MAX362CSE+ - 4-Channel SPST Analog Switch | Analog Devices
Référence : MAX362CSE+ ✓ ActifMAX362CSE+ Présentation
An analog switch is a semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw, or SPST, switch contains one signal path that is either connected or disconnected. The MAX362 uses four normally open channels, so each channel is off during its inactive state and connects the selected signal when the corresponding control input is asserted. This topology is useful when a system must route one source to one destination without connecting the active path permanently.
The MAX362 family is designed for precision signal handling. According to the Analog Devices MAX362 product page, the on resistance is less than 85 ohms, channel-to-channel matching is guaranteed within 3 ohms, and resistance variation across the analog signal range is limited to a maximum change of 9 ohms. These characteristics support predictable signal attenuation when the same switch is used with different channels or operating signal levels.
The MAX362CSE+ provides four independently controlled switch channels in a 16-SOIC package. The MAX362 product family is also available in complementary normally closed form as the MAX361, allowing complementary routing behavior to be considered when designing control logic. The MAX362CSE+ ordering suffix denotes the leaded SOIC package configuration identified in the product listing.
Typical applications include precision signal routing, bench-test equipment, data-acquisition systems, communication-channel selection, and analog measurement paths. Because the switch resistance and matching characteristics are central to its performance, system-level calculations should include the effective source and load impedances, expected signal amplitude, settling behavior, and the contribution of switch on resistance.
When laying out a board around the MAX362CSE+, keep analog input and output traces short and connect the device ground pins to a low-impedance ground plane. Place nearby bypassing capacitors at the supply entry point and keep digital control traces away from sensitive analog paths. Review the manufacturer datasheet for the exact pin assignments, absolute maximum ratings, recommended operating conditions, and electrical characteristics before releasing the layout.
This product page combines the manufacturer family description, package identification, sourcing information, practical layout guidance, and a structured comparison framework to support component selection and PCB design. It also distinguishes verified product facts from parameters that require confirmation in the MAX362 datasheet.
Alternatives de remplacement direct pour MAX362CSE+ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec MAX362CSE+ (même facteur de forme et même empreinte) — différant par Mounting Type, Package.
MAX338ESE+
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →MAX358CPE+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX362CSE+ Valeurs maximales et caractéristiques électriques
| Number of Switches | 4 circuits |
| Switch Configuration | 1:1 |
| Switch Type | Single-pole single-throw (SPST) |
| Initial State | Normally open (NO) |
| On Resistance | 85 ohm |
| Maximum On Resistance | Less than 85 ohm |
| On-Resistance Matching Between Channels | Within 3 ohm |
| On-Resistance Variation Over Analog Signal Range | 9 ohm maximum |
| Boîtier | 16-pin SOIC |
| Nombre de broches | 16 pins |
| Type de montage | Surface mount |
| Product Lifecycle | Production |
Guide de configuration des broches du MAX362CSE+ 16-pin soic
Configuration des broches du MAX362CSE+ (boîtier 16-pin soic). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour MAX362CSE+.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
MAX362CSE+ convient pour 6 applications: Precision Analog Signal Routing, Test and Measurement Equipment, Data Acquisition Systems, Communication Channel Selection, Instrumentation Signal Isolation, Industrial Control Signal Selection.
Precision Analog Signal Routing
The MAX362CSE+ fits precision analog routing because its four normally open SPST channels provide a 1:1 signal path while its 85-ohm on resistance remains closely matched across channels. The manufacturer specifies matching within 3 ohms and resistance variation of no more than 9 ohms over the analog signal range. Place the switch where the resulting attenuation is acceptable relative to the source and load impedances. If signal attenuation is critical, include the switch resistance in the complete source impedance because it loads the driving circuit and can influence gain accuracy.
Recommandé
Test and Measurement Equipment
The MAX362CSE+ is suitable for test and measurement paths that require four independently controlled analog routes in a compact 16-pin SOIC package. Its 1:1 configuration permits one source to be connected to one destination without permanently joining the route. The guaranteed on-resistance matching within 3 ohms is valuable when different channels must present similar loading. Confirm the signal amplitude, frequency, leakage, and switching-time requirements in the datasheet, and place grounding and bypass connections close to the device to avoid adding board-level noise to the measurement result.
Recommandé
Data Acquisition Systems
The MAX362CSE+ can implement source selection or channel isolation in a data-acquisition front end because each of its four channels is a normally open SPST switch with a 1:1 path. The 85-ohm on resistance should be compared with the selected sensor output impedance and the acquisition input impedance to determine the allowable loading. Tight channel matching helps maintain consistency when the system switches among similar sources. Keep sensitive sensor traces short, maintain a continuous ground reference, and review control-signal timing so switch transitions do not overlap the acquisition sampling interval.
Recommandé
Communication Channel Selection
The MAX362CSE+ fits communication systems that need to route one analog signal path among several possible destinations. Its four normally open channels help prevent unintended connections between routes, while the 1:1 configuration avoids mixing signals directly at the switch pins. For high-frequency or low-amplitude links, verify the device's published bandwidth, capacitance, insertion loss, and switching-time limits in the MAX362 datasheet. Route the selected path as a controlled transmission line when required and keep the digital control nets away from the analog route to minimize coupling.
Recommandé
Instrumentation Signal Isolation
The MAX362CSE+ can isolate instrumentation paths when the default state must leave the signal disconnected. The 3-ohm channel-matching guarantee and maximum 9-ohm variation across the analog range help engineers select a part that maintains repeatable channel behavior. Evaluate the switch's total on resistance against the minimum source impedance, since the MAX362CSE+ also contributes to noise gain when the source is resistive. Use a low-impedance analog ground plane, short return paths, and local supply bypassing, and confirm that input and output voltages remain within the absolute maximum limits.
Recommandé
Industrial Control Signal Selection
The MAX362CSE+ can select control or feedback signals in industrial systems where four independent normally open routes are useful. Its 16-pin SOIC package provides a compact implementation for analog command multiplexing, and the matched on resistance supports repeatable behavior across channels. The design must account for the 85-ohm path resistance, leakage, control thresholds, and the operating temperature range before deployment. Provide a stable supply and reference ground, keep switching nodes away from noisy power stages, and validate timing at the highest supported control rate to prevent simultaneous unwanted connections.
Recommandé
Données de référence d'ingénierie pour MAX362CSE+ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Notes de conception
Do not treat the MAX361 and MAX362 as interchangeable without reviewing the default switch state. The MAX362 has four normally open channels, whereas the MAX361 has four normally closed channels. Although the devices share the precision quad SPST family positioning, the different default connection states can reverse the behavior of reset, fault, or power-up conditions.
Use the MAX362 pin-description table in the manufacturer datasheet to assign every analog and control pin in the 16-pin SOIC footprint. Keep the analog route compact, connect all device grounds to a continuous low-impedance plane, and separate control traces from sensitive signal paths. Avoid routing high-current or high-voltage switching traces beneath the analog pins.
Estimated attenuation depends on the complete source impedance and the switch's 85-ohm on resistance. Using a 50-ohm source, the switch alone forms 135 ohms before the load is included; the resulting divider must be checked against the required signal amplitude. Confirm capacitance, bandwidth, and switching time in the datasheet when routing fast or high-amplitude signals.
Informations de conformité
The available product information does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this precision analog switch is not identified as an automotive-qualified device.