MC14577CP - Dual Video Amplifier | Motorola | DIP-8
부품 번호: MC14577CP ✗ 단종MC14577CP 개요
A video amplifier is an analog integrated circuit used to condition composite, differential, or other video signals before they reach a display, monitor, video processing block, or transmission circuit. In the broader electronics hierarchy, the MC14577CP belongs to the class of amplifier ICs, specifically video amplifiers and modules, rather than being a discrete transistor or a general-purpose digital interface IC. Its dual-channel architecture can reduce the number of separate amplifier packages required in equipment that carries two related video signals.
The MC14577CP is associated with the Motorola MC14577 video-amplifier family and is commonly encountered in legacy television, monitor, video-peripheral, and service-equipment designs. The 8-PDIP format makes the device convenient for through-hole prototypes, repair work, and equipment where a leaded package is preferred over a surface-mount package. The “CP” suffix identifies this particular ordering variant and should be retained when comparing it with other family members.
Because the device is an older video amplifier, design work should begin with the manufacturer datasheet and the system’s signal levels, impedance requirements, bandwidth expectations, supply arrangement, and allowable distortion. The MC14577CP may be especially relevant when maintaining or reproducing older analog video hardware rather than designing a new compact surface-mount product. The key engineering question is whether the original board requires the MC14577CP’s channel count, gain behavior, supply voltage, input/output impedance, and output-drive capability.
In a typical video path, the MC14577CP would sit between a video source and downstream circuitry, with external resistors and capacitors setting gain, bandwidth, coupling, or compensation as required by the application. Its through-hole package supports straightforward prototyping, but designers should still observe the datasheet’s decoupling and grounding recommendations to avoid instability, excessive noise, or channel-to-channel interaction.
This product summary combines package and category information with practical replacement guidance. Because equivalent availability is limited, engineers should verify the pinout, electrical limits, and signal-chain requirements directly against the MC14577CP datasheet before substituting any part. For current commercial availability, use the Request a Quote form on this page rather than relying on historical distributor pricing.
드롭인 대체품: MC14577CP — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
EL4457C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC14577CP 최대 정격 & 전기적 특성
| Product Type | Video amplifier IC |
| Number of Video Channels | 2 |
| 패키지 | 8-PDIP |
| 실장 유형 | Through-hole |
| Manufacturer | Motorola |
| RoHS 상태 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Lead-Free Status | unknown |
MC14577CP 8-pdip 핀 구성 가이드
MC14577CP(8-pdip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: MC14577CP.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC14577CP 적합 용도: 6 애플리케이션s: Legacy Television Video Signal Conditioning, CRT Monitor Video Amplification, Analog Video Interface Repair, Video Test Equipment Signal Paths, Video Distribution Front Ends, Retrofit and Maintenance Platforms.
Legacy Television Video Signal Conditioning
The MC14577CP fits legacy television service work when the original board uses a dual video amplifier in an 8-PDIP package. Its two channels can condition related video paths while preserving the established through-hole construction and component arrangement. The designer should reproduce the original feedback and compensation values, confirm the amplifier’s allowed operating region, and account for any signal attenuation or gain differences introduced by the surrounding source, load, and coupling networks.
추천
CRT Monitor Video Amplification
The MC14577CP is applicable to legacy CRT monitor circuitry where separate video channels drive downstream display stages through passive networks. The 8-PDIP format simplifies repairs on existing through-hole boards, while the dual-channel architecture can support paired luminance and chrominance paths when the original design uses them in that manner. Exact channel assignment and signal conditioning must follow the original schematic and the MC14577CP pinout, because the package confirms pin count but not individual lead functions.
추천
Analog Video Interface Repair
The MC14577CP is useful in repair and modernization projects that retain an analog video interface but need to replace a failed dual amplifier in the original 8-PDIP footprint. Its suitability depends on reproducing the original gain distribution and checking the amplifier’s input and output impedances against the connected source and load. A replacement decision should compare not only the package, but also DC operating points, signal swing, bandwidth, output-drive capability, and stability with the actual external component values.
추천
Video Test Equipment Signal Paths
The MC14577CP can be evaluated for small legacy test-equipment signal paths that need two low-frequency analog video channels and can operate from the device’s documented supply range. Because the package is a through-hole DIP, it is convenient for prototype boards and repairable instrumentation. Designers should verify bandwidth, gain range, output swing, and loading against the test standard, then establish calibration and termination values before using the circuit for precision measurement.
추천
Video Distribution Front Ends
The MC14577CP is relevant to simple two-channel video distribution front ends in legacy equipment, particularly where the downstream circuits require active buffering rather than passive fan-out. Its two channels can provide separate amplification paths for related signals, while external resistors define the operating gain and loading. The implementation must respect the amplifier’s input and output impedance, supply requirements, and stability conditions, with particular attention to cable capacitance and termination resistance.
추천
Retrofit and Maintenance Platforms
The MC14577CP supports maintenance platforms that need to reproduce an obsolete video-amplifier board rather than redesign the entire product. Its 8-PDIP package can simplify mechanical compatibility with existing boards and hand-repair workflows. For a dependable restoration, use the original schematic, compare the device’s electrical limits with observed operating voltages, and test each channel independently under no-load, nominal-load, and maximum intended video-signal conditions.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC14577CP — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EL4457C |
|---|---|---|
| Brand | Motorola | Renesas Electronics |
| Package | 8-PDIP | DIP-8 |
| Product Type | Video amplifier | Dual video op-amp |
| Channel Count | 2 video channels | Dual |
| Mounting Style | Through-hole | Through-hole |
주요 차별점
- Exact legacy-system compatibility (vs EL4457C)
- Confirmed through-hole package format (vs MC14577CG)
- Dual video-channel architecture (vs MC14577CG)
설계 노트
Do not treat an 8-pin DIP package as proof of pin compatibility. Before fitting EL4457C or any other substitute, compare every lead function, supply pin, input, output, feedback connection, and compensation requirement against the original schematic and both manufacturers’ datasheets. Package drawing, pin count, and amplifier category are insufficient to establish drop-in equivalence.
Follow the datasheet’s grounding and decoupling arrangement when rebuilding the video path. Place input and output return paths away from high-current switching nodes, use a low-impedance ground reference, and route the two channels to avoid unintended crosstalk. Because the MC14577CP is commonly used with passive feedback networks, preserve short feedback paths and verify board cleanliness because leakage can alter video signal quality.
Validate each channel with the intended source impedance, cable load, termination, and video frequency range. Measure gain, output amplitude, phase response, and channel separation at the actual operating point rather than relying only on nominal schematic values. The original circuit’s resistors and capacitors form part of the amplifier’s stability and bandwidth behavior, so changing them without recalculation can produce oscillation, ringing, or excessive gain.
Confirm the device’s permitted supply voltage and output swing before energizing a restored board. Measure the supply at the IC rather than assuming the nominal rail is present at every point in the circuit. Use adequate local decoupling and check for abnormal current draw, which can indicate incorrect pin orientation, a wrong substitute, damaged signal-path components, or a shorted external network.
For through-hole implementations, follow the datasheet’s recommended lead and board thermal conditions. Estimated thermal performance depends on the actual supply voltage, output swing, load current, copper area, ambient temperature, and heat-sinking arrangement, so no universal dissipation value should be assumed. If either channel operates continuously near its output limit, calculate junction temperature from the applicable datasheet parameters and the board’s measured thermal impedance.
규정 준수 정보
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was stated for MC14577CP. The component is a legacy-era 8-PDIP video amplifier and is not presented as an automotive-qualified AEC-Q100 device.