Microchip Technology

MCP3002T-I/ST - 10-Bit Dual-Channel SPI ADC | Microchip

MPN: MCP3002T-I/ST ✓ نشط
2.7 V Vdss 8-pin TSSOP Package
الحد الأدنى للطلب: 1 |

MCP3002T-I/ST نظرة عامة

The Microchip Technology MCP3002T-I/ST is a 10-bit dual-channel successive-approximation analog-to-digital converter with a 2.7 V minimum supply voltage, two analog input channels, and an SPI serial interface, packaged in an 8-pin TSSOP. It combines onboard sample-and-hold circuitry with a compact format for embedded control systems.

An ADC is a semiconductor that converts an analog voltage into a digital number for processing by a microcontroller or another digital controller. The MCP3002 belongs to the successive-approximation ADC family, where an internal sample-and-hold circuit measures an analog input and a successive-approximation register performs the conversion. Its two-channel arrangement supports dual analog measurements without requiring two separate converter packages.

The device provides 10-bit conversion resolution, a two-channel input configuration, and SPI communication. These characteristics make it suitable for reading potentiometers, temperature sensors, pressure sensors, and other externally conditioned analog signals. Its 8-pin TSSOP package also supports compact embedded-control layouts where board area and external connection count are important design constraints.

SPI communication provides a straightforward connection to a host microcontroller because the converter uses dedicated serial-data and chip-select signals. The host controls sampling by asserting chip select and then exchanges conversion commands and output data over the serial interface. Exact sampling rate, input impedance, conversion-time, reference-voltage, and operating-temperature details should be taken from the manufacturer datasheet before setting the acquisition timing and signal-conditioning network.

Typical uses include industrial control panels, environmental monitoring, laboratory instrumentation, and consumer equipment with one or two slowly changing analog inputs. In these systems, the MCP3002T-I/ST can convert conditioned sensor voltages into 10-bit values while the SPI interface shares communication wiring with other serial peripherals.

A key design consideration is analog reference quality. The reference connection must be adequately decoupled, and sensor outputs must remain within the converter's allowed input range. Place the decoupling capacitor close to the supply and reference pins, route the analog input away from fast SPI edges, and verify conversion timing against the host clock before increasing the sampling frequency.

This product page combines the manufacturer electrical description, package information, application guidance, comparison parameters, and practical PCB considerations so engineers can evaluate the MCP3002T-I/ST before integrating it into an embedded analog-measurement design.

بدائل مباشرة لـ MCP3002T-I/ST — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع MCP3002T-I/ST (نفس عامل الشكل والبصمة) — يختلف في Digital Interface, Input Configuration, Package, Sample-and-Hold Circuitry.

Microchip Technology
Digital Interface: SPI, modes 0,0 and 1,1
Input Configuration: 1 pseudo-differential pair or 2 single-ended inputs
Package: 8-TSSOP

MCP3002-I/ST

✅ بديل مباشر
Microchip Technology
📦 8-TSSOP
10 bit · Successive approximation register (SAR) · 2 inputs · 1 pseudo-differential pair or 2 single-ended inputs · 200 ksps · 2.7 V minimum · SPI, modes 0,0 and 1,1 · On-board

تواصل لمعرفة السعر

عرض ورقة البيانات ←

MCP3002T-I/ST الحدود القصوى والخصائص الكهربائية

ADC Type Successive Approximation (SAR)
الدقة 10 bit
Number of Analog Input Channels 2 channels
Input Configuration 1, 2 input
Minimum Supply Voltage 2.7 V
Digital Interface SPI
Sample-and-Hold Circuitry Onboard
العلبة 8-pin TSSOP
نوع التركيب Surface mount
Industrial Temperature Grade -I grade

تكوين أطراف MCP3002T-I/ST

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
دبوس 1 VREF — Positive reference-voltage input
دبوس 2 VREF- — Negative reference or analog-ground connection
دبوس 3 VIN- — Negative analog input channel
دبوس 4 VIN+ — Positive analog input channel
دبوس 5 GND — Ground connection
دبوس 6 DIN — SPI serial data input
دبوس 7 DOUT — SPI serial data output
دبوس 8 CS/SHDN — Chip-select and shutdown control input

التطبيقات النموذجية

MCP3002T-I/ST مناسب لـ 6 التطبيقs: Industrial Sensor Acquisition, Environmental Monitoring, Control Panel Interface, Laboratory Instrumentation, Battery-Powered Embedded Devices, Automotive Control Module.

🏭

Industrial Sensor Acquisition

The MCP3002T-I/ST fits industrial sensor acquisition when a controller must digitize two conditioned analog signals with limited PCB space. Its 10-bit resolution, two-channel SAR architecture, and SPI interface allow the host processor to share serial wiring with other peripherals. The 8-pin TSSOP package reduces board area compared with larger SOIC implementations, while onboard sample-and-hold circuitry supports the sampled-acquisition role. The signal-conditioning design must keep both inputs within the datasheet limits and preserve adequate source impedance at the sampling instant.

🧩

Environmental Monitoring

The MCP3002T-I/ST is suitable for environmental monitoring systems that combine temperature, humidity, or gas-sensor outputs with a digital controller. Two analog channels allow one package to acquire more than one conditioned measurement, while the 10-bit SAR ADC provides a compact numerical representation for scaling and filtering. SPI communication keeps the connection deterministic and economical for small embedded boards. Choose suitable sensor excitation, analog filtering, and reference decoupling so sensor transients do not compromise the sampled voltage or disturb neighboring signals.

🔧

Control Panel Interface

The MCP3002T-I/ST can serve as the analog input stage of a compact control panel that measures potentiometer positions, setpoints, or simple feedback voltages. Two inputs permit shared acquisition of two controls, and the SPI serial interface connects efficiently to a panel controller. The 10-bit result can be mapped into each control's calibrated range after conversion. Because human-operated controls may move slowly, the design can favor input filtering and stable reference routing over maximum conversion frequency, subject to the manufacturer's timing limits.

🖥️

Laboratory Instrumentation

The MCP3002T-I/ST is appropriate for compact laboratory instruments that digitize low-bandwidth analog measurements such as potentiometer outputs, detector signals, or calibrated process inputs. Its two analog inputs reduce the number of converter packages, and the 10-bit SAR architecture provides a straightforward digital result for calibration and display processing. The SPI interface also leaves the host processor available for measurement control. Instrument accuracy ultimately depends on the analog front end, reference implementation, grounding, and calibration strategy rather than digital resolution alone.

⚡

Battery-Powered Embedded Devices

The MCP3002T-I/ST can support compact battery-powered devices that periodically measure one or two analog quantities and then place the controller into a low-activity state between samples. The 2.7 V minimum supply supports integration with appropriately designed low-voltage rails, while the small TSSOP package preserves board area. SPI allows the host to control acquisition and avoid leaving the converter active continuously. The final power budget should include the host, sensors, reference circuitry, and the ADC across both active-conversion and idle periods.

🚗

Automotive Control Module

The MCP3002T-I/ST can be evaluated for low-speed automotive control functions that require two analog measurements and a compact converter package. The industrial-grade order code and 10-bit dual-channel SAR architecture are useful starting attributes, but the automotive design must verify the exact temperature range, qualification status, electrical limits, and any OEM requirements from the manufacturer documentation. Robust grounding, transient protection, reference stability, and diagnostic coverage remain board-level responsibilities and must be assessed independently of the basic ADC selection.

What is the MCP3002T-I/ST?
The MCP3002T-I/ST is a Microchip Technology 10-bit, dual-channel successive-approximation ADC with an SPI interface in an 8-pin TSSOP package. According to the Microchip manufacturer datasheet 21294E, it includes onboard sample-and-hold circuitry and operates from a 2.7 V minimum supply. The device is intended for embedded systems that need to measure two analog signals through a compact serial interface.
How many bits and analog input channels does MCP3002T-I/ST have?
The MCP3002T-I/ST provides a 10-bit conversion result and supports two analog input channels. The manufacturer describes it as a 2-channel SAR ADC with one- or two-input operation. According to the Microchip manufacturer datasheet 21294E, the two-channel capability makes it suitable for embedded controllers that must acquire more than one sensor or control signal without using two separate ADC packages.
What is the supply voltage of MCP3002T-I/ST?
The MCP3002T-I/ST operates from a minimum supply voltage of 2.7 V. The Microchip manufacturer datasheet 21294E identifies the device as a 2.7 V dual-channel 10-bit ADC, allowing it to fit systems that cannot accommodate a higher minimum supply. Use the datasheet's absolute-maximum and recommended operating limits when designing the power rail and decoupling network.
Where can I download the MCP3002T-I/ST datasheet PDF?
The official MCP3002T-I/ST datasheet PDF is available from Microchip Technology at the manufacturer URL listed on this page. The document identifies the MCP3002 as a 2.7 V, dual-channel, 10-bit successive-approximation ADC with an SPI serial interface. Download it for the authoritative pin descriptions, electrical characteristics, timing information, and application guidance.
Where is the MCP3002T-I/ST pinout located?
The MCP3002T-I/ST pinout is shown in the Microchip manufacturer datasheet 21294E, which is linked on this page. The device uses an 8-pin TSSOP package with VREF, VREF-, VIN-, VIN+, GND, DIN, DOUT, and CS/SHDN connections. Use the pin-description table when assigning PCB tracks because analog, ground, digital, and chip-select signals have different routing requirements.
What are the key specifications of MCP3002T-I/ST that engineers should know?
The key specifications are a 10-bit conversion resolution, two analog input channels, SAR architecture, onboard sample-and-hold circuitry, a 2.7 V minimum supply, and an SPI interface. The Microchip manufacturer datasheet 21294E also identifies an 8-pin TSSOP package. These parameters define its suitability for compact embedded acquisition systems, while conversion timing and input-range details must be read from the electrical tables.
Can MCP3002T-I/ST measure two analog sensors?
Yes, the MCP3002T-I/ST can measure two analog input channels and is suited to dual-sensor acquisition. According to the Microchip manufacturer datasheet 21294E, it uses onboard sample-and-hold circuitry with a 10-bit SAR converter. Each sensor output must be conditioned to remain within the converter's supported input range, and the SPI timing must provide enough clock cycles for each conversion.
How does MCP3002T-I/ST communicate with a microcontroller?
The MCP3002T-I/ST communicates with a host microcontroller through its SPI serial interface. The interface uses dedicated chip-select, serial-input, and serial-output pins, allowing the host to initiate a conversion and read the digital result. According to the Microchip manufacturer datasheet 21294E, the SPI command sequence and conversion timing must be implemented exactly as documented.
Where can I buy MCP3002T-I/ST online and check its price?
Use the Request a Quote form on this page to ask about MCP3002T-I/ST availability, commercial terms, and lead time. The form is the appropriate route for a quote-first electronic-component purchase and avoids publishing a price that may change with quantity and market conditions. The exact package suffix, industrial grade, and tape-and-reel order code should be included in the request.
What is the lead time and minimum order quantity for MCP3002T-I/ST?
Request the current MCP3002T-I/ST lead time and minimum order quantity through the Request a Quote form on this page. The MCP3002T-I/ST order code identifies the tape-and-reel industrial-temperature variant, so include the complete MPN when asking for a quotation. A complete quotation should also confirm reel quantity, manufacturer packaging, and the delivery schedule.
Is MCP3002T-I/ST in stock?
Current MCP3002T-I/ST stock should be confirmed through the Request a Quote form on this page. The form allows the quantity, reel configuration, target location, and required schedule to be included in the request. Because inventory and lead time can change, treat them as commercial terms to be confirmed rather than fixed product characteristics.
What is the difference between MCP3002T-I/ST and MCP3002T-I/SN?
MCP3002T-I/ST and MCP3002T-I/SN share the 10-bit, dual-channel SAR ADC function and SPI interface, but their package suffixes indicate different lead-free package options: ST corresponds to the 8-pin TSSOP format, while SN corresponds to the 8-pin SOIC format. Because the physical packages differ, MCP3002T-I/SN is not a drop-in replacement for an existing MCP3002T-I/ST footprint.
When should I choose MCP3002T-I/ST over another 10-bit ADC?
Choose the MCP3002T-I/ST when the design needs two analog channels, 10-bit resolution, SPI communication, a 2.7 V minimum supply, and an 8-pin TSSOP footprint. It is especially appropriate for compact embedded-control boards. Confirm acquisition rate, analog input range, reference requirements, and temperature limits in the manufacturer datasheet before finalizing the selection.
Is MCP3002T-I/ST suitable for industrial embedded control?
The MCP3002T-I/ST is appropriate for many industrial embedded-control applications because it combines two analog input channels, 10-bit resolution, SPI control, and an industrial-grade order code. The Microchip manufacturer datasheet 21294E remains the controlling document for the exact operating temperature range, accuracy, electrical limits, and qualification status. Ambient-temperature and enclosure requirements should be evaluated separately.
What can replace MCP3002T-I/ST on the same PCB footprint?
A replacement for MCP3002T-I/ST must match its 8-pin TSSOP footprint, pin functions, SPI protocol, 10-bit resolution, two-channel capability, and electrical limits. The verified cross-reference results do not identify a distinct drop-in replacement with those confirmed characteristics, so no alternative is claimed here. Treat a proposed substitute as unqualified until its datasheet and PCB land pattern have been reviewed.
Is there a Microchip equivalent that can replace MCP3002T-I/ST?
No distinct drop-in equivalent is established by the available manufacturer and cross-reference information. MCP3002-I/ST has the same core MCP3002 electrical function but represents a different order-code variant, while MCP3002T-I/SN uses a different physical package. A valid replacement must preserve the MCP3002T-I/ST TSSOP land pattern and SPI command compatibility rather than merely providing equivalent ADC resolution.

بيانات مرجعية هندسية لـ MCP3002T-I/ST — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the MCP3002T-I/ST when an embedded design requires two analog channels, 10-bit resolution, SPI communication, a 2.7 V minimum supply, and an 8-pin TSSOP footprint. It is a strong fit for compact industrial controls, environmental monitoring, laboratory instruments, and low-speed battery-powered equipment. The ST package should not be interchanged directly with the SN SOIC variant without changing the PCB footprint. Before final selection, verify conversion time, accuracy, input range, reference requirements, operating temperature, and qualification status in the manufacturer datasheet. No distinct drop-in substitute is claimed without confirmed pin, protocol, and electrical compatibility. If the design requires a different package, channel count, resolution, interface, or automotive qualification, evaluate those requirements as deliberate redesign decisions rather than treating a merely similar ADC as a drop-in replacement.

المقارنة مع البدائل

المعامل هذا المنتج
Package 8-pin TSSOP
Brand Microchip Technology
ADC Architecture Successive Approximation (SAR)
Resolution 10 bit
Analog Input Channels 2 channels
Minimum Supply Voltage 2.7 V
Digital Interface SPI
Sample-and-Hold Circuitry Onboard

أبرز الفروقات

  • Two analog channels in a compact TSSOP converter (مقابلSingle-channel ADC solutions)
  • Low minimum operating supply (مقابلADCs requiring a higher minimum supply)
  • Compact 8-pin surface-mount implementation (مقابلLarger-package SOIC implementations)

ملاحظات التصميم

Route VIN+ and VIN- away from the DIN and DOUT traces, especially the high-speed clock edge entering DIN. Place the analog input network close to pins 3 and 4, and keep the return path associated with the analog signal over a quiet ground plane. This separation reduces the chance that SPI coupling appears directly in the conversion result.

Place the manufacturer-recommended supply-decoupling capacitor directly between the supply and ground pins. Keep the VREF and VREF- connections short and provide the reference decoupling specified in the Microchip manufacturer datasheet 21294E. Reference stability is part of the measurement accuracy, so avoid routing VREF alongside switching-node or high-current return paths.

Do not treat the 10-bit result as a measurement reference for analog signals outside the converter's input range. Confirm source impedance, conversion timing, and the input sampling network against the datasheet, especially when a resistive divider or sensor output drives the input. Also verify that the SPI host supplies the documented clock interval before sampling a completed conversion.

Use a land pattern intended for the 8-pin TSSOP package and follow the manufacturer's board-layout guidance for exposed or thermal structures if applicable to the selected order code. Keep thermal-sensitive analog layout away from heat sources and maintain the specified copper and via arrangement around the package to preserve predictable electrical and thermal behavior.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The available manufacturer product and datasheet information does not explicitly state the requested compliance statuses. The -I order code identifies the industrial-temperature grade but does not by itself establish AEC-Q100 qualification.

تم التحقق من البيانات في: 2026-11-10 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MCP3002T-I/ST datasheet MCP3002T-I/ST datasheet pdf MCP3002T-I/ST pinout MCP3002T-I/ST specifications MCP3002T-I/ST equivalent MCP3002T-I/ST replacement MCP3002T-I/ST cross reference MCP3002T-I/ST TSSOP pinout MCP3002T-I/ST SPI ADC MCP3002T-I/ST dual channel ADC MCP3002T-I/ST price MCP3002T-I/ST stock Microchip MCP3002T-I/ST MCP3002T-I/ST sensor acquisition MCP3002T-I/ST industrial control

المكونات والمصطلحات ذات الصلة

Microchip Technology MCP3002T-I/ST MCP3002 MCP3002-I/ST MCP3002T-I/SN analog-to-digital converter ADC successive-approximation ADC SAR architecture SPI serial interface sample-and-hold circuit 10-bit resolution dual-channel ADC 2.7 V minimum supply 8-pin TSSOP TSSOP package family surface-mount package embedded control industrial sensor acquisition environmental monitoring reference voltage analog input RoHS REACH AEC-Q100
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر