MC33171PG - 1.8 MHz Low-Power Op Amp | onsemi | 8-DIP
MPN: MC33171PG ✗ סוף ייצורMC33171PG סקירה
An operational amplifier, or op amp, is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Its hierarchy extends from general-purpose amplification to signal conditioning, analog mixed-signal ICs, and broader power-management-aware system design. The MC33171/72/74 family uses bipolar fabrication without JFET input transistors, combining low supply current with adequate bandwidth and slew rate for many industrial signal paths.
Key electrical characteristics include a 1.8 MHz gain-bandwidth product, 2.1 V/us slew rate, and approximately 180 uA operating current per amplifier. The wide 3.0 V to 44 V single-supply range allows operation from conventional 5 V, 12 V, 24 V, and higher industrial rails. The MC33171PG is specified across a -40C to +85C temperature range, while its input bias current is listed at 20 nA and input offset voltage at 2 mV.
The MC33171 series is particularly suited to single-supply operation but can also be used with split supplies when the circuit and common-mode conditions permit. Its bipolar input stage avoids the need for JFET technology, and the 1.8 MHz bandwidth supports audio-frequency and general instrumentation tasks. The 2.1 V/us slew rate improves large-signal response compared with strictly low-bandwidth precision amplifiers, although the device remains a general-purpose rather than a high-speed amplifier.
Typical applications include low-frequency sensor conditioning, transducer amplification, process-control loops, industrial current or voltage monitoring, audio preamplification, and general-purpose analog filtering. For higher-impedance sensors, the 20 nA input bias specification helps minimize loading, while the 2 mV input offset must be considered in precision measurement paths. Feedback-network layout, grounding, and supply bypassing remain important at the board level.
When designing around the MC33171PG, check input and output voltage swing at the intended load because single-supply operation restricts the usable signal range near the rails. Place bypass capacitors close to the supply pins, route feedback paths away from high-current inputs, and verify stability with the selected gain, load capacitance, and compensation network. For an obsolete legacy design, confirm availability before committing to new production layouts.
This page combines lifecycle status, package details, verified electrical characteristics, replacement guidance, and board-level design notes for engineers maintaining MC33171PG-based instrumentation. It also compares same-footprint amplifier options and highlights the trade-offs among supply current, bandwidth, input offset, and operating-temperature range.
חלופות תחליף ישיר עבור MC33171PG — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MC33171PG (אותו גורם צורה וטביעת רגל) — שונים ב Amplifier Type, Mounting Style, Number of Circuits, Package.
MC33171P
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM392P
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
UA741
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MC33171PG דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | General Purpose |
| Number of Circuits | 1 amplifier |
| Supply Voltage Range | 3.0 V to 44 V |
| Gain-Bandwidth Product | 1.8 MHz |
| Slew Rate | 2.1 V/us |
| Supply Current per Amplifier | 180 uA |
| Input Bias Current | 20 nA |
| Input Offset Voltage | 2 mV |
| טווח טמפרטורת פעולה | -40C to +85C |
| מארז | 8-PDIP (0.300 inch, 7.62 mm) |
| סגנון הרכבה | Through Hole |
| Packaging | Tube |
| Input Transistor Technology | Bipolar |
| Operating Mode | Single Supply |
| Product Status | Obsolete |
| Family | MC33171 |
תצורת פינים של MC33171PG
| פין 1 | NC — Not connected |
| פין 2 | IN- — Inverting input |
| פין 3 | IN+ — Non-inverting input |
| פין 4 | V- — Negative supply or ground connection |
| פין 5 | NC — Not connected |
| פין 6 | OUT — Analog output |
| פין 7 | V+ — Positive supply input |
| פין 8 | NC — Not connected |
יישומים טיפוסיים
MC33171PG מתאים עבור 6 יישוםs: Industrial Sensor Signal Conditioning, Process Control Loop Amplification, 24 V Industrial Power Rail Monitoring, Low-Frequency Audio Preamplification, Current and Voltage Measurement Front Ends, Legacy Instrumentation Retrofit.
Industrial Sensor Signal Conditioning
The MC33171PG fits low-frequency industrial sensor conditioning because its 1.8 MHz gain-bandwidth product and 2.1 V/us slew rate provide adequate closed-loop response for many transducer signals. Its approximately 180 uA supply current per amplifier also limits the burden on low-power sensing nodes. Place the amplifier in a non-inverting configuration when the sensor output is referenced to ground, and keep the feedback resistors close to the device. Because the input offset is 2 mV and bias current is 20 nA, verify that the source impedance and required measurement resolution tolerate those errors.
מומלץ
Process Control Loop Amplification
The MC33171PG can serve as the error amplifier in a basic process-control loop running from a single 3.0 V to 44 V supply. Its 2.1 V/us slew rate allows the output to respond to control corrections faster than very low-bandwidth precision amplifiers, while the 1.8 MHz gain-bandwidth product supports useful closed-loop bandwidth at moderate gains. Keep compensation components close to the amplifier and avoid placing high-current actuator wiring beside the feedback trace. Verify output swing against the actuator range and confirm stability with the actual load and compensation network.
מומלץ
24 V Industrial Power Rail Monitoring
A divide-and-amplify stage built with the MC33171PG is suitable for monitoring a fraction of a 24 V industrial rail. The device accepts a single supply up to 44 V, so the resistor divider can reference the rail directly while the amplifier operates from the same supply. Its 1.8 MHz gain-bandwidth product is ample for relatively slow rail measurements, and the 180 uA supply current is modest for continuous monitoring. Use a protected divider, account for the 2 mV input offset, and ensure the output does not exceed the downstream ADC input range.
מומלץ
Low-Frequency Audio Preamplification
The MC33171PG provides sufficient gain-bandwidth product and slew rate for low-frequency audio preamplification, including microphone-level or line-level signal conditioning. The 1.8 MHz bandwidth comfortably covers audio-band applications, while 180 uA operating current per amplifier supports low-power designs. The 20 nA input bias current is acceptable for typical audio source impedances, although the 2 mV offset may be audible in high-gain stages. Use stable feedback values, keep input capacitance low, and test the completed layout for oscillation or excessive peaking.
מומלץ
Current and Voltage Measurement Front Ends
The MC33171PG works as the gain stage in a scaled current- or voltage-measurement front end when the sensed level can be accommodated within its input common-mode range. Its 20 nA input bias current limits the error introduced by very high source impedances, while the 2.1 V/us slew rate supports faster measurement transients than a precision-only amplifier. Gain error and offset should be calibrated after installation if measurement accuracy matters. Use matched resistor networks and provide input clamping so transients do not exceed the amplifier's absolute maximum ratings.
מומלץ
Legacy Instrumentation Retrofit
The MC33171PG is appropriate for maintaining or repairing an existing 8-DIP instrument in which the original footprint, supply rails, and feedback topology are already established. The same-family MC33171P offers the closest starting point for evaluation, and the LM392P is a documented 8-DIP comparison part. Replacement is not automatic: compare offset voltage, input bias current, gain-bandwidth product, slew rate, common-mode range, output swing, noise, and stability with the original design. Preserve the obsolete part's pinout only after the alternative passes these checks.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MC33171PG — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MC33171P | LM392P | UA741 |
|---|---|---|---|---|
| Package | 8-PDIP (0.300 inch, 7.62 mm) | 8-PDIP - same footprint | 8-DIP - same footprint | 8-DIP - same footprint |
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Amplifier Count | 1 | 1 | 1 | 1 |
מבדילים עיקריים
- Same-family replacement path with minimal functional-learning effort (לעומתMC33171P)
- Wide single-supply operating range (לעומתLM392P)
- Defined low-power AC performance (לעומתUA741)
הערות תכנון
Confirm the full supply range, common-mode limits, and output swing against the actual circuit voltage. A 44 V maximum supply rating does not permit every input or output to reach either rail. Place a local bypass capacitor close to pin 7 and provide a short, low-impedance ground return to pin 4. Decouple any noisy 24 V rail upstream so switching transients do not appear directly at the amplifier inputs.
Preserve the original 8-DIP footprint when maintaining an existing board and keep the feedback resistors close to pins 2, 3, and 6. Route the non-inverting input away from power-switching nodes and high-current return paths. A solid ground plane is preferable to a fragmented ground connection, particularly because an obsolete legacy layout may have been designed before current EMC practices were applied.
Do not substitute the amplifier solely because the package has eight pins. Compare input bias current, input offset voltage, gain-bandwidth product, slew rate, common-mode range, output swing, noise, and stability with the original design. Pay particular attention to gain and capacitive-load stability because a different amplifier family can oscillate with feedback values that worked reliably in the MC33171PG circuit.
מידע על תאימות
The onsemi family page states that MC33171-series devices are specified over industrial and automotive temperature ranges, but it does not establish the compliance status of the obsolete MC33171PG ordering code. Verify the original package markings and obtain the applicable onsemi material declarations before reuse in new regulated equipment.