onsemi

MC33171PG - 1.8 MHz Low-Power Op Amp | onsemi | 8-DIP

MPN: MC33171PG ✗ انتهى عمره الإنتاجي
3.0 V to 44 V Vdss 180 uA Id 8-PDIP (0.300 inch, 7.62 mm) Package
الحد الأدنى للطلب: 1 |

MC33171PG نظرة عامة

The onsemi MC33171PG is a single general-purpose operational amplifier in an 8-pin plastic DIP package, specified for single-supply operation from 3.0 V to 44 V. It combines a 1.8 MHz gain-bandwidth product with a 2.1 V/us slew rate and a low quiescent current of 180 uA per amplifier. The device is designed for low-power instrumentation, industrial signal conditioning, sensor amplification, and control applications requiring operation from a single supply.

An operational amplifier, or op amp, is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Its hierarchy extends from general-purpose amplification to signal conditioning, analog mixed-signal ICs, and broader power-management-aware system design. The MC33171/72/74 family uses bipolar fabrication without JFET input transistors, combining low supply current with adequate bandwidth and slew rate for many industrial signal paths.

Key electrical characteristics include a 1.8 MHz gain-bandwidth product, 2.1 V/us slew rate, and approximately 180 uA operating current per amplifier. The wide 3.0 V to 44 V single-supply range allows operation from conventional 5 V, 12 V, 24 V, and higher industrial rails. The MC33171PG is specified across a -40C to +85C temperature range, while its input bias current is listed at 20 nA and input offset voltage at 2 mV.

The MC33171 series is particularly suited to single-supply operation but can also be used with split supplies when the circuit and common-mode conditions permit. Its bipolar input stage avoids the need for JFET technology, and the 1.8 MHz bandwidth supports audio-frequency and general instrumentation tasks. The 2.1 V/us slew rate improves large-signal response compared with strictly low-bandwidth precision amplifiers, although the device remains a general-purpose rather than a high-speed amplifier.

Typical applications include low-frequency sensor conditioning, transducer amplification, process-control loops, industrial current or voltage monitoring, audio preamplification, and general-purpose analog filtering. For higher-impedance sensors, the 20 nA input bias specification helps minimize loading, while the 2 mV input offset must be considered in precision measurement paths. Feedback-network layout, grounding, and supply bypassing remain important at the board level.

When designing around the MC33171PG, check input and output voltage swing at the intended load because single-supply operation restricts the usable signal range near the rails. Place bypass capacitors close to the supply pins, route feedback paths away from high-current inputs, and verify stability with the selected gain, load capacitance, and compensation network. For an obsolete legacy design, confirm availability before committing to new production layouts.

This page combines lifecycle status, package details, verified electrical characteristics, replacement guidance, and board-level design notes for engineers maintaining MC33171PG-based instrumentation. It also compares same-footprint amplifier options and highlights the trade-offs among supply current, bandwidth, input offset, and operating-temperature range.

بدائل مباشرة لـ MC33171PG — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع MC33171PG (نفس عامل الشكل والبصمة) — يختلف في Amplifier Type, Mounting Style, Number of Circuits, Package.

onsemi
Amplifier Type: Single general-purpose operational amplifier
Mounting Style: Through-hole
Number of Circuits: 1 circuit
قارن مع MC33171PG →

MC33171P

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
onsemi
📦 8-PDIP (0.300 inch, 7.62 mm)
Single general-purpose operational amplifier · 1 circuit · 3.0 V to 44 V · 180 uA per amplifier · 1.8 MHz · 2.1 V/us · Bipolar · Single supply or split supply

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM392P

✅ بديل مباشر
📦 8-DIP
Same 8-DIP single-amplifier footprint, but a different low-power amplifier family with different offset, bias-current, bandwidth, and stability characteristics; overall parameter match 70%

📋 بديل مرجعي (غير موجود في الكتالوج)

UA741

✅ بديل مباشر
📦 8-DIP
Functional equivalent in the 8-DIP standard op-amp format, but input offset, bias current, gain-bandwidth product, slew rate, and output-swing performance differ; overall parameter match 70%

📋 بديل مرجعي (غير موجود في الكتالوج)

MC33171PG الحدود القصوى والخصائص الكهربائية

Amplifier Type General Purpose
Number of Circuits 1 amplifier
Supply Voltage Range 3.0 V to 44 V
Gain-Bandwidth Product 1.8 MHz
Slew Rate 2.1 V/us
Supply Current per Amplifier 180 uA
Input Bias Current 20 nA
Input Offset Voltage 2 mV
نطاق درجة حرارة التشغيل -40C to +85C
العلبة 8-PDIP (0.300 inch, 7.62 mm)
نمط التركيب Through Hole
Packaging Tube
Input Transistor Technology Bipolar
Operating Mode Single Supply
Product Status Obsolete
Family MC33171

تكوين أطراف MC33171PG

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
دبوس 1 NC — Not connected
دبوس 2 IN- — Inverting input
دبوس 3 IN+ — Non-inverting input
دبوس 4 V- — Negative supply or ground connection
دبوس 5 NC — Not connected
دبوس 6 OUT — Analog output
دبوس 7 V+ — Positive supply input
دبوس 8 NC — Not connected

التطبيقات النموذجية

MC33171PG مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Process Control Loop Amplification, 24 V Industrial Power Rail Monitoring, Low-Frequency Audio Preamplification, Current and Voltage Measurement Front Ends, Legacy Instrumentation Retrofit.

🏭

Industrial Sensor Signal Conditioning

The MC33171PG fits low-frequency industrial sensor conditioning because its 1.8 MHz gain-bandwidth product and 2.1 V/us slew rate provide adequate closed-loop response for many transducer signals. Its approximately 180 uA supply current per amplifier also limits the burden on low-power sensing nodes. Place the amplifier in a non-inverting configuration when the sensor output is referenced to ground, and keep the feedback resistors close to the device. Because the input offset is 2 mV and bias current is 20 nA, verify that the source impedance and required measurement resolution tolerate those errors.

⚙️

Process Control Loop Amplification

The MC33171PG can serve as the error amplifier in a basic process-control loop running from a single 3.0 V to 44 V supply. Its 2.1 V/us slew rate allows the output to respond to control corrections faster than very low-bandwidth precision amplifiers, while the 1.8 MHz gain-bandwidth product supports useful closed-loop bandwidth at moderate gains. Keep compensation components close to the amplifier and avoid placing high-current actuator wiring beside the feedback trace. Verify output swing against the actuator range and confirm stability with the actual load and compensation network.

🔋

24 V Industrial Power Rail Monitoring

A divide-and-amplify stage built with the MC33171PG is suitable for monitoring a fraction of a 24 V industrial rail. The device accepts a single supply up to 44 V, so the resistor divider can reference the rail directly while the amplifier operates from the same supply. Its 1.8 MHz gain-bandwidth product is ample for relatively slow rail measurements, and the 180 uA supply current is modest for continuous monitoring. Use a protected divider, account for the 2 mV input offset, and ensure the output does not exceed the downstream ADC input range.

🎧

Low-Frequency Audio Preamplification

The MC33171PG provides sufficient gain-bandwidth product and slew rate for low-frequency audio preamplification, including microphone-level or line-level signal conditioning. The 1.8 MHz bandwidth comfortably covers audio-band applications, while 180 uA operating current per amplifier supports low-power designs. The 20 nA input bias current is acceptable for typical audio source impedances, although the 2 mV offset may be audible in high-gain stages. Use stable feedback values, keep input capacitance low, and test the completed layout for oscillation or excessive peaking.

📟

Current and Voltage Measurement Front Ends

The MC33171PG works as the gain stage in a scaled current- or voltage-measurement front end when the sensed level can be accommodated within its input common-mode range. Its 20 nA input bias current limits the error introduced by very high source impedances, while the 2.1 V/us slew rate supports faster measurement transients than a precision-only amplifier. Gain error and offset should be calibrated after installation if measurement accuracy matters. Use matched resistor networks and provide input clamping so transients do not exceed the amplifier's absolute maximum ratings.

🔧

Legacy Instrumentation Retrofit

The MC33171PG is appropriate for maintaining or repairing an existing 8-DIP instrument in which the original footprint, supply rails, and feedback topology are already established. The same-family MC33171P offers the closest starting point for evaluation, and the LM392P is a documented 8-DIP comparison part. Replacement is not automatic: compare offset voltage, input bias current, gain-bandwidth product, slew rate, common-mode range, output swing, noise, and stability with the original design. Preserve the obsolete part's pinout only after the alternative passes these checks.

ملخص المنتجات الموصى بها

MC33171P onsemi يُستخدم في: Industrial Sensor Signal Conditioning, Process Control Loop Amplification, 24 V Industrial Power Rail Monitoring, Low-Frequency Audio Preamplification, Current and Voltage Measurement Front Ends, Legacy Instrumentation Retrofit LM392P Low-power single 8-DIP amplifier alternative يُستخدم في: Industrial Sensor Signal Conditioning, Process Control Loop Amplification, 24 V Industrial Power Rail Monitoring, Legacy Instrumentation Retrofit UA741 Functional equivalent single operational amplifier يُستخدم في: Low-Frequency Audio Preamplification TL081 Functional equivalent general-purpose amplifier يُستخدم في: Current and Voltage Measurement Front Ends
What is the MC33171PG?
The MC33171PG is a single, general-purpose bipolar operational amplifier from onsemi in an 8-pin plastic DIP package. According to the onsemi MC33171 family documentation, it operates from a single supply of 3.0 V to 44 V, provides 1.8 MHz of gain-bandwidth product, and offers a 2.1 V/us slew rate. The part is suitable for industrial instrumentation, sensor conditioning, control loops, and low-frequency audio amplification.
What is the operating voltage range of MC33171PG?
The MC33171PG operates from 3.0 V to 44 V on a single supply. The onsemi MC33171 family documentation identifies the MC33171/72/74 devices as low-power single-supply operational amplifiers for this range. That voltage span supports conventional 5 V, 12 V, and 24 V systems, although engineers must still confirm the input common-mode range and output swing at the selected supply voltage.
What are the key specifications of MC33171PG that engineers should know?
The MC33171PG combines a 1.8 MHz gain-bandwidth product, 2.1 V/us slew rate, and approximately 180 uA of supply current per amplifier. The onsemi family documentation also identifies 20 nA input bias current, 2 mV input offset voltage, and operation from 3.0 V to 44 V. These figures position the device as a low-power, general-purpose amplifier for industrial signal conditioning rather than a precision or high-speed amplifier.
Is the MC33171PG an obsolete part?
Yes, the MC33171PG is identified as an obsolete or end-of-life device in distributor lifecycle records. The onsemi MC33171 family page still describes the device family, but the PG ordering code should be treated as a legacy component rather than a new-design choice. Request current availability through the Request a Quote form on this page, and prefer a supported family member for new production.
Where can I download the MC33171PG datasheet PDF?
The MC33171PG datasheet is available through the onsemi MC33171 family product page and through the datasheet mirrors listed in the technical references on this page. Use the manufacturer document for authoritative pin assignments, recommended operating conditions, electrical characteristics, and application information. The MC33171 family document covers the MC33171, MC33172, and MC33174 amplifiers.
Where can I find the MC33171PG pinout?
The MC33171PG uses a standard single-amplifier 8-pin DIP arrangement with the non-inverting input at pin 3, the inverting input at pin 2, the output at pin 6, the negative supply at pin 4, and the positive supply at pin 7. Use the pin-description table in the onsemi datasheet when assigning PCB tracks. Pins 1, 5, and 8 are not connected.
What is the MC33171PG vs LM392P comparison?
The MC33171PG and LM392P are both low-power single-amplifier devices offered in an 8-DIP configuration, but their electrical characteristics are not identical. The MC33171PG is specified at 1.8 MHz gain-bandwidth product, 2.1 V/us slew rate, and 180 uA supply current per amplifier. Confirm offset, bias current, output swing, and stability requirements before using the LM392P as a substitution.
What is the difference between MC33171PG and MC33171P?
The MC33171PG and MC33171P belong to the same onsemi MC33171 single-amplifier family and use the same 8-pin through-hole package. Their principal documented distinction is the temperature grade: MC33171PG is specified from -40C to +85C, while the comparison records identify MC33171P with a lower maximum temperature of 85C for the standard industrial grade. Verify the exact suffix specifications before substitution.
When should I choose MC33171PG over a lower-power precision amplifier?
Choose the MC33171PG when the circuit needs more than unity-gain stability and modest frequency response: it provides 1.8 MHz of gain-bandwidth product and a 2.1 V/us slew rate. A lower-power precision amplifier may offer lower offset and bias current, but the MC33171PG provides a simpler general-purpose solution for audio-frequency industrial signals, provided its obsolete lifecycle status is acceptable.
Can MC33171PG replace a UA741 in an existing circuit?
The MC33171PG can be considered for a legacy UA741 circuit only after checking the actual pinout, supply voltage, input common-mode range, output swing, noise, offset, stability, and load requirements. The MC33171 family documentation identifies the UA741 among common functional equivalents, but functional equivalence does not guarantee identical AC, DC, or stability behavior in every feedback configuration.
What is the best drop-in replacement for MC33171PG?
The closest documented same-family drop-in candidate is the onsemi MC33171P, which uses the same 8-DIP footprint and belongs to the same MC33171 electrical series. The LM392P is another 8-DIP single-op-amp alternative identified in comparison records, but it is not part of the MC33171 series. Confirm the temperature grade, offset voltage, bias current, common-mode behavior, and AC stability before choosing either.
Is the MC33171PG suitable for 24 V industrial control applications?
Yes, the MC33171PG's 3.0 V to 44 V single-supply capability is appropriate for many 24 V industrial control circuits. Its 1.8 MHz gain-bandwidth product is sufficient for many low-frequency sensing and conditioning tasks, and its -40C to +85C rating suits industrial environments. Use transient protection and verify the input and output voltage limits at the actual supply tolerance.
What can replace MC33171PG in a legacy design?
The onsemi MC33171P is the most direct replacement to evaluate because it is from the same amplifier family and retains the 8-DIP through-hole format. The LM392P is a second 8-DIP option, while UA741, CA3140, and TL081 are listed as functional equivalents in component-reference material. Only the MC33171P carries the same-family qualification; the other options require a complete electrical and stability review.
How should the MC33171PG be bypassed on a PCB?
Place the supply bypass capacitor as close as practical to the positive supply pin at pin 7, with a solid ground return to pin 4. Keep feedback and input traces short and route them away from switching nodes and other high-current paths. Because the device is obsolete, preserve the original footprint and pin assignments unless an alternative has been fully validated electrically and thermally.
Where can I buy MC33171PG and what is its current lead time?
The MC33171PG is an obsolete onsemi part, so current supply and lead time depend on remaining factory and channel inventory. Use the Request a Quote form on this page to request current availability, quantity breaks, and a lead-time commitment. For new designs, request a supported onsemi family member instead of building a dependency on a legacy single-supply amplifier.

بيانات مرجعية هندسية لـ MC33171PG — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the MC33171PG for an existing industrial design that specifically requires its 8-PDIP footprint, 3.0 V to 44 V single-supply capability, 1.8 MHz gain-bandwidth product, and 2.1 V/us slew rate. For a maintenance replacement, evaluate the onsemi MC33171P first because it belongs to the same family and preserves the principal frequency and slew-rate characteristics. Consider the LM392P only after verifying its offset, bias current, common-mode range, output swing, and stability in the original circuit. UA741-class devices may satisfy functional needs, but they are not automatic drop-ins because offset, bias, bandwidth, noise, and compensation requirements can differ. For new designs, avoid building around an obsolete ordering code unless supply continuity has been confirmed and the board is expected to remain in service for many years.

المقارنة مع البدائل

المعامل هذا المنتج MC33171P LM392P UA741
Package 8-PDIP (0.300 inch, 7.62 mm) 8-PDIP - same footprint 8-DIP - same footprint 8-DIP - same footprint
Brand onsemi onsemi Texas Instruments Texas Instruments
Amplifier Count 1 1 1 1

أبرز الفروقات

  • Same-family replacement path with minimal functional-learning effort (مقابلMC33171P)
  • Wide single-supply operating range (مقابلLM392P)
  • Defined low-power AC performance (مقابلUA741)

ملاحظات التصميم

Confirm the full supply range, common-mode limits, and output swing against the actual circuit voltage. A 44 V maximum supply rating does not permit every input or output to reach either rail. Place a local bypass capacitor close to pin 7 and provide a short, low-impedance ground return to pin 4. Decouple any noisy 24 V rail upstream so switching transients do not appear directly at the amplifier inputs.

Preserve the original 8-DIP footprint when maintaining an existing board and keep the feedback resistors close to pins 2, 3, and 6. Route the non-inverting input away from power-switching nodes and high-current return paths. A solid ground plane is preferable to a fragmented ground connection, particularly because an obsolete legacy layout may have been designed before current EMC practices were applied.

Do not substitute the amplifier solely because the package has eight pins. Compare input bias current, input offset voltage, gain-bandwidth product, slew rate, common-mode range, output swing, noise, and stability with the original design. Pay particular attention to gain and capacitive-load stability because a different amplifier family can oscillate with feedback values that worked reliably in the MC33171PG circuit.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The onsemi family page states that MC33171-series devices are specified over industrial and automotive temperature ranges, but it does not establish the compliance status of the obsolete MC33171PG ordering code. Verify the original package markings and obtain the applicable onsemi material declarations before reuse in new regulated equipment.

تم التحقق من البيانات في: 2026-11-16 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MC33171PG datasheet MC33171PG datasheet pdf MC33171PG pinout onsemi MC33171PG MC33171PG equivalent MC33171PG replacement MC33171PG cross reference MC33171PG vs LM392P MC33171PG vs MC33171P MC33171 8-DIP op amp MC33171PG 1.8 MHz amplifier MC33171PG 24 V industrial MC33171PG obsolete MC33171PG buy

المكونات والمصطلحات ذات الصلة

onsemi MC33171PG MC33171P MC33171 LM392P UA741 CA3140 TL081 operational amplifier op amp general-purpose amplifier analog signal conditioning single-supply operation bipolar fabrication gain-bandwidth product slew rate input bias current input offset voltage common-mode voltage range 8-PDIP package DIP package through-hole mounting industrial instrumentation process control sensor conditioning
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر