MAX3485AEASA+T - 20Mbps RS-485/RS-422 Transceiver | Analog Devices
MPN: MAX3485AEASA+T ✓ نشطMAX3485AEASA+T نظرة عامة
An RS-485/RS-422 transceiver is a physical-layer interface IC that converts between digital logic signals and balanced differential signals. It belongs to the transceiver hierarchy within interface ICs and supports bidirectional communication over cables that may run through electrically noisy industrial environments. Balanced signaling improves noise immunity by receiving the difference between two conductors rather than relying on a single-ended voltage.
The device operates from a nominal 3.3V supply, with the manufacturer listing a 3V to 3.6V operating range. Its 20Mbps data rate supports factory automation, industrial control networks, telecommunications equipment, and EMI-sensitive data links. The slew-rate-limited driver reduces high-frequency switching energy, while ±20kV ESD protection strengthens the interface against electrostatic discharge encountered during installation or connection of external cabling.
Each MAX3485AE device integrates one half-duplex driver and one receiver. A shared communication path requires controlled direction switching between transmit and receive states, allowing the same pair of conductors to carry data in both directions. The analog product family also includes related MAX3483AE, MAX3488AE, and MAX3490AE devices in the same 8-pin SO package, enabling family-level design comparison when a different bus implementation or feature set is required.
Typical uses include industrial-control networks, telecommunications links, instrumentation, building controls, and embedded systems that communicate with remote nodes over balanced cable. The combination of 3.3V operation, 20Mbps signaling, slew-rate limiting, and high ESD protection makes the device suitable for low-voltage controller boards that require robust differential communications without a high-power interface solution.
The primary design considerations are bus termination, fail-safe biasing, transceiver enable timing, and ground handling. Place the interface close to the connector, provide a continuous return path, and evaluate common-mode voltage and cable length against the circuit operating limits. Do not substitute a 5V-only transceiver unless its supply range and electrical parameters are confirmed for the complete system.
This product page consolidates the manufacturer’s electrical characteristics, package information, family comparisons, and practical interface guidance into an engineering-oriented reference. It also distinguishes direct device options from broader RS-485 alternatives and highlights where existing PCB footprints require electrical verification before substitution.
بدائل مباشرة لـ MAX3485AEASA+T — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MAX3485AEASA+T (نفس عامل الشكل والبصمة) — يختلف في Maximum Data Rate, Transceiver Configuration, Package, Supported Standards, ESD Protection.
MAX3483AEASA+T
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX3485ESA+T
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←SP3485EN-L/TR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←XR3078XID-F
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN75HVD3082E
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN65HVD485E
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
PCA82C250
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ST3485E
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX3485AEASA+T المواصفات
| Product Type | RS-485/RS-422 transceiver |
| Transceiver Configuration | 1 driver / 1 receiver |
| Communication Mode | Half duplex |
| Supported Standards | RS-485 and RS-422 |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Data Rate | 20 Mbps |
| ESD Protection | ±20 kV |
| Driver Edge Rate | Slew-rate limited |
| العلبة | 8-pin SOIC |
| نوع التركيب | Surface mount |
| Ordering Package | Tape and reel |
| Automotive Qualification | Automotive-grade MAX3485AE variant |
دليل تكوين أطراف MAX3485AEASA+T tape and reel
تكوين الأطراف لـ MAX3485AEASA+T (حزمة tape and reel). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX3485AEASA+T.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX3485AEASA+T مناسب لـ 6 التطبيقs: Industrial Control Networks, Telecommunications Equipment, EMI-Sensitive Industrial Links, Building Automation Networks, Instrumentation and Test Systems, Embedded Serial-Bus Bridges.
Industrial Control Networks
The MAX3485AEASA+T fits industrial controllers that exchange commands and status over balanced RS-485 networks. Its 20Mbps maximum data rate supports high-speed polling, while ±20kV ESD protection improves interface resilience when the board connects to field wiring. The slew-rate-limited driver also reduces unwanted high-frequency energy on the bus. Install the transceiver near the connector, use a continuous ground reference, and validate the network’s cable length, topology, termination, and common-mode limits against the application requirements.
موصى به
Telecommunications Equipment
The MAX3485AEASA+T is appropriate for telecommunications equipment that needs a compact 3.3V balanced interface for supervisory, backplane, or remote-unit links. Its 20Mbps capability provides substantial link-rate headroom, while slew-rate limiting supports cleaner operation in electromagnetic environments. Keep the differential route short and controlled, provide adequate return-path continuity, and account for transceiver enable timing. Because equipment-rack interfaces may impose stricter common-mode and isolation requirements, confirm those system-level conditions before approving the connection.
موصى به
EMI-Sensitive Industrial Links
The MAX3485AEASA+T suits EMI-sensitive systems where a differential bus must remain reliable around motors, contactors, relays, and switching power converters. Differential reception rejects a large portion of common-mode noise, and the ±20kV ESD rating improves protection for exposed communications wiring. The 3.3V operation also simplifies integration with modern controller logic. For best results, maintain a low-impedance ground relationship, avoid long stubs, use appropriate bus termination, and verify the achieved cable length with the manufacturer’s interface guidance.
موصى به
Building Automation Networks
The MAX3485AEASA+T can connect building controllers, sensors, and remote modules over a low-voltage RS-485 network. Its 3V-to-3.6V operating range suits 3.3V embedded controllers, while the 20Mbps rate limit allows the bus to serve both routine status traffic and faster configuration exchanges. The half-duplex architecture requires disciplined bus-direction control, so the firmware must avoid simultaneous transmission from multiple nodes. Confirm termination, fail-safe biasing, cable topology, and electrostatic requirements for each installation environment.
موصى به
Instrumentation and Test Systems
The MAX3485AEASA+T is useful in laboratory and industrial instrumentation that must exchange measurements and commands with remote fixtures over a balanced link. Its 20Mbps data-rate capability allows rapid command-response operation, and the 8-pin SOIC package keeps the interface compact. Slew-rate limiting can improve signal quality across practical cable lengths, although actual reach depends on topology, cable characteristics, termination, and data rate. Evaluate grounding and common-mode behavior at every external connector, especially where instruments share grounds with high-power equipment.
موصى به
Embedded Serial-Bus Bridges
The MAX3485AEASA+T can provide the physical layer for a microcontroller or programmable-logic controller bridging UART traffic onto an RS-485 or RS-422 network. Its 3.3V supply aligns with many embedded processors, while the 20Mbps maximum rate exceeds the needs of many control networks. The interface consumes one driver and one receiver, so the host must manage direction and receiver enable state correctly. Add protocol-appropriate timeout handling, fail-safe biasing, ESD-aware connector design, and controlled bus arbitration to prevent unintended bus contention.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX3485AEASA+T — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX3483AEASA+T | SP3485EN-L/TR | SN75HVD3082E | PCA82C250 | ST3485E |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Maxim Integrated | Texas Instruments | NXP Semiconductors | STMicroelectronics |
| Package | 8-pin SOIC | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package |
| Interface Standards | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 | RS-485 | RS-485 | RS-485 |
أبرز الفروقات
- 20Mbps maximum data rate with controlled edge rate (مقابلPCA82C250)
- High connector-level ESD protection (مقابلSN75HVD3082E)
- Supports both RS-485 and RS-422 in one interface (مقابلSN65HVD485E)
ملاحظات التصميم
Place the MAX3485AEASA+T close to the external connector and route the RS-485/RS-422 differential pair as a tightly coupled, continuous pair. Keep the path away from switching nodes, high-current conductors, and antenna-like structures. Use a solid ground reference beneath or adjacent to the interface where practical, and minimize stub branches because excessive stubs can reflect signals and reduce effective bus reliability at higher data rates.
Treat the half-duplex bus as a shared resource: only one node should transmit at a time. Implement transmitter-enable delays, collision avoidance, bus-timeout release, and fail-safe biasing so an idle or unpowered node does not corrupt communication. Do not assume that matching the SOIC footprint proves compatibility; verify enable polarity, receiver enable behavior, supply range, common-mode limits, and bus-impedance characteristics before approving a substitute.
The slew-rate-limited driver can reduce unwanted high-frequency energy, but EMI performance still depends on the complete installation. Use the recommended bus termination only as dictated by the network topology, retain symmetrical differential routing, and keep cable connections short or properly shielded. At equipment boundaries, verify that the transceiver’s ±20kV ESD capability is appropriate for the connector exposure and that any external protection does not distort the intended data rate or differential impedance.
Operate the device only within its 3V-to-3.6V supply range, and place local supply decoupling close to the supply and ground pins. Because the manufacturer’s product page does not state the package thermal resistance or complete maximum dissipation figure, calculate worst-case power from the selected operating mode and review ambient temperature and copper area. Avoid excessive auxiliary loading on interface pins, since their voltage and current limits can differ from the bus-driver ratings.
معلومات الامتثال
The MAX3485AEASA+T is an automotive-grade ordering variant within the MAX3485AE family. The manufacturer product information identifies the family as production, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited excerpts.