MAX365CPE+ - Quad SPST Analog Switch | Maxim Integrated
MPN: MAX365CPE+ ✓ نشطMAX365CPE+ نظرة عامة
An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The MAX365CPE+ belongs to the analog switch and multiplexer hierarchy, providing four independent switching paths rather than multiplexing several inputs onto a shared output. Each switch is normally open, so the connected state exists only when the control input commands the device, which helps prevent unintended signal paths during power-up and reset conditions.
The main engineering benefits of the MAX365 family are its low on-resistance, tightly matched channels, and flat resistance behavior. Matching within 2 ohm minimizes gain error between channels, while the maximum 9 ohm variation over the signal range reduces the gain error that would otherwise appear as the analog level changes. These characteristics are particularly useful in instrumentation, test systems, data converters, and precision signal-conditioning boards where repeatable channel impedance supports accurate measurements.
The MAX365CPE+ uses four independently controlled switches. Because the control logic operates from the same single supply as the analog switches, only one supply rail is required for basic operation. Keep control inputs at valid logic levels whenever an analog input may exceed the supply range, and confirm the absolute maximum ratings in the manufacturer datasheet before applying signals above the switch supply voltage.
Typical uses include sensor selection, sample-and-hold front ends, test-point routing, programmable gain stages, and isolation of external analog inputs. The four switch channels can also be combined for wider routing functions, although the control architecture must keep the individual on-resistance values in mind when several closed channels share the same signal path.
The 16-pin PDIP package is appropriate for through-hole prototype boards, legacy control systems, and industrial assemblies that favor a socketed or readily inspected package. Its relatively large pin pitch simplifies probing and rework compared with fine-pitch surface-mount alternatives. During layout, route analog traces away from control and clock lines, and place the device close to the switched nodes to minimize parasitic pickup in high-impedance circuits.
This page consolidates the manufacturer product information with practical routing guidance, precision-impedance considerations, package details, and ordering guidance for engineers evaluating the MAX365CPE+ in analog signal-path designs.
بدائل مباشرة لـ MAX365CPE+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
MAX365CPE
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX365CPE+ الحدود القصوى والخصائص الكهربائية
| Number of Switches | 4 |
| Switch Configuration | 1:1 |
| Switch Type | Single-pole, single-throw (SPST) |
| Normal State | Normally open (NO) |
| On-Resistance | Less than 85 ohm |
| Listed On-Resistance Rating | 85 ohm |
| Channel-to-Channel On-Resistance Matching | Within 2 ohm |
| On-Resistance Variation Over Analog Signal Range | 9 ohm maximum |
| Number of Control Inputs | 4 |
| العلبة | 16-pin PDIP |
| نوع التركيب | Through-hole |
| حالة دورة الحياة | Production |
دليل تكوين أطراف MAX365CPE+ 16-pin pdip
تكوين الأطراف لـ MAX365CPE+ (حزمة 16-pin pdip). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MAX365CPE+.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MAX365CPE+ مناسب لـ 6 التطبيقs: Four-Channel Sensor Selector, Programmable Gain and Attenuator Networks, Test-Point Signal Routing, Sample-and-Hold Front Ends, External Signal Isolation, Industrial Control and Data Acquisition.
Four-Channel Sensor Selector
The MAX365CPE+ fits a four-sensor selection network where only one sensor should drive a shared amplifier or converter input at a time. Each normally open SPST channel keeps the three unselected paths isolated, while the 2 ohm channel-to-channel matching limits resistance-driven gain differences between selected sensors. The manufacturer-specified on-resistance below 85 ohm also keeps the switched impedance low relative to many high-impedance sensors. Place the switch close to the shared input, keep the routing loop compact, and allow sufficient settling time after changing channels so that charge redistribution and switching transients do not become measurement errors.
موصى به
Programmable Gain and Attenuator Networks
The MAX365CPE+ can route signals through precision resistor networks to implement programmable gain, attenuation, or calibration paths. Its on-resistance stays below 85 ohm, and the family limits on-resistance variation to 9 ohm across the analog signal range, helping reduce signal-dependent gain error. Channel matching within 2 ohm is particularly useful when two switch positions establish a ratio. Design the resistance values so switch resistance remains a small percentage of the total path impedance, and verify settling behavior at the highest operating bandwidth before relying on fast calibration sequences.
موصى به
Test-Point Signal Routing
The MAX365CPE+ is well suited to test-point routing in automatic test equipment, interface boards, and production fixtures. Four independent 1:1 paths can connect a DUT node to different measurement resources without sharing a multiplexer output. The normally open configuration prevents unintended paths during fixture reset, while matched on-resistance helps maintain comparable measurement impedance across channels. Keep sensitive analog traces away from digital control wiring, use short connections to the test points, and confirm that the 85 ohm switch resistance is acceptable relative to the input impedance of the connected instrument.
موصى به
Sample-and-Hold Front Ends
The MAX365CPE+ can select among four input sources feeding a sample-and-hold amplifier or analog-to-converter front end. Its matched on-resistance reduces gain differences between input channels, and the flat resistance specification limits level-dependent error. Because the switch remains in the signal path during acquisition, include its contribution to settling time, charge injection, and acquisition aperture in the system budget. The 16-pin PDIP package also makes the device convenient for through-hole instrumentation prototypes where probing and rework speed are more important than board area.
موصى به
External Signal Isolation
The MAX365CPE+ can isolate external inputs, sensor outputs, or auxiliary signals from a shared analog processing chain. Because the channels are normally open, disconnected sources remain separated until a control input intentionally closes the selected path. This arrangement prevents a high-impedance unused source from loading the active channel. For isolation to remain effective, control pins must never float, and externally applied voltages must stay within the absolute maximum ratings in the manufacturer data sheet, particularly when the switch is unpowered.
موصى به
Industrial Control and Data Acquisition
The MAX365CPE+ fits industrial control boards that must select among several analog inputs before conversion or comparison. The four dedicated SPST paths simplify control firmware and avoid the multiplexing time required to cycle one shared path. Through-hole assembly in a 16-pin PDIP package supports prototype, legacy, and serviceable industrial boards. Validate the control logic levels, supply range, and off-state behavior against the system requirements, and route the analog inputs directly to the device to minimize noise picked up on long PCB traces.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MAX365CPE+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MAX365CPE |
|---|---|---|
| Manufacturer | Maxim Integrated | Maxim Integrated |
| Package | 16-pin PDIP | 16-pin PDIP |
| Number of Switches | 4 | 4 |
| Switch Configuration | 1:1 | 1:1 |
| Switch Type | SPST | SPST |
| Normal State | Normally open | Normally open |
| On-Resistance | Less than 85 ohm | Less than 85 ohm |
| Channel Matching | Within 2 ohm | Within 2 ohm |
| On-Resistance Variation | 9 ohm maximum over the analog signal range | 9 ohm maximum over the analog signal range |
| Lifecycle Status | Production | MAX365 family listed as production |
أبرز الفروقات
- Dedicated normally open signal paths (مقابلMAX365CPE)
- Matched switch impedance (مقابلMAX365CPE)
- Flat on-resistance characteristic (مقابلMAX365CPE)
ملاحظات التصميم
Treat the MAX365CPE+ on-resistance as part of the signal-path impedance. Its maximum on-resistance is below 85 ohm, and channel-to-channel matching is within 2 ohm. For high-impedance sources, minimize trace length between the source and switched node, keep the switched node on a contiguous ground reference, and avoid routing the analog path beneath control signals. If resistance variation contributes materially to gain error, compensate it through calibration rather than assuming identical channel impedance.
Do not allow control inputs to float. The MAX365CPE+ uses normally open switches, but floating control inputs can produce indeterminate states, unwanted charge transfer, or unexpected connection of an external signal. Use defined logic states during reset and power sequencing, and ensure that any signal present while the device is unpowered remains within the absolute maximum ratings listed in the manufacturer data sheet.
The 16-pin PDIP package is optimized for through-hole rather than high-density surface-mount assembly. Place the device near the source and destination nodes to minimize parasitic inductance and capacitance, provide a low-impedance ground connection, and keep analog traces clear of switching-control and clock routing. If the PCB is assembled by machine, verify lead pitch, hole diameter, and solderability against the package drawing before layout release.
Do not share a single switched analog trace with unrelated high-speed digital nets. Although the MAX365CPE+ is an analog switch, its control transitions can produce charge injection on the switched node. Short control traces, adequate ground referencing, and separation from clock and switching-supply paths reduce coupling. In precision front ends, add a settling period after changing a channel and evaluate the resulting error against the required measurement resolution.
معلومات الامتثال
The manufacturer identifies the MAX365 family as production. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not available in the referenced product information and must be confirmed with the manufacturer.