NXP Semiconductors

MC33989DW - Automotive CAN System Basis Chip | NXP

MPN: MC33989DW ✓ نشط
5.5 V to 18 V Vdss 28-SOIC, 0.295 inch by 7.50 mm width Package
الحد الأدنى للطلب: 1 |

MC33989DW نظرة عامة

The NXP Semiconductors MC33989DW is an automotive system basis chip with a high-speed CAN physical interface, integrated into a 28-SOIC package. Its three headline characteristics are a 5.5 V to 18 V supply range, CAN operation up to 1.0 Mbaud, and an SPI interface for connection to a microcontroller. The device also combines two voltage regulators, four high-voltage wake-up inputs, VSUP monitoring, and fault-detection circuitry.

A system basis chip, or SBC, is an interface IC that consolidates functions normally distributed around a microcontroller in an automotive electronic control unit. Its position in the hierarchy is SBC → CAN interface IC → interface IC → semiconductor. Integrating power regulation, bus physical-layer functions, wake-up detection, and supply supervision reduces the component count and board area needed around the host microcontroller while preserving a structured diagnostic and control interface.

The MC33989DW combines a 1.0 Mbaud-capable CAN physical interface with an SPI host interface. Four high-voltage wake-up inputs allow the device to detect external wake events in an automotive environment. Two internal voltage regulators support the host power architecture, while VSUP monitoring and fault-detection circuitry provide supply-state supervision. These functions make the device suitable for compact ECU subsystems that require more than a standalone CAN transceiver.

Automotive electronics commonly separate a low-power communication domain from the main MCU supply domain. MC33989DW supports this architecture by combining a regulated supply path, CAN physical signaling, and wake-up detection in one package. The SPI connection gives the host processor access to control and status functions without requiring a separate external CAN controller. Because the device also performs supply monitoring, designers can base early-startup and fault-handling decisions around a dedicated system basis component.

Typical uses include body and comfort controllers, engine-control subsystems, transmission controllers, sensor nodes, and other automotive modules using CAN communication. It is also relevant to industrial or transportation equipment where a ruggedized supply range, local wake-up detection, and a high-speed CAN physical interface simplify the implementation around a microcontroller.

When laying out the circuit, place the device and its support components according to the pin-description and recommended-layout sections in the NXP manufacturer datasheet. Confirm the complete 28-pin mapping, supply decoupling requirements, CAN transceiver connection details, and external component values before releasing the PCB; the MC33989DW integrates several subsystems whose layout decisions can affect signal integrity and startup behavior.

This page organizes the MC33989DW electrical ratings, package information, practical design guidance, application fit, and verified drop-in replacement status. It also distinguishes a true pin-compatible replacement from a merely similar CAN transceiver so procurement and engineering teams can avoid assuming that a different package or architecture is electrically interchangeable.

بدائل مباشرة لـ MC33989DW — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع MC33989DW (نفس عامل الشكل والبصمة) — يختلف في Package.

NXP Semiconductors
Package: 28-SOIC (DW suffix)
قارن مع MC33989DW →

لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.

اطلب بدائل

MC33989DW المواصفات

Product Type System basis chip with high-speed CAN transceiver
Supply Voltage Range 5.5 V to 18 V
CAN Data Rate 1.0 Mbaud
العلبة 28-SOIC, 0.295 inch by 7.50 mm width
Integrated Voltage Regulators 2
High-Voltage Wake-Up Inputs 4
Host Interface SPI
Supply Monitoring VSUP monitoring
Fault Detection Integrated fault-detection circuitry
Primary Application Automotive electronic control units
CAN Physical Interface 1 integrated high-speed CAN transceiver
نوع التركيب Surface mount

دليل تكوين أطراف MC33989DW 28-soic, 0.295 inch by 7.50 mm width

تكوين الأطراف لـ MC33989DW (حزمة 28-soic, 0.295 inch by 7.50 mm width). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 28-soic, 0.295 inch by 7.50 mm width لـ MC33989DW

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MC33989DW.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

MC33989DW مناسب لـ 6 التطبيقs: Automotive Engine Control Unit, Body Control Module, Transmission Control Electronics, Automotive Sensor Node, Industrial CAN Gateway, Transportation Equipment Controller.

🚗

Automotive Engine Control Unit

The MC33989DW fits an automotive engine-control unit that needs a consolidated interface between its MCU and vehicle networks. Its 1.0 Mbaud CAN physical interface handles the CAN connection, while the SPI interface gives the host processor access to control and status functions. Two integrated voltage regulators and VSUP monitoring support the ECU power architecture. With a 5.5 V to 18 V operating range and four high-voltage wake-up inputs, the device can also support low-power wake behavior. The implementation trade-off is that several subsystems share one package, so pin assignment, transient protection, grounding, and decoupling must follow the manufacturer's application and layout guidance.

🚗

Body Control Module

A body control module can use the MC33989DW to combine CAN communications with local power-management and wake-up functions. The 1.0 Mbaud CAN physical interface serves the vehicle network, while four high-voltage wake-up inputs detect external activity that can transition a parked module into operation. The two internal regulators reduce the number of separate supply components around the MCU, and VSUP monitoring assists the controller in identifying abnormal supply conditions. Because the package is a 28-SOIC, the design must account for the integrated functions when planning board area and protection. The 5.5 V to 18 V range is suitable for many 12 V automotive systems, subject to transient and load-dump requirements specified in the datasheet.

⚙️

Transmission Control Electronics

The MC33989DW is suitable for transmission-control electronics that combine a microcontroller, CAN communications, and supervised power rails. The device's CAN physical interface supports operation up to 1.0 Mbaud, while its SPI connection provides a straightforward host-control path. Integrated voltage regulators can supply compatible MCU domains, and fault-detection circuitry supports system monitoring. Four high-voltage wake-up inputs offer external wake-event detection without requiring every wake function to be duplicated at the MCU. Designers should verify regulator current capability, startup behavior, and CAN transceiver timing against the exact transmission-control requirements. The integration advantage is reduced external circuitry, while the main responsibility is preserving adequate layout separation between sensitive logic and automotive supply transients.

🧩

Automotive Sensor Node

A compact automotive sensor node can use the MC33989DW when it needs local wake-up detection, regulated power, monitoring, and CAN communication. The four high-voltage inputs provide a path for sensing external wake events, while the 1.0 Mbaud CAN physical interface connects the node to a wider vehicle network. Two voltage regulators and VSUP monitoring consolidate supply functions around the host MCU, reducing board-level component count. The 28-SOIC package still requires careful routing of supply, ground, wake, SPI, and CAN signals. For nodes with severe temperature, vibration, ESD, or transient requirements, confirm the relevant ratings in the NXP manufacturer datasheet. The device is most advantageous when several local functions can share one IC rather than separate discrete blocks.

🏭

Industrial CAN Gateway

The MC33989DW can support an industrial CAN gateway that combines network communication with local supply supervision and MCU support. Its CAN physical interface operates up to 1.0 Mbaud, and the SPI interface permits a host processor to configure or supervise the gateway. The two integrated regulators may reduce the external power-tree size, while VSUP monitoring and fault detection help the controller respond to abnormal conditions. Four high-voltage wake-up inputs can detect system events when the gateway must remain responsive without continuously running every subsystem. The 5.5 V to 18 V range suits many industrial supply architectures, but engineers must verify startup sequencing, transient tolerance, grounding, and the precise regulator load capability before approving the design for industrial use.

✈️

Transportation Equipment Controller

Transportation equipment controllers benefit from the MC33989DW when a rugged system requires CAN communication, wake-up detection, and local supply regulation in one interface IC. The 1.0 Mbaud CAN transceiver supports high-speed network traffic, while the SPI connection links it to the controller's MCU. Two voltage regulators, VSUP monitoring, and fault-detection circuitry create a compact support network around the host processor. Four high-voltage wake-up inputs support event-driven restart behavior in vehicles or mobile machinery. Engineering validation should include the automotive datasheet's electrical limits, EMC behavior, thermal conditions, and PCB recommendations. The principal benefit is fewer separate interface components; the trade-off is that a single mixed-function device requires careful partitioning of sensitive logic, CAN routing, and high-current supply paths.

What is the MC33989DW?
The MC33989DW is a NXP Semiconductors system basis chip with a high-speed CAN transceiver, supplied in a 28-SOIC package. According to the NXP manufacturer datasheet, it combines two voltage regulators, four high-voltage wake-up inputs, a 1.0 Mbaud CAN physical interface, an SPI interface for the microcontroller, VSUP monitoring, and fault-detection circuitry in one monolithic device.
What are the key specifications of MC33989DW that engineers should know?
The MC33989DW combines a 5.5 V to 18 V supply range with a 1.0 Mbaud CAN interface and a 28-SOIC package. According to the NXP manufacturer datasheet, the same IC also integrates two voltage regulators, four high-voltage wake-up inputs, an SPI microcontroller interface, VSUP monitoring, and fault detection, allowing several ECU support functions to be consolidated around one device.
What is the operating voltage of MC33989DW?
The MC33989DW operates from 5.5 V to 18 V. According to the NXP manufacturer datasheet, this supply range applies to the integrated automotive system basis functions and the associated CAN physical interface. Designers should keep the complete board supply and transient requirements within that range and follow the datasheet's supply-decoupling and application-circuit guidance.
How fast is the CAN interface in MC33989DW?
The integrated CAN physical interface in the MC33989DW is capable of operation up to 1.0 Mbaud. According to the NXP manufacturer datasheet, the device also provides VSUP monitoring and fault detection alongside the transceiver. Bus length, termination, transceiver loopback behavior, and node timing still determine whether a particular installation can sustain the selected data rate.
Where can I download the MC33989DW datasheet PDF?
The official MC33989DW datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/MC33989.pdf. The document contains the authoritative pin descriptions, electrical characteristics, application information, and recommended external circuitry. Use its package drawing and pin-description table when assigning PCB tracks because the MC33989DW has 28 pins in an SOIC package.
Where can I find the MC33989DW pinout?
Use the pin-description table and package drawing in the NXP MC33989 manufacturer datasheet to locate the MC33989DW pinout. The device uses a 28-SOIC package, but numbering alone does not identify functions such as supply, CAN, SPI, regulator, wake-up, or monitor connections. Confirm every net against the official table before laying out or revising a board.
Where to buy MC33989DW online?
Use the Request a Quote form on this page to request MC33989DW availability, lead time, and order details. The component is identified as a 28-SOIC device from NXP Semiconductors, and the official NXP datasheet is available through the datasheet link on this page. Quote requests allow the exact suffix, quantity, and delivery requirements to be checked together.
What is the price of MC33989DW?
Request a current MC33989DW quotation through the Request a Quote form on this page. The quote should specify the required quantity, delivery location, and any target schedule so the exact 28-SOIC ordering configuration can be evaluated. Because market pricing and availability can change, use the live quotation rather than a static price reference.
What is the lead time for MC33989DW?
Submit an MC33989DW request through the Request a Quote form on this page to confirm current lead time and minimum-order requirements. Lead time can depend on order quantity, shipment destination, and current inventory position. Include the production schedule and required package quantity in the request so the commercial response reflects the actual build plan.
Is MC33989DW in stock?
Current MC33989DW stock should be confirmed through the Request a Quote form on this page. The device is listed by NXP Semiconductors in a 28-SOIC package, and the manufacturer datasheet identifies it as an automotive system basis chip with a 1.0 Mbaud CAN interface. Provide the required quantity and date so the fulfillment response can confirm allocation.
What is the difference between MC33989DW and MC3487DE4?
The MC33989DW integrates system-basis functions with a CAN physical interface in a 28-SOIC device, while the MC3487DE4 is a dedicated CAN transceiver option. According to the NXP manufacturer datasheet, MC33989DW also includes two voltage regulators, four wake-up inputs, VSUP monitoring, fault detection, and SPI control. MC3487DE4 is therefore not a like-for-like system basis replacement.
MC33989DW vs MC3488AP1 - which is better for an automotive ECU?
The MC33989DW is preferable when the design needs a consolidated ECU subsystem with a 1.0 Mbaud CAN physical interface, two voltage regulators, four wake-up inputs, SPI control, VSUP monitoring, and fault detection. The MC3488AP1 is better considered when a dedicated high-speed CAN physical-layer function is needed without the complete system basis integration. Their architectures and packages must be compared rather than treated as drop-in equivalents.
When should I choose MC33989DW over MC3487DE4?
Choose the MC33989DW when the host ECU benefits from local power regulation, wake-up detection, supply monitoring, fault detection, and CAN physical-layer functions integrated in one 28-SOIC device. Choose the MC3487DE4 when the board already handles those support functions separately and only requires a dedicated CAN transceiver. The MC33989DW's 5.5 V to 18 V supply range and 1.0 Mbaud capability define its integration role.
Is MC33989DW suitable for an industrial CAN controller?
The MC33989DW can suit industrial CAN controllers whose supply, wake-up, monitoring, and communication requirements align with its 5.5 V to 18 V operating range. According to the NXP manufacturer datasheet, it supports a 1.0 Mbaud CAN physical interface, SPI host communication, four high-voltage wake-up inputs, VSUP monitoring, and integrated fault detection. Automotive qualification and environmental requirements should be checked before final selection.
What can replace MC33989DW?
No confirmed drop-in replacement for the MC33989DW has been identified from the available cross-reference results. A valid replacement must use the same 28-SOIC footprint, preserve pin-to-pin connectivity, and provide equivalent 5.5 V to 18 V operation, CAN capability, regulators, wake-up inputs, SPI control, monitoring, and fault functions. Similar CAN transceivers are not automatically replaceable.
What is the best NXP equivalent for MC33989DW?
No NXP part is currently confirmed as a drop-in equivalent for the MC33989DW. According to the NXP manufacturer datasheet, the target combines an automotive 5.5 V to 18 V system basis architecture with two regulators, four wake-up inputs, a 1.0 Mbaud CAN interface, SPI control, VSUP monitoring, and fault detection. Use the NXP cross-reference service to locate any newly released successor, then verify every pin and electrical function.

بيانات مرجعية هندسية لـ MC33989DW — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the MC33989DW when an automotive or transportation controller needs more than a standalone CAN transceiver and can benefit from integrated regulation, wake-up detection, supply monitoring, fault detection, and SPI control. Its 5.5 V to 18 V range, 1.0 Mbaud CAN capability, two regulators, and four high-voltage wake-up inputs make it suitable for MCU-based subsystems that value a consolidated interface architecture. Select a dedicated transceiver such as MC3487DE4 or MC3488AP1 when the board already provides regulation, wake logic, monitoring, and fault handling and needs only the CAN physical layer. Treat those devices as architectural alternatives, not pin-compatible replacements. No confirmed drop-in substitute for the complete MC33989DW function set was identified, so any proposed replacement must undergo a pin-by-pin and function-by-function review before use.

المقارنة مع البدائل

المعامل هذا المنتج
Brand NXP Semiconductors
Package 28-SOIC, 0.295 inch by 7.50 mm width
Product Type System basis chip with high-speed CAN transceiver
Supply Voltage Range 5.5 V to 18 V
CAN Data Rate 1.0 Mbaud
Integrated Voltage Regulators 2
High-Voltage Wake-Up Inputs 4
Host Interface SPI
Supply Monitoring VSUP monitoring
Fault Detection Integrated fault-detection circuitry

أبرز الفروقات

  • Combines a CAN transceiver with system-basis functions (مقابلMC3487DE4)
  • Supports external wake-event detection (مقابلMC3488AP1)
  • Single-chip MCU support and power supervision (مقابلDiscrete CAN transceiver solution)

ملاحظات التصميم

Assign the PCB nets by consulting the 28-pin description table in the NXP manufacturer datasheet, then follow its recommended decoupling and application schematic. Place the required input, output, and logic-support components close to their associated pins. Because the device combines CAN signaling, wake-up inputs, regulators, SPI control, and monitoring in one package, route high-current and potentially noisy supply paths away from sensitive SPI traces wherever the recommended layout permits.

Confirm that the 5.5 V to 18 V operating range covers the complete power environment, including startup, vehicle transients, and regulated system tolerances. Use VSUP monitoring and the integrated fault-detection functions as part of the controller's protection strategy, but do not treat them as a substitute for board-level transient protection. Verify the regulator output limits, load currents, and startup sequence in the manufacturer datasheet before selecting external components.

Keep the CAN physical-layer section compact and follow the manufacturer's PCB recommendations for its connection. Maintain the specified relationship between CAN pins and external components, provide the required bus-side protection, and use a controlled ground-return path. Four high-voltage wake-up inputs may require suitable input conditioning; check their voltage limits and recommended thresholds before adding divider networks or protection components.

Do not treat a standalone CAN transceiver as a functional equivalent for the MC33989DW. The target also contains two voltage regulators, four high-voltage wake-up inputs, VSUP monitoring, fault detection, and SPI control. Likewise, do not infer that the 1.0 Mbaud CAN rating alone guarantees a long bus at that rate; node timing, termination, cable length, topology, and electromagnetic conditions remain part of the complete CAN design.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The MC33989 is identified by NXP as an automotive system basis chip. Specific RoHS, REACH, AEC-Q100 qualification, lead-free, halogen-free, and conflict-minerals declarations are not stated in the retrieved component information.

تم التحقق من البيانات في: 2026-11-11 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MC33989DW datasheet MC33989DW pinout MC33989DW datasheet pdf MC33989DW 28-SOIC MC33989DW application circuit MC33989DW CAN transceiver MC33989DW equivalent MC33989DW replacement MC33989DW cross reference MC33989DW price MC33989DW stock NXP MC33989DW MC33989DW 1.0 Mbaud MC33989DW 5.5V 18V MC33989DW automotive CAN

المكونات والمصطلحات ذات الصلة

NXP Semiconductors MC33989DW MC3487DE4 MC3488AP1 system basis chip SBC interface IC CAN transceiver Controller Area Network SPI automotive ECU electronic control unit VSUP monitoring fault detection high-voltage wake-up input 28-SOIC SOIC family surface mount 1.0 Mbaud 5.5 V to 18 V automotive power management
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر