable length. Long or unbalanced cables can experience ground offsets and ringing that affect receiver behavior. Validate the assembled cable interface with the intended equipment because logic-level UART test results alone do not verify RS-232 margins at the connector.
Thông tin tuân thủ
The MAX3243EEUI+T comparison references RoHS and REACH status, but the exact compliance declarations for MAX3243CUI+TG1Z were not established. Confirm each declaration with the manufacturer before final procurement.