Maxim Integrated

MAX365CPE+ - Quad SPST Analog Switch | Maxim Integrated

MPN: MAX365CPE+ ✓ Aktif
Less than 85 ohm Rds(on) 16-pin PDIP Package
MOQ: 1 |

MAX365CPE+ Genel Bakış

The Maxim Integrated MAX365CPE+ is a precision quad single-pole, single-throw analog switch with four normally open switches, a 1:1 configuration, and a 16-pin PDIP package. Its on-resistance is specified below 85 ohm, with channel-to-channel matching maintained within 2 ohm and on-resistance variation limited to 9 ohm across the analog signal range. These characteristics make the device suitable for precision analog routing where consistent channel resistance simplifies calibration of downstream measurement and signal-conditioning circuits.

An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The MAX365CPE+ belongs to the analog switch and multiplexer hierarchy, providing four independent switching paths rather than multiplexing several inputs onto a shared output. Each switch is normally open, so the connected state exists only when the control input commands the device, which helps prevent unintended signal paths during power-up and reset conditions.

The main engineering benefits of the MAX365 family are its low on-resistance, tightly matched channels, and flat resistance behavior. Matching within 2 ohm minimizes gain error between channels, while the maximum 9 ohm variation over the signal range reduces the gain error that would otherwise appear as the analog level changes. These characteristics are particularly useful in instrumentation, test systems, data converters, and precision signal-conditioning boards where repeatable channel impedance supports accurate measurements.

The MAX365CPE+ uses four independently controlled switches. Because the control logic operates from the same single supply as the analog switches, only one supply rail is required for basic operation. Keep control inputs at valid logic levels whenever an analog input may exceed the supply range, and confirm the absolute maximum ratings in the manufacturer datasheet before applying signals above the switch supply voltage.

Typical uses include sensor selection, sample-and-hold front ends, test-point routing, programmable gain stages, and isolation of external analog inputs. The four switch channels can also be combined for wider routing functions, although the control architecture must keep the individual on-resistance values in mind when several closed channels share the same signal path.

The 16-pin PDIP package is appropriate for through-hole prototype boards, legacy control systems, and industrial assemblies that favor a socketed or readily inspected package. Its relatively large pin pitch simplifies probing and rework compared with fine-pitch surface-mount alternatives. During layout, route analog traces away from control and clock lines, and place the device close to the switched nodes to minimize parasitic pickup in high-impedance circuits.

This page consolidates the manufacturer product information with practical routing guidance, precision-impedance considerations, package details, and ordering guidance for engineers evaluating the MAX365CPE+ in analog signal-path designs.

Drop-in alternatifler için MAX365CPE+ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

MAX365CPE

✅ Yerleştirme
📦 16-pin PDIP
Non-plus ordering option of the same MAX365 family; electrical function and 16-pin PDIP outline match, while lead-finish and ordering requirements may differ by 0 percent in function

📋 Katalogda Olmayan Referans Alternatifi

MAX365CPE+ Maksimum Değerlendirmeler & Elektriksel Özellikler

Number of Switches 4
Switch Configuration 1:1
Switch Type Single-pole, single-throw (SPST)
Normal State Normally open (NO)
On-Resistance Less than 85 ohm
Listed On-Resistance Rating 85 ohm
Channel-to-Channel On-Resistance Matching Within 2 ohm
On-Resistance Variation Over Analog Signal Range 9 ohm maximum
Number of Control Inputs 4
Paket 16-pin PDIP
Montaj Türü Through-hole
Yaşam Döngüsü Durumu Production

MAX365CPE+ 16-pin pdip Pin Yapısı Kılavuzu

MAX365CPE+ (16-pin pdip paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

16-pin pdip paket pin çizelgesi için MAX365CPE+

Ayrıntılı pin çıkış verisi mevcut değil: MAX365CPE+.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

MAX365CPE+ için uygundur 6 uygulamas: Four-Channel Sensor Selector, Programmable Gain and Attenuator Networks, Test-Point Signal Routing, Sample-and-Hold Front Ends, External Signal Isolation, Industrial Control and Data Acquisition.

🧩

Four-Channel Sensor Selector

The MAX365CPE+ fits a four-sensor selection network where only one sensor should drive a shared amplifier or converter input at a time. Each normally open SPST channel keeps the three unselected paths isolated, while the 2 ohm channel-to-channel matching limits resistance-driven gain differences between selected sensors. The manufacturer-specified on-resistance below 85 ohm also keeps the switched impedance low relative to many high-impedance sensors. Place the switch close to the shared input, keep the routing loop compact, and allow sufficient settling time after changing channels so that charge redistribution and switching transients do not become measurement errors.

📡

Programmable Gain and Attenuator Networks

The MAX365CPE+ can route signals through precision resistor networks to implement programmable gain, attenuation, or calibration paths. Its on-resistance stays below 85 ohm, and the family limits on-resistance variation to 9 ohm across the analog signal range, helping reduce signal-dependent gain error. Channel matching within 2 ohm is particularly useful when two switch positions establish a ratio. Design the resistance values so switch resistance remains a small percentage of the total path impedance, and verify settling behavior at the highest operating bandwidth before relying on fast calibration sequences.

🔧

Test-Point Signal Routing

The MAX365CPE+ is well suited to test-point routing in automatic test equipment, interface boards, and production fixtures. Four independent 1:1 paths can connect a DUT node to different measurement resources without sharing a multiplexer output. The normally open configuration prevents unintended paths during fixture reset, while matched on-resistance helps maintain comparable measurement impedance across channels. Keep sensitive analog traces away from digital control wiring, use short connections to the test points, and confirm that the 85 ohm switch resistance is acceptable relative to the input impedance of the connected instrument.

📈

Sample-and-Hold Front Ends

The MAX365CPE+ can select among four input sources feeding a sample-and-hold amplifier or analog-to-converter front end. Its matched on-resistance reduces gain differences between input channels, and the flat resistance specification limits level-dependent error. Because the switch remains in the signal path during acquisition, include its contribution to settling time, charge injection, and acquisition aperture in the system budget. The 16-pin PDIP package also makes the device convenient for through-hole instrumentation prototypes where probing and rework speed are more important than board area.

🛡️

External Signal Isolation

The MAX365CPE+ can isolate external inputs, sensor outputs, or auxiliary signals from a shared analog processing chain. Because the channels are normally open, disconnected sources remain separated until a control input intentionally closes the selected path. This arrangement prevents a high-impedance unused source from loading the active channel. For isolation to remain effective, control pins must never float, and externally applied voltages must stay within the absolute maximum ratings in the manufacturer data sheet, particularly when the switch is unpowered.

🏭

Industrial Control and Data Acquisition

The MAX365CPE+ fits industrial control boards that must select among several analog inputs before conversion or comparison. The four dedicated SPST paths simplify control firmware and avoid the multiplexing time required to cycle one shared path. Through-hole assembly in a 16-pin PDIP package supports prototype, legacy, and serviceable industrial boards. Validate the control logic levels, supply range, and off-state behavior against the system requirements, and route the analog inputs directly to the device to minimize noise picked up on long PCB traces.

Önerilen Ürünler Özeti

MAX365CPE+ Maxim Integrated Kullanıldığı Yer: Four-Channel Sensor Selector, Programmable Gain and Attenuator Networks, Test-Point Signal Routing, Sample-and-Hold Front Ends, External Signal Isolation, Industrial Control and Data Acquisition MAX365CPE Same-family 16-pin PDIP ordering option Kullanıldığı Yer: Four-Channel Sensor Selector, Programmable Gain and Attenuator Networks, Test-Point Signal Routing, Sample-and-Hold Front Ends, External Signal Isolation, Industrial Control and Data Acquisition
What is the MAX365CPE+?
The MAX365CPE+ is a precision quad SPST analog switch from Maxim Integrated with four normally open channels in a 16-pin PDIP package. According to the manufacturer product page, it provides on-resistance below 85 ohm, channel matching within 2 ohm, and on-resistance variation of no more than 9 ohm across the analog signal range. It is intended for routing analog signals where repeatable channel impedance is more important than very high switching speed.
How many switches does the MAX365CPE+ contain?
The MAX365CPE+ contains four independent single-pole, single-throw analog switches in a 1:1 configuration. All four channels are normally open, meaning each signal path is disconnected until its associated control input commands the switch closed. Distributor listings describe the device as a 4-circuit, 1:1 analog switch, while the manufacturer describes it as a precision quad SPST analog switch family.
What is the on-resistance of the MAX365CPE+?
The MAX365CPE+ has an on-resistance below 85 ohm, with the distributed-part listing showing an 85 ohm rating. The manufacturer also specifies channel-to-channel matching within 2 ohm and a maximum change of 9 ohm across the analog signal range. These figures make the switch suitable for instrumentation and signal-conditioning paths where a large resistance change with signal level would increase gain error.
Is the MAX365CPE+ normally open or normally closed?
The MAX365CPE+ uses four normally open switches. According to the MAX365 manufacturer page, the MAX364 family member uses normally closed channels, while the MAX365 uses normally open channels. The normally open behavior is useful when disconnected analog inputs must remain isolated during reset or power sequencing, although the control inputs still have to remain in valid logic states.
Where can I download the MAX365CPE+ datasheet PDF?
The official MAX365 product page at Analog Devices provides the MAX365 data sheet and product documentation. The MAX365CPE+ is the 16-pin PDIP ordering option of the MAX365 family, and the manufacturer product page identifies the family as production. Use the data-sheet link on that page for the pin-description table, absolute maximum ratings, recommended operating conditions, and switching waveforms.
Where can I find the MAX365CPE+ pinout?
The MAX365CPE+ pinout is documented in the pin-description table of the MAX365 manufacturer data sheet. The package is a 16-pin PDIP with four switch paths and four control inputs, plus supply and ground connections. Use the data-sheet table rather than relying on a generic 16-pin DIP drawing because signal, control, and supply assignments are specific to the MAX365 family.
What is the best drop-in replacement for the MAX365CPE+?
The closest confirmed ordering alternative is the MAX365CPE, which represents the non-plus ordering option of the same MAX365 family and uses the same 16-pin PDIP outline. Confirm the temperature grade, lead finish, and purchasing requirements against the original assembly documentation before substitution. The Request a Quote form on this page can be used to verify current sourcing for both orderable variants.
Can the MAX365CPE replace a MAX365CPE+?
The MAX365CPE can generally serve as a functional substitute for the MAX365CPE+ because both identify 16-pin PDIP orderings of the MAX365 quad SPST analog-switch family. The ordering suffix must still be checked against temperature-range, lead-finish, and procurement requirements. Confirm those details in the manufacturer data sheet and current part-selection table before releasing production artwork.
MAX365CPE+ vs MAX364CPE+ - which switch should I choose?
Choose the MAX365CPE+ when disconnected, normally open behavior is required; the MAX364 family member provides normally closed channels. Both belong to the same precision quad SPST switch family and share the low-resistance matching concept, but their default signal-path states differ. The state requirement should be decided first because an external pull network can change the effective behavior of the selected part.
When should I choose the MAX365CPE+ over a multiplexer IC?
Choose the MAX365CPE+ when each of four signal paths must remain electrically independent and can be switched separately. A multiplexer combines multiple inputs into a shared output, while the MAX365 provides four dedicated 1:1 paths. The MAX365 is therefore a better fit for sensor selection, signal isolation, and test-point routing where simultaneous connections or per-channel impedance control are required.
Is the MAX365CPE+ suitable for precision test and measurement systems?
Yes, the MAX365CPE+ is suitable for precision test and measurement systems because its on-resistance is below 85 ohm, channels match within 2 ohm, and resistance changes by no more than 9 ohm over the analog signal range. These characteristics reduce channel-dependent gain error. Keep leakage, switching-time, and overvoltage conditions within the manufacturer limits for the specific measurement bandwidth.
What application uses four normally open analog switches?
A typical application is a four-sensor selector in which one amplifier or converter input is connected to only one of four sensing elements at a time. The normally open channels prevent unintended sensor paths from remaining connected, and the 2 ohm channel matching helps limit gain differences between selected sensors. Firmware should still account for settling time and any switching transient at the shared input.
Where can I buy the MAX365CPE+ online?
Use the Request a Quote form on this page to request the MAX365CPE+, current lead time, and available order quantities. The manufacturer identifies the MAX365 family as production, and the part is offered in a 16-pin PDIP package. A complete quote response helps confirm whether the quantity, lead finish, and sourcing requirements match your assembly schedule.
What is the price of the MAX365CPE+?
Current pricing for the MAX365CPE+ should be requested through the Request a Quote form on this page because transaction terms, quantity breaks, and sourcing availability can change over time. The manufacturer product page presents list-price information for the MAX365 family, but the final quote should reflect the exact 16-pin PDIP ordering code and the quantity required for your build.
What is the lead time for the MAX365CPE+?
Request the current lead time through the Request a Quote form on this page and include your required quantity and target delivery date. The manufacturer lists the MAX365 family as production, but production status alone does not establish available inventory or a delivery commitment for a specific order. The quote confirmation provides the appropriate schedule for your production plan.
Is the MAX365CPE+ in stock?
Stock for the MAX365CPE+ is confirmed through the Request a Quote form on this page. The manufacturer identifies the MAX365 family as production, while distributor inventory for the exact 16-pin PDIP ordering code changes independently. Submit the required quantity and target date so the current sourcing and schedule can be checked against your assembly requirements.
What are the key specifications of the MAX365CPE+ that engineers should know?
The essential MAX365CPE+ specifications are four normally open SPST switches, a 1:1 configuration, on-resistance below 85 ohm, channel matching within 2 ohm, and maximum on-resistance variation of 9 ohm over the analog signal range. The device uses a 16-pin PDIP package. According to the manufacturer product page, the MAX365 family is a production precision quad SPST analog switch.

Mühendislik referans verileri: MAX365CPE+ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the MAX365CPE+ when a design needs four independent, normally open analog paths and values matched, low-impedance routing. It is especially appropriate for sensor selection, precision gain calibration, test-point routing, and acquisition front ends where the four channels must not share a multiplexer output. The 16-pin PDIP package also makes it convenient for through-hole prototypes, industrial boards, and serviceable assemblies. The MAX365CPE is the same-family 16-pin PDIP ordering option and is the practical alternative when procurement or lead-finish requirements favor that variant. Multiplexer ICs such as the MAX359CPE+ or DG509ACJ+ are not drop-in substitutes for this part because their multiplexing architecture and pin assignments differ from the four dedicated 1:1 paths in the MAX365. Confirm supply voltage, logic thresholds, leakage, switching time, and absolute maximum ratings from the manufacturer data sheet before committing a design.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün MAX365CPE
Manufacturer Maxim Integrated Maxim Integrated
Package 16-pin PDIP 16-pin PDIP
Number of Switches 4 4
Switch Configuration 1:1 1:1
Switch Type SPST SPST
Normal State Normally open Normally open
On-Resistance Less than 85 ohm Less than 85 ohm
Channel Matching Within 2 ohm Within 2 ohm
On-Resistance Variation 9 ohm maximum over the analog signal range 9 ohm maximum over the analog signal range
Lifecycle Status Production MAX365 family listed as production

Ana Farklılayıcılar

  • Dedicated normally open signal paths (karşılaştırma:MAX365CPE)
  • Matched switch impedance (karşılaştırma:MAX365CPE)
  • Flat on-resistance characteristic (karşılaştırma:MAX365CPE)

Tasarım Notları

Treat the MAX365CPE+ on-resistance as part of the signal-path impedance. Its maximum on-resistance is below 85 ohm, and channel-to-channel matching is within 2 ohm. For high-impedance sources, minimize trace length between the source and switched node, keep the switched node on a contiguous ground reference, and avoid routing the analog path beneath control signals. If resistance variation contributes materially to gain error, compensate it through calibration rather than assuming identical channel impedance.

Do not allow control inputs to float. The MAX365CPE+ uses normally open switches, but floating control inputs can produce indeterminate states, unwanted charge transfer, or unexpected connection of an external signal. Use defined logic states during reset and power sequencing, and ensure that any signal present while the device is unpowered remains within the absolute maximum ratings listed in the manufacturer data sheet.

The 16-pin PDIP package is optimized for through-hole rather than high-density surface-mount assembly. Place the device near the source and destination nodes to minimize parasitic inductance and capacitance, provide a low-impedance ground connection, and keep analog traces clear of switching-control and clock routing. If the PCB is assembled by machine, verify lead pitch, hole diameter, and solderability against the package drawing before layout release.

Do not share a single switched analog trace with unrelated high-speed digital nets. Although the MAX365CPE+ is an analog switch, its control transitions can produce charge injection on the switched node. Short control traces, adequate ground referencing, and separation from clock and switching-supply paths reduce coupling. In precision front ends, add a settling period after changing a channel and evaluate the resulting error against the required measurement resolution.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The manufacturer identifies the MAX365 family as production. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not available in the referenced product information and must be confirmed with the manufacturer.

Veri doğrulanma tarihi: 2026-11-09 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

MAX365CPE+ MAX365CPE+ datasheet MAX365CPE+ datasheet pdf MAX365CPE+ pinout Maxim Integrated MAX365CPE+ MAX365CPE+ equivalent MAX365CPE+ replacement MAX365CPE+ cross reference MAX365CPE+ price MAX365CPE+ stock MAX365 16-pin PDIP analog switch MAX365CPE+ precision SPST switch MAX365CPE+ sensor selection circuit MAX365CPE+ vs MAX365CPE

İlgili Bileşenler ve Terimler

Maxim Integrated Analog Devices MAX365CPE+ MAX365CPE MAX364 MAX365 MAX359CPE+ DG509ACJ+ precision analog switch analog switch IC multiplexer single-pole single-throw SPST switch normally open switch 1:1 switch configuration on-resistance channel matching signal leakage 16-pin PDIP PDIP package through-hole package sensor selection test-point routing sample-and-hold front end gain calibration
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle