MC33989DW - Automotive CAN System Basis Chip | NXP
N.º da peça: MC33989DW ✓ AtivoMC33989DW Visão geral
A system basis chip, or SBC, is an interface IC that consolidates functions normally distributed around a microcontroller in an automotive electronic control unit. Its position in the hierarchy is SBC → CAN interface IC → interface IC → semiconductor. Integrating power regulation, bus physical-layer functions, wake-up detection, and supply supervision reduces the component count and board area needed around the host microcontroller while preserving a structured diagnostic and control interface.
The MC33989DW combines a 1.0 Mbaud-capable CAN physical interface with an SPI host interface. Four high-voltage wake-up inputs allow the device to detect external wake events in an automotive environment. Two internal voltage regulators support the host power architecture, while VSUP monitoring and fault-detection circuitry provide supply-state supervision. These functions make the device suitable for compact ECU subsystems that require more than a standalone CAN transceiver.
Automotive electronics commonly separate a low-power communication domain from the main MCU supply domain. MC33989DW supports this architecture by combining a regulated supply path, CAN physical signaling, and wake-up detection in one package. The SPI connection gives the host processor access to control and status functions without requiring a separate external CAN controller. Because the device also performs supply monitoring, designers can base early-startup and fault-handling decisions around a dedicated system basis component.
Typical uses include body and comfort controllers, engine-control subsystems, transmission controllers, sensor nodes, and other automotive modules using CAN communication. It is also relevant to industrial or transportation equipment where a ruggedized supply range, local wake-up detection, and a high-speed CAN physical interface simplify the implementation around a microcontroller.
When laying out the circuit, place the device and its support components according to the pin-description and recommended-layout sections in the NXP manufacturer datasheet. Confirm the complete 28-pin mapping, supply decoupling requirements, CAN transceiver connection details, and external component values before releasing the PCB; the MC33989DW integrates several subsystems whose layout decisions can affect signal integrity and startup behavior.
This page organizes the MC33989DW electrical ratings, package information, practical design guidance, application fit, and verified drop-in replacement status. It also distinguishes a true pin-compatible replacement from a merely similar CAN transceiver so procurement and engineering teams can avoid assuming that a different package or architecture is electrically interchangeable.
Alternativas drop-in para MC33989DW — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MC33989DW (mesmo formato e footprint) — diferindo em Package.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasMC33989DW Especificações
| Product Type | System basis chip with high-speed CAN transceiver |
| Supply Voltage Range | 5.5 V to 18 V |
| CAN Data Rate | 1.0 Mbaud |
| Encapsulamento | 28-SOIC, 0.295 inch by 7.50 mm width |
| Integrated Voltage Regulators | 2 |
| High-Voltage Wake-Up Inputs | 4 |
| Host Interface | SPI |
| Supply Monitoring | VSUP monitoring |
| Fault Detection | Integrated fault-detection circuitry |
| Primary Application | Automotive electronic control units |
| CAN Physical Interface | 1 integrated high-speed CAN transceiver |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do MC33989DW 28-soic, 0.295 inch by 7.50 mm width
Configuração de pinos para MC33989DW (pacote 28-soic, 0.295 inch by 7.50 mm width). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para MC33989DW.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MC33989DW é adequado para 6 aplicaçãos: Automotive Engine Control Unit, Body Control Module, Transmission Control Electronics, Automotive Sensor Node, Industrial CAN Gateway, Transportation Equipment Controller.
Automotive Engine Control Unit
The MC33989DW fits an automotive engine-control unit that needs a consolidated interface between its MCU and vehicle networks. Its 1.0 Mbaud CAN physical interface handles the CAN connection, while the SPI interface gives the host processor access to control and status functions. Two integrated voltage regulators and VSUP monitoring support the ECU power architecture. With a 5.5 V to 18 V operating range and four high-voltage wake-up inputs, the device can also support low-power wake behavior. The implementation trade-off is that several subsystems share one package, so pin assignment, transient protection, grounding, and decoupling must follow the manufacturer's application and layout guidance.
Recomendado
Body Control Module
A body control module can use the MC33989DW to combine CAN communications with local power-management and wake-up functions. The 1.0 Mbaud CAN physical interface serves the vehicle network, while four high-voltage wake-up inputs detect external activity that can transition a parked module into operation. The two internal regulators reduce the number of separate supply components around the MCU, and VSUP monitoring assists the controller in identifying abnormal supply conditions. Because the package is a 28-SOIC, the design must account for the integrated functions when planning board area and protection. The 5.5 V to 18 V range is suitable for many 12 V automotive systems, subject to transient and load-dump requirements specified in the datasheet.
Recomendado
Transmission Control Electronics
The MC33989DW is suitable for transmission-control electronics that combine a microcontroller, CAN communications, and supervised power rails. The device's CAN physical interface supports operation up to 1.0 Mbaud, while its SPI connection provides a straightforward host-control path. Integrated voltage regulators can supply compatible MCU domains, and fault-detection circuitry supports system monitoring. Four high-voltage wake-up inputs offer external wake-event detection without requiring every wake function to be duplicated at the MCU. Designers should verify regulator current capability, startup behavior, and CAN transceiver timing against the exact transmission-control requirements. The integration advantage is reduced external circuitry, while the main responsibility is preserving adequate layout separation between sensitive logic and automotive supply transients.
Recomendado
Automotive Sensor Node
A compact automotive sensor node can use the MC33989DW when it needs local wake-up detection, regulated power, monitoring, and CAN communication. The four high-voltage inputs provide a path for sensing external wake events, while the 1.0 Mbaud CAN physical interface connects the node to a wider vehicle network. Two voltage regulators and VSUP monitoring consolidate supply functions around the host MCU, reducing board-level component count. The 28-SOIC package still requires careful routing of supply, ground, wake, SPI, and CAN signals. For nodes with severe temperature, vibration, ESD, or transient requirements, confirm the relevant ratings in the NXP manufacturer datasheet. The device is most advantageous when several local functions can share one IC rather than separate discrete blocks.
Recomendado
Industrial CAN Gateway
The MC33989DW can support an industrial CAN gateway that combines network communication with local supply supervision and MCU support. Its CAN physical interface operates up to 1.0 Mbaud, and the SPI interface permits a host processor to configure or supervise the gateway. The two integrated regulators may reduce the external power-tree size, while VSUP monitoring and fault detection help the controller respond to abnormal conditions. Four high-voltage wake-up inputs can detect system events when the gateway must remain responsive without continuously running every subsystem. The 5.5 V to 18 V range suits many industrial supply architectures, but engineers must verify startup sequencing, transient tolerance, grounding, and the precise regulator load capability before approving the design for industrial use.
Recomendado
Transportation Equipment Controller
Transportation equipment controllers benefit from the MC33989DW when a rugged system requires CAN communication, wake-up detection, and local supply regulation in one interface IC. The 1.0 Mbaud CAN transceiver supports high-speed network traffic, while the SPI connection links it to the controller's MCU. Two voltage regulators, VSUP monitoring, and fault-detection circuitry create a compact support network around the host processor. Four high-voltage wake-up inputs support event-driven restart behavior in vehicles or mobile machinery. Engineering validation should include the automotive datasheet's electrical limits, EMC behavior, thermal conditions, and PCB recommendations. The principal benefit is fewer separate interface components; the trade-off is that a single mixed-function device requires careful partitioning of sensitive logic, CAN routing, and high-current supply paths.
Recomendado
Dados de referência de engenharia para MC33989DW — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Brand | NXP Semiconductors |
| Package | 28-SOIC, 0.295 inch by 7.50 mm width |
| Product Type | System basis chip with high-speed CAN transceiver |
| Supply Voltage Range | 5.5 V to 18 V |
| CAN Data Rate | 1.0 Mbaud |
| Integrated Voltage Regulators | 2 |
| High-Voltage Wake-Up Inputs | 4 |
| Host Interface | SPI |
| Supply Monitoring | VSUP monitoring |
| Fault Detection | Integrated fault-detection circuitry |
Principais diferenciais
- Combines a CAN transceiver with system-basis functions (vs MC3487DE4)
- Supports external wake-event detection (vs MC3488AP1)
- Single-chip MCU support and power supervision (vs Discrete CAN transceiver solution)
Notas de projeto
Assign the PCB nets by consulting the 28-pin description table in the NXP manufacturer datasheet, then follow its recommended decoupling and application schematic. Place the required input, output, and logic-support components close to their associated pins. Because the device combines CAN signaling, wake-up inputs, regulators, SPI control, and monitoring in one package, route high-current and potentially noisy supply paths away from sensitive SPI traces wherever the recommended layout permits.
Confirm that the 5.5 V to 18 V operating range covers the complete power environment, including startup, vehicle transients, and regulated system tolerances. Use VSUP monitoring and the integrated fault-detection functions as part of the controller's protection strategy, but do not treat them as a substitute for board-level transient protection. Verify the regulator output limits, load currents, and startup sequence in the manufacturer datasheet before selecting external components.
Keep the CAN physical-layer section compact and follow the manufacturer's PCB recommendations for its connection. Maintain the specified relationship between CAN pins and external components, provide the required bus-side protection, and use a controlled ground-return path. Four high-voltage wake-up inputs may require suitable input conditioning; check their voltage limits and recommended thresholds before adding divider networks or protection components.
Do not treat a standalone CAN transceiver as a functional equivalent for the MC33989DW. The target also contains two voltage regulators, four high-voltage wake-up inputs, VSUP monitoring, fault detection, and SPI control. Likewise, do not infer that the 1.0 Mbaud CAN rating alone guarantees a long bus at that rate; node timing, termination, cable length, topology, and electromagnetic conditions remain part of the complete CAN design.
Informações de conformidade
The MC33989 is identified by NXP as an automotive system basis chip. Specific RoHS, REACH, AEC-Q100 qualification, lead-free, halogen-free, and conflict-minerals declarations are not stated in the retrieved component information.