Analog Devices

MAX362CSE+ - 4-Channel SPST Analog Switch | Analog Devices

MPN: MAX362CSE+ ✓ نشط
85 ohm Rds(on) 16-pin SOIC Package
الحد الأدنى للطلب: 1 |

MAX362CSE+ نظرة عامة

The Analog Devices MAX362CSE+ is a precision quad, single-pole single-throw analog switch with four normally open switches, packaged in a 16-pin SOIC. The device provides a 1:1 signal configuration and an on resistance of 85 ohms, making it suitable for routing precision analog signals in test, measurement, instrumentation, and communication equipment.

An analog switch is a semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw, or SPST, switch contains one signal path that is either connected or disconnected. The MAX362 uses four normally open channels, so each channel is off during its inactive state and connects the selected signal when the corresponding control input is asserted. This topology is useful when a system must route one source to one destination without connecting the active path permanently.

The MAX362 family is designed for precision signal handling. According to the Analog Devices MAX362 product page, the on resistance is less than 85 ohms, channel-to-channel matching is guaranteed within 3 ohms, and resistance variation across the analog signal range is limited to a maximum change of 9 ohms. These characteristics support predictable signal attenuation when the same switch is used with different channels or operating signal levels.

The MAX362CSE+ provides four independently controlled switch channels in a 16-SOIC package. The MAX362 product family is also available in complementary normally closed form as the MAX361, allowing complementary routing behavior to be considered when designing control logic. The MAX362CSE+ ordering suffix denotes the leaded SOIC package configuration identified in the product listing.

Typical applications include precision signal routing, bench-test equipment, data-acquisition systems, communication-channel selection, and analog measurement paths. Because the switch resistance and matching characteristics are central to its performance, system-level calculations should include the effective source and load impedances, expected signal amplitude, settling behavior, and the contribution of switch on resistance.

When laying out a board around the MAX362CSE+, keep analog input and output traces short and connect the device ground pins to a low-impedance ground plane. Place nearby bypassing capacitors at the supply entry point and keep digital control traces away from sensitive analog paths. Review the manufacturer datasheet for the exact pin assignments, absolute maximum ratings, recommended operating conditions, and electrical characteristics before releasing the layout.

This product page combines the manufacturer family description, package identification, sourcing information, practical layout guidance, and a structured comparison framework to support component selection and PCB design. It also distinguishes verified product facts from parameters that require confirmation in the MAX362 datasheet.

بدائل مباشرة لـ MAX362CSE+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع MAX362CSE+ (نفس عامل الشكل والبصمة) — يختلف في Mounting Type, Package.

Maxim Integrated
Mounting Type: Surface Mount (SMD/SMT)
Package: 16-SOIC narrow (0.154 inch / 3.90 mm width)
قارن مع MAX362CSE+ →

MAX338ESE+

✅ بديل مباشر
Maxim Integrated
📦 16-pin SOIC
8-Channel / Dual 4-Channel CMOS Analog Multiplexer (Mux or Demux) · 1 · 8:1 · 400 ohm · +4.5V to +30V · +/-4.5V to +/-20V · Bidirectional analog channel · Yes, protected channels

تواصل لمعرفة السعر

عرض ورقة البيانات ←

MAX358CPE+

✅ بديل مباشر
📦 16-pin SOIC
4 vs 4 circuits and 16 vs 16 pins, a difference of 0 in both matching dimensions; the target has a stated 85-ohm on-resistance

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX362CSE+ الحدود القصوى والخصائص الكهربائية

Number of Switches 4 circuits
Switch Configuration 1:1
Switch Type Single-pole single-throw (SPST)
Initial State Normally open (NO)
On Resistance 85 ohm
Maximum On Resistance Less than 85 ohm
On-Resistance Matching Between Channels Within 3 ohm
On-Resistance Variation Over Analog Signal Range 9 ohm maximum
العلبة 16-pin SOIC
عدد الدبابيس 16 pins
نوع التركيب Surface mount
Product Lifecycle Production

دليل تكوين أطراف MAX362CSE+ 16-pin soic

تكوين الأطراف لـ MAX362CSE+ (حزمة 16-pin soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 16-pin soic لـ MAX362CSE+

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX362CSE+.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

MAX362CSE+ مناسب لـ 6 التطبيقs: Precision Analog Signal Routing, Test and Measurement Equipment, Data Acquisition Systems, Communication Channel Selection, Instrumentation Signal Isolation, Industrial Control Signal Selection.

🔧

Precision Analog Signal Routing

The MAX362CSE+ fits precision analog routing because its four normally open SPST channels provide a 1:1 signal path while its 85-ohm on resistance remains closely matched across channels. The manufacturer specifies matching within 3 ohms and resistance variation of no more than 9 ohms over the analog signal range. Place the switch where the resulting attenuation is acceptable relative to the source and load impedances. If signal attenuation is critical, include the switch resistance in the complete source impedance because it loads the driving circuit and can influence gain accuracy.

⚡

Test and Measurement Equipment

The MAX362CSE+ is suitable for test and measurement paths that require four independently controlled analog routes in a compact 16-pin SOIC package. Its 1:1 configuration permits one source to be connected to one destination without permanently joining the route. The guaranteed on-resistance matching within 3 ohms is valuable when different channels must present similar loading. Confirm the signal amplitude, frequency, leakage, and switching-time requirements in the datasheet, and place grounding and bypass connections close to the device to avoid adding board-level noise to the measurement result.

📊

Data Acquisition Systems

The MAX362CSE+ can implement source selection or channel isolation in a data-acquisition front end because each of its four channels is a normally open SPST switch with a 1:1 path. The 85-ohm on resistance should be compared with the selected sensor output impedance and the acquisition input impedance to determine the allowable loading. Tight channel matching helps maintain consistency when the system switches among similar sources. Keep sensitive sensor traces short, maintain a continuous ground reference, and review control-signal timing so switch transitions do not overlap the acquisition sampling interval.

🌐

Communication Channel Selection

The MAX362CSE+ fits communication systems that need to route one analog signal path among several possible destinations. Its four normally open channels help prevent unintended connections between routes, while the 1:1 configuration avoids mixing signals directly at the switch pins. For high-frequency or low-amplitude links, verify the device's published bandwidth, capacitance, insertion loss, and switching-time limits in the MAX362 datasheet. Route the selected path as a controlled transmission line when required and keep the digital control nets away from the analog route to minimize coupling.

🖥️

Instrumentation Signal Isolation

The MAX362CSE+ can isolate instrumentation paths when the default state must leave the signal disconnected. The 3-ohm channel-matching guarantee and maximum 9-ohm variation across the analog range help engineers select a part that maintains repeatable channel behavior. Evaluate the switch's total on resistance against the minimum source impedance, since the MAX362CSE+ also contributes to noise gain when the source is resistive. Use a low-impedance analog ground plane, short return paths, and local supply bypassing, and confirm that input and output voltages remain within the absolute maximum limits.

🏭

Industrial Control Signal Selection

The MAX362CSE+ can select control or feedback signals in industrial systems where four independent normally open routes are useful. Its 16-pin SOIC package provides a compact implementation for analog command multiplexing, and the matched on resistance supports repeatable behavior across channels. The design must account for the 85-ohm path resistance, leakage, control thresholds, and the operating temperature range before deployment. Provide a stable supply and reference ground, keep switching nodes away from noisy power stages, and validate timing at the highest supported control rate to prevent simultaneous unwanted connections.

What is the MAX362CSE+?
The MAX362CSE+ is a precision quad SPST analog switch with four normally open channels, an 85-ohm on resistance, and a 16-pin SOIC package. According to the Analog Devices MAX362 product page, the MAX362 family is intended for precision analog signal routing and provides on-resistance matching within 3 ohms between channels.
How many switches are in the MAX362CSE+?
The MAX362CSE+ contains four independent single-pole single-throw switches. Each channel has a 1:1 signal configuration and is normally open, meaning the signal path is disconnected until the associated control input activates the channel. The four-channel count allows one device to implement several routed analog paths.
What is the on resistance of the MAX362CSE+?
The MAX362CSE+ has an on resistance of 85 ohms, while the Analog Devices product page describes the MAX362 family as having less than 85 ohms. It also guarantees channel-to-channel matching within 3 ohms and limits on-resistance variation to 9 ohms maximum over the analog signal range.
Where can I download the MAX362CSE+ datasheet?
The official MAX362 datasheet and product information are available on the Analog Devices MAX362 product page. The page provides the production status, product selection table, family description, and documentation resources. Use the manufacturer documentation for the complete pin assignment, electrical limits, and operating-condition tables before designing the circuit.
Where can I find the MAX362CSE+ pinout?
The MAX362CSE+ pinout is shown in the MAX362 manufacturer documentation for the 16-pin SOIC configuration. Use the pin-description table in that document to assign common, normally-open control inputs, and analog source and destination pins exactly as specified for your device revision.
Is the MAX362 normally open or normally closed?
The MAX362 is normally open. According to the Analog Devices MAX362 product page, each of its four SPST channels is disconnected in the inactive state and connects the selected signal when controlled. The complementary MAX361 family provides four normally closed channels for applications requiring the opposite default state.
What can replace the MAX362CSE+?
A valid drop-in replacement must use the same 16-pin SOIC footprint, provide four normally open SPST channels, and preserve the essential resistance, leakage, supply-voltage, control-logic, and switching-time limits. No confirmed pin-compatible replacement was identified in the available cross-reference results, so verify any candidate against the manufacturer datasheet before substitution.
What is the best Analog Devices equivalent for the MAX362CSE+?
The closest confirmed Analog Devices family member is MAX362 itself, which is identified as a precision quad normally open SPST switch with less than 85-ohm on resistance. The MAX361 is electrically complementary because it is normally closed, so it should not be treated as a direct functional replacement without a deliberate logic change.
Is MAX361 the same as MAX362?
No. The MAX361 has four normally closed switches, while the MAX362 has four normally open switches. Although both belong to the precision quad SPST family, their default signal-path states differ, so the MAX361 is not an interchangeable substitute for the MAX362 without reviewing the control logic and application behavior.
When should I choose the MAX362CSE+ over the MAX361?
Choose the MAX362CSE+ when the required default state is an open signal path, such as preventing unintended connection of a sensitive analog source. Choose the MAX361 family when an open path is normally undesirable and the default state should instead connect the selected route. The control polarity and system behavior must match the selected device.
Where can I buy the MAX362CSE+?
Use the Request a Quote form on this page to request current pricing, stock, lead time, and order details for MAX362CSE+. The listing is shown in a 16-SOIC package, and the manufacturer marks the MAX362 family as production. Commercial terms can change, so the quote form is the appropriate route for an actionable order.
What is the price of the MAX362CSE+?
Current commercial pricing for the MAX362CSE+ is available through the Request a Quote form on this page. The product is identified as a 4-circuit, 1:1, 85-ohm SPST analog switch in a 16-SOIC package. Submit the required quantity, target packaging, and delivery location to receive an actionable quotation.
What is the lead time and stock status for MAX362CSE+?
Request current lead time, stock status, and minimum order quantity through the Request a Quote form on this page. The Analog Devices product page identifies the MAX362 family as production, but current availability can vary by package suffix, order quantity, and market conditions. A quotation request provides the most appropriate operational answer.
MAX362CSE+ versus MAX362CSE+T: which package option fits my design?
Both orderable listings identify the MAX362 family in the 16-SOIC configuration, but the packaging interpretation must be confirmed from the ordering information before assembly. MAX362CSE+ is the target leaded SOIC listing, while MAX362CSE+T is listed separately. Confirm tape orientation, reel format, and solder assembly requirements with the manufacturer datasheet.
What key specifications of MAX362CSE+ should engineers check?
Engineers should check the 85-ohm on resistance, less-than-85-ohm family limit, 3-ohm channel matching, 9-ohm maximum resistance variation, four normally open SPST channels, and 16-pin SOIC package. Also verify supply voltage, leakage, control thresholds, switching time, absolute maximum ratings, and temperature limits in the manufacturer datasheet.

بيانات مرجعية هندسية لـ MAX362CSE+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the MAX362CSE+ when the design requires four precision, normally open SPST analog channels in a 16-pin SOIC package. Its 85-ohm on resistance, channel matching within 3 ohms, and resistance variation of no more than 9 ohms make it appropriate for repeatable one-to-one signal routing rather than high-current switching. The normally open state is especially useful when disconnected is the safe default during reset or fault conditions. Do not select the complementary MAX361 unless normally closed behavior is specifically required, because the two families differ in their default signal-path state. No confirmed drop-in alternative was established from the available cross-reference results, so any proposed substitute must be checked for identical pinout, control logic, voltage limits, leakage, switching speed, and resistance performance before it is approved for production.

ملاحظات التصميم

Do not treat the MAX361 and MAX362 as interchangeable without reviewing the default switch state. The MAX362 has four normally open channels, whereas the MAX361 has four normally closed channels. Although the devices share the precision quad SPST family positioning, the different default connection states can reverse the behavior of reset, fault, or power-up conditions.

Use the MAX362 pin-description table in the manufacturer datasheet to assign every analog and control pin in the 16-pin SOIC footprint. Keep the analog route compact, connect all device grounds to a continuous low-impedance plane, and separate control traces from sensitive signal paths. Avoid routing high-current or high-voltage switching traces beneath the analog pins.

Estimated attenuation depends on the complete source impedance and the switch's 85-ohm on resistance. Using a 50-ohm source, the switch alone forms 135 ohms before the load is included; the resulting divider must be checked against the required signal amplitude. Confirm capacitance, bandwidth, and switching time in the datasheet when routing fast or high-amplitude signals.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The available product information does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this precision analog switch is not identified as an automotive-qualified device.

تم التحقق من البيانات في: 2026-11-09 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MAX362CSE+ datasheet MAX362CSE+ pinout MAX362CSE+ datasheet pdf MAX362CSE+ equivalent MAX362CSE+ replacement MAX362CSE+ cross reference MAX362CSE+ footprint MAX362CSE+ price MAX362CSE+ stock Analog Devices MAX362CSE+ MAX362 16-SOIC pinout MAX362 application circuit

المكونات والمصطلحات ذات الصلة

Analog Devices MAX362CSE+ MAX362 MAX361 precision analog switch quad SPST switch single-pole single-throw normally open switch normally closed switch on resistance channel resistance matching off leakage analog signal routing test and measurement data acquisition communication channel selection industrial control 16-pin SOIC SOIC family surface-mount package semiconductor interface IC 1:1 switching configuration
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر