Analog Devices

MAX353EPE+ - Quad SPST 35Ω Analog Switch | Analog Devices

N.º de pieza: MAX353EPE+ ✓ Activo
35Ω Rds(on) 16-pin PDIP Package
MOQ: 1 |

MAX353EPE+ Descripción general

The Analog Devices MAX353EPE+ is a precision, quad, single-pole single-throw analog switch in a 16-pin PDIP package. It provides four 1:1 switch channels, a maximum on-resistance specification of 35Ω, on-resistance matching within 2Ω between channels, and on-resistance variation of no more than 3Ω across the analog signal range. The circuit combines two normally open and two normally closed switches in one device.

An analog switch is a semiconductor-controlled connectivity component that routes analog signals between circuit nodes. A single-pole single-throw, or SPST, switch makes or breaks one signal path rather than selecting among multiple inputs. As an integrated analog switch IC, the MAX353EPE+ provides four independent switch functions in one package, reducing component count and simplifying routing in precision signal-path systems.

The principal benefit is repeatable low on-resistance with close matching between channels. The manufacturer specifies on resistance below 35Ω, channel-to-channel matching within 2Ω, and flatness of less than 3Ω over the analog signal range. These characteristics help minimize gain errors, resistance-induced distortion, and channel-dependent offsets when signals pass through the selected switch.

The MAX353EPE+ belongs to the MAX351, MAX352, and MAX353 precision quad-SPST family. The MAX351 uses four normally closed switches, the MAX352 uses four normally open switches, and the MAX353 divides its four channels into two normally open and two normally closed configurations. This makes the MAX353 useful where both resting-connect and resting-disconnect behavior are required within one package.

Typical uses include precision measurement systems, signal-routing networks, test and measurement equipment, data-acquisition interfaces, and industrial control electronics. The mixed normally open and normally closed arrangement is especially useful for signal isolation, controlled paths to common test points, or systems that need different default connection states for different measurement channels.

PCB design should preserve the manufacturer's recommended pin assignments and provide a continuous ground return around the switching circuitry. Because the device is a through-hole PDIP package, place it close to the source and destination signal traces when practical. Review the pin-description table in the Analog Devices datasheet before assigning control inputs, supply connections, and switch terminals.

This page combines the manufacturer's device description with practical packaging guidance, application analysis, and a qualification-focused comparison against other MAX353 members. It also distinguishes true same-footprint choices from related devices that use different packages or switch configurations, helping engineers avoid substitutions that change default signal states.

Alternativas directas para MAX353EPE+ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

MAX353EPE

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 16-pin PDIP
The 35Ω on-resistance limit and 2Ω channel-matching limit are unchanged, giving 0% difference in those key ratings; the order-code finish or qualification suffix differs and must be confirmed.

📋 Alternativa de referencia (no en el catálogo)

MAX353CPE+

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 16-pin PDIP
The core electrical ratings are unchanged at 35Ω maximum on resistance and 2Ω matching, a 0% difference; the temperature-grade suffix differs and may affect industrial-temperature requirements.

📋 Alternativa de referencia (no en el catálogo)

MAX353CPE

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 16-pin PDIP
The 35Ω on-resistance and 2Ω matching ratings remain identical, a 0% difference; temperature-grade and order-code suffix characteristics differ and require qualification review.

📋 Alternativa de referencia (no en el catálogo)

MAX353EPE+ Valores máximos y características eléctricas

Number of Switch Circuits 4 circuits
Switch Configuration 2 normally open and 2 normally closed SPST switches
Multiplexer Configuration 1:1
Maximum On-Resistance 35Ω
On-Resistance Matching Between Channels 2Ω maximum
On-Resistance Variation Over Analog Signal Range 3Ω maximum
Número de pines 16 pins
Encapsulado 16-pin PDIP
Tipo de montaje Through-hole
Package Shape Rectangular
Temperature Grade Industrial
Product Family MAX351, MAX352, and MAX353 precision quad-SPST analog switches
Production Status Production

Guía de configuración de pines de MAX353EPE+ rectangular

Configuración de pines para MAX353EPE+ (encapsulado rectangular). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado rectangular para MAX353EPE+

No hay datos detallados de patillaje disponibles para MAX353EPE+.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

MAX353EPE+ es adecuado para 6 aplicacións: Precision Measurement Signal Routing, Data Acquisition Interface Switching, Industrial Control Signal Isolation, Test Equipment Point Selection, Analog Sensor Interface Switching, Low-Level Signal Conditioning Networks.

🖥️

Precision Measurement Signal Routing

The MAX353EPE+ fits precision measurement systems that route low-level analog signals through selectable paths. Its on resistance is specified below 35Ω, while matching between channels stays within 2Ω and variation across the analog signal range stays within 3Ω. Those limits help reduce channel-dependent insertion loss and gain error. The two normally open and two normally closed switches also allow one package to provide controlled connections and isolated test paths. Place the PDIP device near the measured node when practical, and use the datasheet pin-description table to assign switch terminals and control inputs without introducing unnecessary trace resistance.

📡

Data Acquisition Interface Switching

The MAX353EPE+ is useful in data-acquisition interfaces that must select test, reference, or sensor paths with predictable resistance. Its maximum on resistance of less than 35Ω limits the resistive contribution when the switch is closed, and channel matching within 2Ω helps maintain consistency between acquisition channels. The four-channel package includes two normally open and two normally closed paths, supporting both active routing and default isolation. Keep analog traces compact and use a stable ground reference around the device. Confirm the switch's operating signal range against the acquired signal amplitude before finalizing the input-conditioning network.

🏭

Industrial Control Signal Isolation

The MAX353EPE+ can serve as an industrial signal-isolation element between a controller and external measurement or drive circuits. Its specified on resistance below 35Ω provides a defined closed-state path, while the 2Ω channel-match limit supports repeatable behavior across equivalent routes. Two normally closed channels can maintain a defined connection during reset, and two normally open channels can avoid unwanted loading until commanded. Because the package is rated as industrial temperature grade, it suits equipment requiring that classification. Validate signal amplitude, supply levels, and control timing against the manufacturer datasheet before integrating it into a safety-critical control path.

🔧

Test Equipment Point Selection

The MAX353EPE+ is appropriate for test-equipment point selection where repeatable channel resistance is needed across multiple analog paths. The less-than-35Ω on-resistance specification limits path loss, and the 2Ω matching guarantee helps prevent channel-dependent measurement offsets. Mixed normally open and normally closed contacts are useful for connecting probes, isolating unused inputs, or maintaining a defined default state. Place the device close to the test-node fanout to minimize PCB trace resistance, and keep switching traces away from high-energy or fast-switching nets. Review the pin configuration and control truth table in the datasheet before assigning the switch states.

🧩

Analog Sensor Interface Switching

The MAX353EPE+ can switch sensor signals between measurement and processing stages when the interface must retain predictable resistance. Its on resistance below 35Ω and matching within 2Ω reduce the channel-dependent error introduced by the switch itself, while the 3Ω variation limit helps preserve flatness over the specified analog range. The two normally closed paths can retain a connection during reset, and the two normally open paths can isolate a sensor until a valid reading is requested. Use short analog traces and a quiet ground reference, and verify that the sensor output remains within the manufacturer's stated analog signal range.

⚡

Low-Level Signal Conditioning Networks

The MAX353EPE+ fits low-level signal-conditioning networks where the on resistance of a routing switch must remain predictable. A maximum of 35Ω limits the closed-path resistance, while channel matching within 2Ω helps avoid unequal attenuation between nominally similar routes. The mixed switch configuration supports signal bypass, isolation, and alternate-path selection within one 16-pin PDIP device. Position the IC close to the conditioning components to minimize parasitic trace resistance and capacitance. Confirm the available signal range, switch timing, and control levels in the manufacturer datasheet, especially when the source impedance is high or the measured amplitude is small.

Resumen de productos recomendados

MAX353EPE Same-family MAX353 qualification alternative Se usa en: Precision Measurement Signal Routing, Data Acquisition Interface Switching, Industrial Control Signal Isolation, Test Equipment Point Selection, Analog Sensor Interface Switching, Low-Level Signal Conditioning Networks MAX353CPE+ Same-family temperature-grade alternative Se usa en: Precision Measurement Signal Routing, Industrial Control Signal Isolation, Test Equipment Point Selection, Low-Level Signal Conditioning Networks MAX353CPE Same-family package-compatible option Se usa en: Data Acquisition Interface Switching, Analog Sensor Interface Switching
What is the MAX353EPE+?
The MAX353EPE+ is a precision, quad, 1:1 SPST analog switch from Analog Devices with two normally open and two normally closed channels. According to the Analog Devices MAX353 datasheet, it uses a 16-pin PDIP package, has on resistance below 35Ω, and maintains channel matching within 2Ω. It is designed for precision analog routing where controlled resistance and repeatable channel behavior are important.
What are the key specifications of MAX353EPE+?
The MAX353EPE+ provides four SPST switch circuits in a 16-pin through-hole PDIP package, with two normally open and two normally closed channels. The Analog Devices MAX353 datasheet specifies maximum on resistance below 35Ω, channel-to-channel matching within 2Ω, and on-resistance variation within 3Ω over the analog signal range. The product is identified as an industrial-temperature-grade, production analog switch.
How does the MAX353EPE+ differ from MAX351 and MAX352?
The MAX353EPE+ contains two normally open and two normally closed switches, whereas the MAX351 has four normally closed channels and the MAX352 has four normally open channels. The Analog Devices MAX353 datasheet describes all three as precision quad-SPST devices with on resistance below 35Ω. Choose MAX353 when mixed default connection states are required rather than all-open or all-closed behavior.
Where can I download the MAX353EPE+ datasheet PDF?
The official MAX353 product page on Analog Devices provides the manufacturer datasheet and supporting documentation. According to Analog Devices, the MAX353 is a production precision quad-SPST analog switch in 16-pin PDIP. Use the datasheet's pin-description table, electrical-characteristics table, and typical-application circuits when assigning terminals, control inputs, supply pins, and layout.
Where is the MAX353EPE+ pinout located?
The MAX353EPE+ pinout is located in the pin-configuration and pin-description sections of the Analog Devices MAX353 datasheet. The device is a 16-pin PDIP package with through-hole mounting. Use that diagram to identify the two normally open switch pairs, two normally closed switch pairs, control inputs, supply terminals, and ground before laying out the PCB.
Is the MAX353EPE+ suitable for precision measurement systems?
The MAX353EPE+ is suitable for precision measurement systems that need low and repeatable on resistance. According to the Analog Devices MAX353 datasheet, on resistance remains below 35Ω, matching between channels is within 2Ω, and variation over the analog signal range is within 3Ω. These specifications help limit channel-dependent gain errors in low-level signal-routing paths.
When should I choose MAX353EPE+ over MAX351EPE+ or MAX352EPE+?
Choose the MAX353EPE+ when one package must provide both normally open and normally closed paths; it contains two channels of each type. Choose MAX351EPE+ when every channel should default to closed, or MAX352EPE+ when every channel should default to open. The Analog Devices family uses a common precision quad-SPST architecture, making default switch state the principal selection criterion.
What can replace the MAX353EPE+?
The closest same-footprint replacements are qualified MAX353-family variants that retain the four-channel mixed 2-NO/2-NC configuration and 16-pin PDIP footprint. MAX353EPE and MAX353CPE+ can be considered only after checking their temperature-grade and order-code requirements against the original design. The Analog Devices MAX353 datasheet remains the controlling document for pin and electrical compatibility.
Is there a known cross-brand drop-in replacement for MAX353EPE+?
No cross-brand drop-in replacement with a verified 16-pin PDIP footprint, pin-to-pin assignment, and mixed 2-NO/2-NC configuration was identified. Related cross-reference pages list devices in different packages or with different switch behavior, so they cannot automatically replace the MAX353EPE+ without PCB changes or signal-state changes. Validate any proposed substitute against the Analog Devices datasheet before use.
Is MAX353EPE+ the same as MAX353EPE?
The MAX353EPE+ and MAX353EPE are closely related MAX353 order codes with the same core device description, but the trailing plus sign denotes a distinct ordering configuration that must be confirmed in the manufacturer product table. Both identify a precision quad-SPST device with two normally open and two normally closed channels. Check the exact order code, package, temperature grade, and qualification requirements before substitution.
Where can I buy MAX353EPE+ online?
Use the Request a Quote form on this page to request MAX353EPE+ availability, order quantities, and current commercial terms. The listed part is a production 16-pin PDIP analog switch from Analog Devices. A complete purchase decision should also confirm lead time, authorized-channel provenance, and whether the quantity matches the supplier's available packaging configuration.
What is the lead time for MAX353EPE+?
The current lead time for MAX353EPE+ should be requested through the Request a Quote form on this page. The Analog Devices product page identifies the MAX353 family as production, but manufacturing lead time and lot allocation can vary with order volume and supply conditions. State your required quantity, target date, and acceptable packaging configuration when requesting the quotation.
Is MAX353EPE+ in stock?
Current MAX353EPE+ stock status should be confirmed through the Request a Quote form on this page. Analog Devices identifies the MAX353 as a production device, but production status alone does not guarantee immediate inventory at every quantity. Provide your required quantity and shipment location so the current allocation and estimated lead time can be reviewed.
How does MAX353EPE+ affect signal accuracy?
The MAX353EPE+ affects signal accuracy through its on resistance and the variation of that resistance across channels and signal levels. The Analog Devices MAX353 datasheet specifies less than 35Ω on resistance, matching within 2Ω, and variation within 3Ω over the analog signal range. These limits determine the switch-induced insertion loss and channel-to-channel gain deviation.
Does MAX353EPE+ meet RoHS and automotive qualification requirements?
The MAX353EPE+ should not be treated as automotive-qualified unless the exact order code carries that qualification. RoHS, REACH, AEC-Q100, lead-free, and halogen-free status must be confirmed for the exact MAX353EPE+ ordering configuration in the manufacturer product documentation. The family-level description identifies industrial temperature grade and production status, but it does not by itself establish automotive qualification.

Datos de referencia de ingeniería para MAX353EPE+ — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose MAX353EPE+ when a 16-pin PDIP precision analog switch must combine two normally open and two normally closed channels. Its less-than-35Ω on resistance, 2Ω channel matching, and 3Ω signal-range variation make it appropriate where predictable path resistance matters. MAX353EPE is the closest same-core order-code alternative when the plus-sign configuration is not required. MAX353CPE+ and MAX353CPE preserve the same package and core switching architecture but require a careful temperature-grade review. Do not choose MAX351EPE+ or MAX352EPE+ as automatic drop-ins when default switch states matter: MAX351 uses four normally closed channels, while MAX352 uses four normally open channels. For any alternate part, verify the 16-pin PDIP footprint, pin assignment, control logic, analog signal range, electrical limits, and qualification status against the manufacturer datasheet.

Comparación con alternativas

Parámetro Este producto MAX353EPE MAX353CPE+ MAX353CPE
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Number of Switch Circuits 4 circuits 4 circuits 4 circuits 4 circuits
Switch Configuration 2 normally open and 2 normally closed SPST switches 2 normally open and 2 normally closed SPST switches 2 normally open and 2 normally closed SPST switches 2 normally open and 2 normally closed SPST switches
Multiplexer Configuration 1:1 1:1 1:1 1:1
Maximum On-Resistance 35Ω maximum 35Ω maximum 35Ω maximum 35Ω maximum
On-Resistance Matching Between Channels 2Ω maximum 2Ω maximum 2Ω maximum 2Ω maximum
On-Resistance Variation Over Analog Signal Range 3Ω maximum 3Ω maximum 3Ω maximum 3Ω maximum
Mounting Type Through-hole Through-hole Through-hole Through-hole

Diferenciadores clave

  • Mixed default connection states within one package (frente a MAX351EPE+)
  • On-resistance performance remains class-consistent (frente a MAX353EPE)
  • Supports two distinct resting states in a precision quad-SPST device (frente a MAX352EPE+)

Notas de diseño

Place the MAX353EPE+ close to the analog nodes it routes, especially when the source impedance is high. The switch contributes up to 35Ω on resistance, and PCB trace resistance becomes significant when it is comparable to that value. Keep the paths to each switch terminal short and use a continuous ground plane to minimize parasitic resistance and coupling between the four channels.

Account for the difference between the normally open and normally closed channels when defining default signal states. The mixed configuration can simplify isolation and reset behavior, but it also means that a hardware fault can connect or disconnect a path differently from the other two channels. Review the control truth table and test each state in hardware rather than assuming all four channels behave identically when deasserted.

Do not treat the MAX351, MAX352, and MAX353 as interchangeable solely because they share the quad-SPST family name. MAX351 has four normally closed switches, MAX352 has four normally open switches, and MAX353 has two of each. Substituting one family member for another can change the circuit's resting state even when the package and basic switch count appear compatible.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

Compliance status is not stated for the exact MAX353EPE+ ordering configuration in the available product information. The plus-signed order code must be checked in the manufacturer product table before making a compliance claim.

Datos verificados el: 2026-11-19 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

MAX353EPE+ datasheet MAX353EPE+ pinout MAX353EPE+ datasheet pdf MAX353EPE+ replacement MAX353EPE+ equivalent MAX353EPE+ cross reference MAX353EPE+ footprint MAX353EPE+ price MAX353EPE+ stock Analog Devices MAX353EPE+ MAX353EPE+ 35 ohm analog switch MAX353EPE+ 16 pin PDIP

Componentes & términos relacionados

Analog Devices MAX353EPE+ MAX353EPE MAX353CPE+ MAX353CPE MAX351 MAX352 MAX353 Precision quad-SPST analog switch SPST switch Normally open switch Normally closed switch Analog switch IC Multiplexer Interface IC Semiconductor On resistance Channel matching Analog signal range 16-pin PDIP DIP package Through-hole mounting Signal routing Data acquisition Precision measurement
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ