MC74F169N - 4-Bit Binary Up/Down Counter | onsemi
MPN: MC74F169N ✓ نشطMC74F169N نظرة عامة
A counter is a sequential digital circuit that stores a binary number and changes that number when a clock edge arrives. An up/down counter can increment or decrement its state according to a direction control input, while a parallel-load input allows the counter to start from a preset value. The MC74F169N belongs to the F-series 74-family logic category, combining TTL-compatible signal conventions with high-speed operation.
Key features include 4-bit counting capacity, a 4.5 V to 5.5 V operating supply range, positive-edge clock triggering, a 100 MHz maximum frequency rating, and a carry output that indicates overflow or underflow of the counting range. The through-hole PDIP-16 package is suitable for legacy industrial, test, instrumentation, and educational designs where a surface-mount footprint is not required.
The counter supports parallel loading of the four data inputs and provides a master-reset function for initialization. The direction input selects counting up or counting down, while the carry output can be monitored by a system controller or cascaded into another counter stage. Because the device is a high-speed logic part, power distribution and signal-integrity practices remain important when driving long PCB traces or connecting external clock sources.
Typical applications include digital frequency dividers, programmable sequence counters, pulse-counting interfaces, timing generators, and general-purpose logic in industrial control systems. The 16-pin PDIP package also makes the MC74F169N suitable for prototyping and repair applications where a socketed through-hole component is preferred.
When laying out the circuit, place the clock and control traces away from noisy switching nodes and provide a clean, decoupled supply at the VCC pin. Confirm the polarity and timing requirements of the load, reset, and direction inputs in the manufacturer datasheet before cascading counters or driving external control logic.
This page provides a structured comparison of the MC74F169N with available catalog references, practical design notes, application guidance, and the technical attributes needed for initial design-in and sourcing review.
بدائل مباشرة لـ MC74F169N — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلMC74F169N الحدود القصوى والخصائص الكهربائية
| الوظيفة | 4-bit binary up/down counter |
| Logic Type | Counter IC |
| Counting Elements | 1 element, 4 bit |
| Counter Type | Binary counter with up/down direction control |
| Clock Edge | Positive edge |
| Maximum Operating Frequency | 100 MHz |
| Supply Voltage Range | 4.5 V to 5.5 V |
| درجة حرارة التشغيل | 0 °C to 70 °C (TA) |
| العلبة | 16-PDIP, 0.300 in / 7.62 mm pitch |
| نوع التركيب | Through hole |
| عدد الدبابيس | 16 |
| نوع الخرج | Binary counter outputs |
| Reset Type | Master reset |
| Load Function | Parallel load |
تكوين أطراف MC74F169N
| دبوس 1 | CLK — Positive-edge clock input |
| دبوس 2 | MR — Master-reset input |
| دبوس 3 | LOAD — Parallel-load control input |
| دبوس 4 | A — Parallel data input A, least significant bit |
| دبوس 5 | B — Parallel data input B |
| دبوس 6 | C — Parallel data input C |
| دبوس 7 | D — Parallel data input D, most significant bit |
| دبوس 8 | GND — Ground reference |
| دبوس 9 | QD — Counter output D, most significant bit |
| دبوس 10 | QC — Counter output C |
| دبوس 11 | QB — Counter output B |
| دبوس 12 | QA — Counter output A, least significant bit |
| دبوس 13 | CARRY — Carry or terminal-count output |
| دبوس 14 | U/D — Count-direction control input |
| دبوس 15 | VCC — Positive power supply |
| دبوس 16 | NC — Not connected (per standard 74F169 pin arrangement) |
التطبيقات النموذجية
MC74F169N مناسب لـ 6 التطبيقs: Digital Frequency Divider, Industrial Sequence Control, Pulse-Counter Interface, Timing and Retiming Circuit, Test and Measurement Equipment, Legacy Control System Retrofit.
Digital Frequency Divider
The MC74F169N is well suited to frequency division because it provides a 4-bit synchronous counter with a 100 MHz maximum operating frequency. Use one output as the feedback clock for the next stage when a divide-by-16 ratio is required, or cascade multiple packages for larger division ratios. The positive-edge clock, master reset, and parallel-load inputs support initialization at a known count value. Keep feedback routing short and avoid long stub traces because setup and hold timing around the clock edge becomes tighter as the stage count increases.
موصى به
Industrial Sequence Control
The MC74F169N can implement a compact binary sequence controller in legacy industrial equipment, where a dedicated microcontroller would add unnecessary cost and complexity. The parallel-load input allows the counter to jump to a preset state, the direction input selects increasing or decreasing sequences, and the carry output flags the end of a counting range. Its 0 °C to 70 °C catalog temperature range and PDIP-16 package are appropriate for many indoor control panels, provided the enclosure temperature remains within the device rating.
موصى به
Pulse-Counter Interface
A positive-edge counter provides a simple interface for counting pulses from an encoder, frequency generator, or timing reference. The MC74F169N can count up to 100 MHz under specified conditions, giving it ample margin for many digital pulse sources. Add a line receiver, inverter, or Schmitt-trigger stage when the external waveform has slow edges, excessive noise, or a different voltage reference. The four output bits can drive a display controller, comparator, or programmable logic block that interprets the accumulated count.
موصى به
Timing and Retiming Circuit
The MC74F169N can divide a system clock to create a lower-rate timing reference for sequential logic, strobes, or data-capture systems. A feedback-connected stage produces predictable division ratios and keeps the derived clock edge aligned with the counter's synchronous operation. The maximum 100 MHz rating allows the input clock to remain well above the frequency needed by downstream timing logic. For fan-out-sensitive designs, keep the divided clock trace short and buffer it when driving multiple loads.
موصى به
Test and Measurement Equipment
Instrumentation designs can use the MC74F169N to count test pulses, divide a reference frequency, or generate repeatable timing intervals for measurement sequencing. The four parallel outputs provide direct access to multiple binary bits, while master reset establishes a repeatable starting condition between measurements. Its through-hole PDIP-16 package is especially convenient for laboratory prototypes, socketed assemblies, and repair platforms. Verify the timing budget for the external instrument bus before using the carry output as a trigger.
موصى به
Legacy Control System Retrofit
The MC74F169N is useful when maintaining or replicating older control hardware that uses a 16-pin TTL-compatible counter rather than a modern microcontroller. The through-hole package, 4.5 V to 5.5 V supply requirement, and simple counter function support board-level repairs and functional replacements. Before fitting the device, confirm that the existing board provides the expected clock polarity, load, reset, and direction logic levels. Compare the candidate's pinout and timing diagrams rather than relying on the 74-family function name alone.
موصى به
بيانات مرجعية هندسية لـ MC74F169N — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
ملاحظات التصميم
Place the supply bypass capacitor close to the VCC and GND pins, and route the return current through the same region to minimize loop area. Because the MC74F169N is specified for 4.5 V to 5.5 V, verify the board-level 5 V rail tolerance before power-up. Do not substitute a lower-voltage rail without checking every input and output level.
Keep the clock trace short and avoid branching stubs, particularly when the operating frequency approaches 100 MHz. Use a ground reference adjacent to the clock route, and terminate or buffer the signal when driving a cable, long trace, or high fan-out load. Slow clock edges can cause timing errors even when the nominal frequency is well below the maximum rating.
Do not assume that any 4-bit up/down counter is interchangeable with the MC74F169N. Confirm the 16-pin PDIP pin assignment, parallel-load polarity, master-reset behavior, carry-output function, and direction-control convention against the datasheet. A function-compatible part with different control polarity or output timing can prevent the counter from resetting, load, or count as intended.
معلومات الامتثال
The catalog information confirms the onsemi origin and 16-PDIP package, but no specific RoHS, REACH, lead-free, or halogen-free declaration was identified for this exact orderable MPN.