MAX353EPE+ - Quad SPST 35Ω Analog Switch | Analog Devices
MPN: MAX353EPE+ ✓ نشطMAX353EPE+ نظرة عامة
An analog switch is a semiconductor-controlled connectivity component that routes analog signals between circuit nodes. A single-pole single-throw, or SPST, switch makes or breaks one signal path rather than selecting among multiple inputs. As an integrated analog switch IC, the MAX353EPE+ provides four independent switch functions in one package, reducing component count and simplifying routing in precision signal-path systems.
The principal benefit is repeatable low on-resistance with close matching between channels. The manufacturer specifies on resistance below 35Ω, channel-to-channel matching within 2Ω, and flatness of less than 3Ω over the analog signal range. These characteristics help minimize gain errors, resistance-induced distortion, and channel-dependent offsets when signals pass through the selected switch.
The MAX353EPE+ belongs to the MAX351, MAX352, and MAX353 precision quad-SPST family. The MAX351 uses four normally closed switches, the MAX352 uses four normally open switches, and the MAX353 divides its four channels into two normally open and two normally closed configurations. This makes the MAX353 useful where both resting-connect and resting-disconnect behavior are required within one package.
Typical uses include precision measurement systems, signal-routing networks, test and measurement equipment, data-acquisition interfaces, and industrial control electronics. The mixed normally open and normally closed arrangement is especially useful for signal isolation, controlled paths to common test points, or systems that need different default connection states for different measurement channels.
PCB design should preserve the manufacturer's recommended pin assignments and provide a continuous ground return around the switching circuitry. Because the device is a through-hole PDIP package, place it close to the source and destination signal traces when practical. Review the pin-description table in the Analog Devices datasheet before assigning control inputs, supply connections, and switch terminals.
This page combines the manufacturer's device description with practical packaging guidance, application analysis, and a qualification-focused comparison against other MAX353 members. It also distinguishes true same-footprint choices from related devices that use different packages or switch configurations, helping engineers avoid substitutions that change default signal states.
بدائل مباشرة لـ MAX353EPE+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
MAX353EPE
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
MAX353CPE+
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
MAX353CPE
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
MAX353EPE+ الحدود القصوى والخصائص الكهربائية
| Number of Switch Circuits | 4 circuits |
| Switch Configuration | 2 normally open and 2 normally closed SPST switches |
| Multiplexer Configuration | 1:1 |
| Maximum On-Resistance | 35Ω |
| On-Resistance Matching Between Channels | 2Ω maximum |
| On-Resistance Variation Over Analog Signal Range | 3Ω maximum |
| عدد الدبابيس | 16 pins |
| العلبة | 16-pin PDIP |
| نوع التركيب | Through-hole |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| Product Family | MAX351, MAX352, and MAX353 precision quad-SPST analog switches |
| Production Status | Production |
دليل تكوين أطراف MAX353EPE+ rectangular
تكوين الأطراف لـ MAX353EPE+ (حزمة rectangular). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX353EPE+.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX353EPE+ مناسب لـ 6 التطبيقs: Precision Measurement Signal Routing, Data Acquisition Interface Switching, Industrial Control Signal Isolation, Test Equipment Point Selection, Analog Sensor Interface Switching, Low-Level Signal Conditioning Networks.
Precision Measurement Signal Routing
The MAX353EPE+ fits precision measurement systems that route low-level analog signals through selectable paths. Its on resistance is specified below 35Ω, while matching between channels stays within 2Ω and variation across the analog signal range stays within 3Ω. Those limits help reduce channel-dependent insertion loss and gain error. The two normally open and two normally closed switches also allow one package to provide controlled connections and isolated test paths. Place the PDIP device near the measured node when practical, and use the datasheet pin-description table to assign switch terminals and control inputs without introducing unnecessary trace resistance.
موصى به
Data Acquisition Interface Switching
The MAX353EPE+ is useful in data-acquisition interfaces that must select test, reference, or sensor paths with predictable resistance. Its maximum on resistance of less than 35Ω limits the resistive contribution when the switch is closed, and channel matching within 2Ω helps maintain consistency between acquisition channels. The four-channel package includes two normally open and two normally closed paths, supporting both active routing and default isolation. Keep analog traces compact and use a stable ground reference around the device. Confirm the switch's operating signal range against the acquired signal amplitude before finalizing the input-conditioning network.
موصى به
Industrial Control Signal Isolation
The MAX353EPE+ can serve as an industrial signal-isolation element between a controller and external measurement or drive circuits. Its specified on resistance below 35Ω provides a defined closed-state path, while the 2Ω channel-match limit supports repeatable behavior across equivalent routes. Two normally closed channels can maintain a defined connection during reset, and two normally open channels can avoid unwanted loading until commanded. Because the package is rated as industrial temperature grade, it suits equipment requiring that classification. Validate signal amplitude, supply levels, and control timing against the manufacturer datasheet before integrating it into a safety-critical control path.
موصى به
Test Equipment Point Selection
The MAX353EPE+ is appropriate for test-equipment point selection where repeatable channel resistance is needed across multiple analog paths. The less-than-35Ω on-resistance specification limits path loss, and the 2Ω matching guarantee helps prevent channel-dependent measurement offsets. Mixed normally open and normally closed contacts are useful for connecting probes, isolating unused inputs, or maintaining a defined default state. Place the device close to the test-node fanout to minimize PCB trace resistance, and keep switching traces away from high-energy or fast-switching nets. Review the pin configuration and control truth table in the datasheet before assigning the switch states.
موصى به
Analog Sensor Interface Switching
The MAX353EPE+ can switch sensor signals between measurement and processing stages when the interface must retain predictable resistance. Its on resistance below 35Ω and matching within 2Ω reduce the channel-dependent error introduced by the switch itself, while the 3Ω variation limit helps preserve flatness over the specified analog range. The two normally closed paths can retain a connection during reset, and the two normally open paths can isolate a sensor until a valid reading is requested. Use short analog traces and a quiet ground reference, and verify that the sensor output remains within the manufacturer's stated analog signal range.
موصى به
Low-Level Signal Conditioning Networks
The MAX353EPE+ fits low-level signal-conditioning networks where the on resistance of a routing switch must remain predictable. A maximum of 35Ω limits the closed-path resistance, while channel matching within 2Ω helps avoid unequal attenuation between nominally similar routes. The mixed switch configuration supports signal bypass, isolation, and alternate-path selection within one 16-pin PDIP device. Position the IC close to the conditioning components to minimize parasitic trace resistance and capacitance. Confirm the available signal range, switch timing, and control levels in the manufacturer datasheet, especially when the source impedance is high or the measured amplitude is small.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX353EPE+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX353EPE | MAX353CPE+ | MAX353CPE |
|---|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Number of Switch Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 2 normally open and 2 normally closed SPST switches | 2 normally open and 2 normally closed SPST switches | 2 normally open and 2 normally closed SPST switches | 2 normally open and 2 normally closed SPST switches |
| Multiplexer Configuration | 1:1 | 1:1 | 1:1 | 1:1 |
| Maximum On-Resistance | 35Ω maximum | 35Ω maximum | 35Ω maximum | 35Ω maximum |
| On-Resistance Matching Between Channels | 2Ω maximum | 2Ω maximum | 2Ω maximum | 2Ω maximum |
| On-Resistance Variation Over Analog Signal Range | 3Ω maximum | 3Ω maximum | 3Ω maximum | 3Ω maximum |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
أبرز الفروقات
- Mixed default connection states within one package (مقابلMAX351EPE+)
- On-resistance performance remains class-consistent (مقابلMAX353EPE)
- Supports two distinct resting states in a precision quad-SPST device (مقابلMAX352EPE+)
ملاحظات التصميم
Place the MAX353EPE+ close to the analog nodes it routes, especially when the source impedance is high. The switch contributes up to 35Ω on resistance, and PCB trace resistance becomes significant when it is comparable to that value. Keep the paths to each switch terminal short and use a continuous ground plane to minimize parasitic resistance and coupling between the four channels.
Account for the difference between the normally open and normally closed channels when defining default signal states. The mixed configuration can simplify isolation and reset behavior, but it also means that a hardware fault can connect or disconnect a path differently from the other two channels. Review the control truth table and test each state in hardware rather than assuming all four channels behave identically when deasserted.
Do not treat the MAX351, MAX352, and MAX353 as interchangeable solely because they share the quad-SPST family name. MAX351 has four normally closed switches, MAX352 has four normally open switches, and MAX353 has two of each. Substituting one family member for another can change the circuit's resting state even when the package and basic switch count appear compatible.
معلومات الامتثال
Compliance status is not stated for the exact MAX353EPE+ ordering configuration in the available product information. The plus-signed order code must be checked in the manufacturer product table before making a compliance claim.