MC14018BF - 5-Stage Presettable Counter | onsemi
MPN: MC14018BF ✓ نشطMC14018BF نظرة عامة
A Johnson counter is a synchronous sequential-logic circuit whose output stages feed the next stage in a ring configuration. It belongs to the counter and divider hierarchy within CMOS logic ICs. Unlike a conventional binary ripple counter, the MC14018B implements decade-oriented counting with individually available outputs and separate asynchronous controls for preset and reset. Presetting occurs when the preset-enable input is driven to a logic 1, while the counter can be reset asynchronously through its dedicated reset input.
The principal functional characteristics include five Johnson counter stages, positive-edge clock operation, asynchronous preset and reset functions, and five decoded outputs suitable for driving five sequential stages. The asynchronous control paths allow an external system to establish a known count immediately rather than waiting for a clock edge. This is useful when synchronization with another subsystem or a system initialization sequence is required.
The MC14018B is implemented as a CMOS logic device, placing it within the low-dropout and low-power digital IC family associated with battery-powered and low-voltage systems. The counter maintains state across clock transitions and can divide an input clock into lower-frequency or sequential timing signals. Its decoded outputs can also act as a five-position ring sequence for sequencing multiple loads or system phases.
Typical applications include programmable frequency dividers, digital timing generators, cyclic sequence counters, industrial control logic, and clock-domain distribution. It can be used where a compact five-step sequence is needed without implementing the counter from individual flip-flops. Because preset and reset are asynchronous, the device can also initialize a timing sequence after reset while the surrounding system is settling.
PCB implementation requires attention to unused inputs and signal transitions. Follow the onsemi MC14018B datasheet pin-description table for every connection, keep the clock and control traces short, and place any decoupling capacitor close to the supply pins. Because transition behavior can influence adjacent CMOS nets, avoid routing high-current or high-speed signals beside the counter outputs and use a defined reset strategy during power-up.
This page combines the functional description, pin and package guidance, application analysis, design notes, and sourcing information for the MC14018BF. The comparison section distinguishes the 16-pin plastic DIP MC14018BF from other MC14018B package and temperature options, helping engineers determine when a footprint or qualification change is required before substitution.
بدائل مباشرة لـ MC14018BF — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلMC14018BF الحدود القصوى والخصائص الكهربائية
| Counter Type | Johnson counter / divide-by-N counter |
| Number of Counter Stages | 5 stages |
| Clock Edge | Positive-going edge |
| Counting Mode | Synchronous |
| Preset Control | Asynchronous, active logic 1 preset enable |
| Reset Control | Asynchronous |
| Decoded Outputs | 5 outputs |
| Logic Family | CMOS |
| Temperature Grade | Military |
| العلبة | 16-pin plastic DIP |
| عدد الأطراف | 16 pins |
| Terminal Type | Gull-wing |
| Package Shape | Rectangular |
| نوع التركيب | Through-hole |
دليل تكوين أطراف MC14018BF rectangular
تكوين الأطراف لـ MC14018BF (حزمة rectangular). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MC14018BF.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MC14018BF مناسب لـ 6 التطبيقs: Programmable Frequency Divider, Five-Step Digital Sequencer, Industrial Timing Controller, Clock Divider and Rate Selector, Test and Measurement Trigger Sequencer, Battery-Powered Digital Logic.
Programmable Frequency Divider
The MC14018BF fits programmable divider designs because its five Johnson stages advance synchronously on each positive-going clock edge and expose decoded count outputs. According to the onsemi MC14018B datasheet, asynchronous preset control can establish an initial count without waiting for a clock transition. This makes the device useful when an external controller must select a division interval during initialization. Place the device between the source clock and divider output, observe the input clock’s maximum frequency, and apply a defined reset state before enabling the system clock.
موصى به
Five-Step Digital Sequencer
The MC14018BF provides five decoded outputs that can represent successive states in a cyclic control sequence. The synchronous positive-edge counting behavior keeps the sequence aligned with a master clock, while the asynchronous reset input allows the sequence to return to a defined start condition. This arrangement can replace several discrete flip-flops when five ordered phases are sufficient. Confirm the maximum clock frequency for the selected supply voltage and use the manufacturer output truth table to assign each decoded output to the intended system phase.
موصى به
Industrial Timing Controller
The MC14018BF is suitable for industrial timing and sequencing logic that requires repeatable five-position counting with external initialization. Its asynchronous preset and reset paths allow a supervisory circuit to establish a known state during equipment startup, while the clock input provides the timing reference for the sequence. Use this arrangement only after checking the device’s specified supply-voltage and temperature limits against the industrial environment. A deterministic reset supervisor should control the reset input so the timing state is established before normal operation begins.
موصى به
Clock Divider and Rate Selector
The MC14018BF can divide a reference clock into selectable timing intervals when the preset function is combined with external control logic. The onsemi MC14018B datasheet confirms that the five counter stages increment synchronously, avoiding the accumulated propagation delay associated with a ripple-counter arrangement. A decoded output can therefore become a lower-rate enable pulse for another subsystem. Validate the source-clock amplitude, frequency, and supply voltage against the device limits, and keep the selected output away from high-current switching paths to reduce timing disturbance.
موصى به
Test and Measurement Trigger Sequencer
The MC14018BF can create a repeatable five-step trigger sequence in test equipment or measurement systems. Positive-edge counting makes every decoded output change in a controlled order, and asynchronous reset allows the sequence to be restarted at a defined instant. The counter can therefore coordinate measurement phases, instrument settling intervals, or acquisition stages. Keep the clock distribution isolated from sensitive analog paths, use a low-impedance reset driver, and follow the onsemi MC14018B datasheet when assigning outputs to avoid unintended combinations during startup.
موصى به
Battery-Powered Digital Logic
The MC14018BF can replace multiple counter flip-flops in a battery-powered control path where a compact fixed five-state sequence is needed. Its five decoded outputs provide visible count states without requiring a microcontroller to poll every phase. Before selecting it for low-power equipment, verify the operating-voltage range and quiescent-current limits in the onsemi MC14018B datasheet. Enable the counter only when required if the surrounding design permits clock gating, and use a defined reset or preset command to prevent extra transitions during power restoration.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MC14018BF — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Package | 16-pin plastic DIP |
| Brand | onsemi |
| Counter Stages | 5 stages |
| Counter Type | Johnson counter / divide-by-N counter |
| Clock Edge | Positive-going edge |
| Counting Mode | Synchronous |
| Preset Control | Asynchronous, active logic 1 preset enable |
| Reset Control | Asynchronous |
| Decoded Outputs | 5 outputs |
| Logic Family | CMOS |
أبرز الفروقات
- Five decoded states from one counter package (مقابلDiscrete flip-flop counter implementation)
- Synchronous positive-edge progression (مقابلAsynchronous ripple-counter implementation)
- Asynchronous preset and reset initialization (مقابلSoftware-initialized counter)
ملاحظات التصميم
Do not treat every MC14018B suffix as a drop-in equivalent for MC14018BF. MC14018BF uses a 16-pin plastic DIP footprint, while MC14018BD and MC14018BDG are identified as surface-mount SOIC options. Their land patterns are not interchangeable. Before selecting another suffix, compare the manufacturer pin-description table, package drawing, temperature range, and electrical timing characteristics; a similar counter function alone is insufficient for PCB compatibility.
Use the onsemi MC14018B pin-description table to assign all 16 package pins and place the counter close to the circuits that consume its decoded outputs. Keep the clock, preset, and reset nets short, and provide the supply decoupling recommended by the manufacturer. Since CMOS inputs can respond to nearby switching activity, avoid routing high-current or fast-edge traces parallel to the counter outputs, particularly in systems containing inductors or switching regulators.
Establish the counter’s initial state with a controlled reset pulse and release reset only when the clock source and control logic are stable. The asynchronous reset path can change the count without a clock edge, so uncontrolled reset release can generate an unintended decoded transition. If the source clock is noisy or has a slow edge, condition it before entering the counter and verify timing at the highest intended operating frequency and supply voltage.
معلومات الامتثال
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were identified for MC14018BF.