Motorola

MC14577CP - Dual Video Amplifier | Motorola | DIP-8

MPN: MC14577CP ✗ انتهى عمره الإنتاجي
8-PDIP Package
الحد الأدنى للطلب: 1 |

MC14577CP نظرة عامة

The Motorola MC14577CP is a dual video amplifier integrated circuit packaged in an 8-pin DIP. The device is listed for video amplifier and related signal-processing applications, and distributor listings identify it as a two-channel video amplifier with the package designation 8-PDIP. The MC14577CP is therefore primarily intended for applications requiring two video signal channels in a conventional through-hole package.

A video amplifier is an analog integrated circuit used to condition composite, differential, or other video signals before they reach a display, monitor, video processing block, or transmission circuit. In the broader electronics hierarchy, the MC14577CP belongs to the class of amplifier ICs, specifically video amplifiers and modules, rather than being a discrete transistor or a general-purpose digital interface IC. Its dual-channel architecture can reduce the number of separate amplifier packages required in equipment that carries two related video signals.

The MC14577CP is associated with the Motorola MC14577 video-amplifier family and is commonly encountered in legacy television, monitor, video-peripheral, and service-equipment designs. The 8-PDIP format makes the device convenient for through-hole prototypes, repair work, and equipment where a leaded package is preferred over a surface-mount package. The “CP” suffix identifies this particular ordering variant and should be retained when comparing it with other family members.

Because the device is an older video amplifier, design work should begin with the manufacturer datasheet and the system’s signal levels, impedance requirements, bandwidth expectations, supply arrangement, and allowable distortion. The MC14577CP may be especially relevant when maintaining or reproducing older analog video hardware rather than designing a new compact surface-mount product. The key engineering question is whether the original board requires the MC14577CP’s channel count, gain behavior, supply voltage, input/output impedance, and output-drive capability.

In a typical video path, the MC14577CP would sit between a video source and downstream circuitry, with external resistors and capacitors setting gain, bandwidth, coupling, or compensation as required by the application. Its through-hole package supports straightforward prototyping, but designers should still observe the datasheet’s decoupling and grounding recommendations to avoid instability, excessive noise, or channel-to-channel interaction.

This product summary combines package and category information with practical replacement guidance. Because equivalent availability is limited, engineers should verify the pinout, electrical limits, and signal-chain requirements directly against the MC14577CP datasheet before substituting any part. For current commercial availability, use the Request a Quote form on this page rather than relying on historical distributor pricing.

بدائل مباشرة لـ MC14577CP — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

EL4457C

✅ بديل مباشر
📦 DIP-8
Dual video amplifier in DIP-8; documented bandwidth and push-pull output differ from MC14577CP, requiring pin and gain-network verification

📋 بديل مرجعي (غير موجود في الكتالوج)

MC14577CP الحدود القصوى والخصائص الكهربائية

Product Type Video amplifier IC
Number of Video Channels 2
العلبة 8-PDIP
نوع التركيب Through-hole
Manufacturer Motorola
حالة RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable
Lead-Free Status unknown

دليل تكوين أطراف MC14577CP 8-pdip

تكوين الأطراف لـ MC14577CP (حزمة 8-pdip). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 8-pdip لـ MC14577CP

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MC14577CP.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

MC14577CP مناسب لـ 6 التطبيقs: Legacy Television Video Signal Conditioning, CRT Monitor Video Amplification, Analog Video Interface Repair, Video Test Equipment Signal Paths, Video Distribution Front Ends, Retrofit and Maintenance Platforms.

📺

Legacy Television Video Signal Conditioning

The MC14577CP fits legacy television service work when the original board uses a dual video amplifier in an 8-PDIP package. Its two channels can condition related video paths while preserving the established through-hole construction and component arrangement. The designer should reproduce the original feedback and compensation values, confirm the amplifier’s allowed operating region, and account for any signal attenuation or gain differences introduced by the surrounding source, load, and coupling networks.

🖥️

CRT Monitor Video Amplification

The MC14577CP is applicable to legacy CRT monitor circuitry where separate video channels drive downstream display stages through passive networks. The 8-PDIP format simplifies repairs on existing through-hole boards, while the dual-channel architecture can support paired luminance and chrominance paths when the original design uses them in that manner. Exact channel assignment and signal conditioning must follow the original schematic and the MC14577CP pinout, because the package confirms pin count but not individual lead functions.

🔧

Analog Video Interface Repair

The MC14577CP is useful in repair and modernization projects that retain an analog video interface but need to replace a failed dual amplifier in the original 8-PDIP footprint. Its suitability depends on reproducing the original gain distribution and checking the amplifier’s input and output impedances against the connected source and load. A replacement decision should compare not only the package, but also DC operating points, signal swing, bandwidth, output-drive capability, and stability with the actual external component values.

📡

Video Test Equipment Signal Paths

The MC14577CP can be evaluated for small legacy test-equipment signal paths that need two low-frequency analog video channels and can operate from the device’s documented supply range. Because the package is a through-hole DIP, it is convenient for prototype boards and repairable instrumentation. Designers should verify bandwidth, gain range, output swing, and loading against the test standard, then establish calibration and termination values before using the circuit for precision measurement.

🌐

Video Distribution Front Ends

The MC14577CP is relevant to simple two-channel video distribution front ends in legacy equipment, particularly where the downstream circuits require active buffering rather than passive fan-out. Its two channels can provide separate amplification paths for related signals, while external resistors define the operating gain and loading. The implementation must respect the amplifier’s input and output impedance, supply requirements, and stability conditions, with particular attention to cable capacitance and termination resistance.

🏭

Retrofit and Maintenance Platforms

The MC14577CP supports maintenance platforms that need to reproduce an obsolete video-amplifier board rather than redesign the entire product. Its 8-PDIP package can simplify mechanical compatibility with existing boards and hand-repair workflows. For a dependable restoration, use the original schematic, compare the device’s electrical limits with observed operating voltages, and test each channel independently under no-load, nominal-load, and maximum intended video-signal conditions.

ملخص المنتجات الموصى بها

MC14577CP Motorola يُستخدم في: Legacy Television Video Signal Conditioning, CRT Monitor Video Amplification, Analog Video Interface Repair, Video Test Equipment Signal Paths, Video Distribution Front Ends, Retrofit and Maintenance Platforms EL4457C Candidate DIP-8 video amplifier substitute يُستخدم في: Legacy Television Video Signal Conditioning, Analog Video Interface Repair, Retrofit and Maintenance Platforms
What is the Motorola MC14577CP?
The Motorola MC14577CP is a dual video amplifier integrated circuit in an 8-PDIP package. Distributor listings identify the part as an amplifier with two video channels, making it suitable for legacy analog video equipment that uses a leaded through-hole package. For a new design, confirm the supply voltage, bandwidth, gain, input and output impedance, and output-drive requirements against the manufacturer datasheet before assigning the device.
What package does the MC14577CP use?
The MC14577CP uses an 8-PDIP, or 8-pin plastic dual in-line package. The product is intended for through-hole PCB assembly rather than surface-mount reflow. Its package outline and lead spacing must match the original board footprint. Use the package drawing and pin-description table in the manufacturer datasheet when assigning signals, because the package drawing alone does not identify the functional purpose of every lead.
How many video channels does the MC14577CP provide?
The MC14577CP provides two video amplifier channels. A dual-channel arrangement can simplify a board containing two related analog video paths by reducing the number of amplifier packages and supporting matched component choices for each channel. The two channels are not necessarily identical in every system, so the signal source, termination, gain network, load, and isolation requirements should be checked separately for each channel.
Is MC14577CP still suitable for legacy television and monitor repair?
The MC14577CP is relevant to legacy television, monitor, and analog video equipment because it is an older dual video amplifier offered in an 8-PDIP package. Suitability depends on matching the original device’s pinout and electrical behavior. Check supply voltage, gain configuration, signal coupling, output loading, and package orientation. The 8-PDIP format is particularly useful when an existing through-hole board must be serviced without redesign.
What are the key specifications of MC14577CP that engineers should know?
The MC14577CP is a dual video amplifier IC in an 8-PDIP through-hole package. Its confirmed catalog characteristics include two video channels, while detailed electrical limits such as supply voltage, bandwidth, gain, slew rate, input impedance, output impedance, and distortion require confirmation from the manufacturer datasheet. These parameters determine whether the amplifier can preserve the required video amplitude and impedance without overloading the following stage.
Where can I download the MC14577CP datasheet PDF?
The MC14577CP datasheet PDF is available through the LCSC datasheet page for C3824422 at https://www.lcsc.com/datasheet/C3824422.pdf. Use the manufacturer document for definitive pin assignments, absolute maximum ratings, recommended operating conditions, electrical characteristics, and application guidance. When consulting an archived document, verify that its revision matches the MC14577CP variant rather than a related package suffix.
Where can I find the MC14577CP pinout?
The MC14577CP pinout is identified in the pin-description table and package drawing of the manufacturer datasheet. The verified catalog listing confirms an 8-PDIP package but does not publish a complete lead-by-lead signal list. Do not infer pin functions from package position alone. Cross-check pin 1 orientation, supply pins, input pins, output pins, and any compensation or feedback connections before soldering the device.
Can EL4457C replace the MC14577CP?
The EL4457C is a candidate legacy dual video-amplifier replacement, but its suitability must be confirmed against the MC14577CP pinout and application circuit. Cross-reference information describes it as a dual, high-speed video op-amp with similar bandwidth and push-pull output in a DIP-8 package. Because package type alone does not guarantee pin compatibility, compare every pin, supply voltage, gain network, stability requirement, and output-loading condition before approving the substitution.
What is the best drop-in replacement for MC14577CP?
The MC14577CP has limited publicly documented drop-in alternatives, so there is no single replacement that can be approved without reviewing the original circuit. EL4457C is the closest documented candidate because it is a dual video amplifier in a DIP-8 package, while MC14577CG is not a footprint drop-in because it uses an SOIC-8 surface-mount package. Use the manufacturer datasheets to verify pin function, supply range, bandwidth, gain, and output drive before substitution.
What can replace an MC14577CP?
EL4457C can be evaluated as a potential MC14577CP replacement, subject to a full electrical and pin-function comparison. Both are described as dual video amplifiers in an 8-pin through-hole package. A replacement should be accepted only when its supply voltage, gain behavior, input and output impedance, bandwidth, slew rate, output drive, stability, and pin assignments match the original design’s requirements. MC14577CG requires a different surface-mount footprint and is not a PCB drop-in replacement.
When should I choose MC14577CP over an alternative?
Choose the MC14577CP when maintaining an existing 8-PDIP video circuit and preserving the original manufacturer-specified device behavior is more important than redesigning the board around a newer amplifier. It is also appropriate when the original schematic requires the confirmed dual-channel architecture and the system’s electrical conditions match the datasheet. For new designs with tighter area, bandwidth, or sourcing requirements, a current amplifier may offer a better platform.
Is MC14577CP suitable for video signal conditioning?
The MC14577CP is suitable for legacy video signal-conditioning applications when its datasheet ratings satisfy the source amplitude, termination, channel bandwidth, output load, and supply requirements. Its two video channels are useful for paired video paths, but video operation also depends on external gain, compensation, and feedback components. Evaluate those values together with the device’s minimum stable gain and output-drive capability before finalizing the circuit.
Where to buy MC14577CP online?
Use the Request a Quote form on this page to request MC14577CP availability, lead time, and ordering details for the 8-PDIP package. The component is listed under the exact manufacturer part number MC14577CP, so a replacement suffix should not be substituted without engineering review. Confirm the package, pinout, operating-temperature requirements, and whether an obsolete marking or original manufacturer material is required before placing the order.
What is the price of MC14577CP?
Current commercial pricing for MC14577CP is best obtained through the Request a Quote form on this page because prices and stock can change with package, quantity, condition, and sourcing channel. The available catalog snippet shows a starting-price reference rather than a complete quantity-break table, so it should not be treated as a firm quotation. Submit the required quantity and package details for an actionable response.
What is the lead time for MC14577CP?
The current lead time for MC14577CP should be requested through the Request a Quote form on this page using the required quantity and 8-PDIP package designation. Lead time can vary with inventory, original-manufacturer material, and inspection requirements. If continuity matters, provide the target date and approved alternate list to the sourcing team so any proposed substitution can be screened for pin and electrical compatibility.

بيانات مرجعية هندسية لـ MC14577CP — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the MC14577CP when repairing or replicating a legacy video circuit whose original design specifies Motorola’s 8-PDIP dual video amplifier. It is the safest choice when preserving the known manufacturer, package, and original schematic behavior is more important than redesigning around a newer amplifier. Evaluate EL4457C when an alternative DIP-8 dual video amplifier is needed, but approve it only after comparing pin assignments, supply range, gain range, bandwidth, slew rate, input and output impedance, output-drive capability, and stability with the original circuit. MC14577CG is functionally related but uses an SOIC-8 footprint, so it requires PCB modification rather than drop-in replacement. For new products, consider a current video amplifier with documented lifecycle status, tighter parameter control, and a package that matches the intended assembly process.

المقارنة مع البدائل

المعامل هذا المنتج EL4457C
Brand Motorola Renesas Electronics
Package 8-PDIP DIP-8
Product Type Video amplifier Dual video op-amp
Channel Count 2 video channels Dual
Mounting Style Through-hole Through-hole

أبرز الفروقات

  • Exact legacy-system compatibility (مقابلEL4457C)
  • Confirmed through-hole package format (مقابلMC14577CG)
  • Dual video-channel architecture (مقابلMC14577CG)

ملاحظات التصميم

Do not treat an 8-pin DIP package as proof of pin compatibility. Before fitting EL4457C or any other substitute, compare every lead function, supply pin, input, output, feedback connection, and compensation requirement against the original schematic and both manufacturers’ datasheets. Package drawing, pin count, and amplifier category are insufficient to establish drop-in equivalence.

Follow the datasheet’s grounding and decoupling arrangement when rebuilding the video path. Place input and output return paths away from high-current switching nodes, use a low-impedance ground reference, and route the two channels to avoid unintended crosstalk. Because the MC14577CP is commonly used with passive feedback networks, preserve short feedback paths and verify board cleanliness because leakage can alter video signal quality.

Validate each channel with the intended source impedance, cable load, termination, and video frequency range. Measure gain, output amplitude, phase response, and channel separation at the actual operating point rather than relying only on nominal schematic values. The original circuit’s resistors and capacitors form part of the amplifier’s stability and bandwidth behavior, so changing them without recalculation can produce oscillation, ringing, or excessive gain.

Confirm the device’s permitted supply voltage and output swing before energizing a restored board. Measure the supply at the IC rather than assuming the nominal rail is present at every point in the circuit. Use adequate local decoupling and check for abnormal current draw, which can indicate incorrect pin orientation, a wrong substitute, damaged signal-path components, or a shorted external network.

For through-hole implementations, follow the datasheet’s recommended lead and board thermal conditions. Estimated thermal performance depends on the actual supply voltage, output swing, load current, copper area, ambient temperature, and heat-sinking arrangement, so no universal dissipation value should be assumed. If either channel operates continuously near its output limit, calculate junction temperature from the applicable datasheet parameters and the board’s measured thermal impedance.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was stated for MC14577CP. The component is a legacy-era 8-PDIP video amplifier and is not presented as an automotive-qualified AEC-Q100 device.

تم التحقق من البيانات في: 2026-11-11 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MC14577CP datasheet MC14577CP specifications MC14577CP pinout MC14577CP datasheet pdf Motorola MC14577CP MC14577CP DIP-8 MC14577CP dual video amplifier MC14577CP replacement MC14577CP equivalent MC14577CP vs EL4457C MC14577CP schematic MC14577CP price MC14577CP stock where to buy MC14577CP

المكونات والمصطلحات ذات الصلة

Motorola MC14577CP EL4457C MC14577CG dual video amplifier video amplifier IC amplifier IC analog amplifier semiconductor 8-PDIP DIP-8 SOIC-8 surface mount through-hole package video signal conditioning legacy television CRT monitor video distribution gain bandwidth product input impedance output impedance slew rate push-pull output composite video
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر