MCP3002T-I/ST - 10-Bit Dual-Channel SPI ADC | Microchip
部品番号: MCP3002T-I/ST ✓ 生産中MCP3002T-I/ST 概要
An ADC is a semiconductor that converts an analog voltage into a digital number for processing by a microcontroller or another digital controller. The MCP3002 belongs to the successive-approximation ADC family, where an internal sample-and-hold circuit measures an analog input and a successive-approximation register performs the conversion. Its two-channel arrangement supports dual analog measurements without requiring two separate converter packages.
The device provides 10-bit conversion resolution, a two-channel input configuration, and SPI communication. These characteristics make it suitable for reading potentiometers, temperature sensors, pressure sensors, and other externally conditioned analog signals. Its 8-pin TSSOP package also supports compact embedded-control layouts where board area and external connection count are important design constraints.
SPI communication provides a straightforward connection to a host microcontroller because the converter uses dedicated serial-data and chip-select signals. The host controls sampling by asserting chip select and then exchanges conversion commands and output data over the serial interface. Exact sampling rate, input impedance, conversion-time, reference-voltage, and operating-temperature details should be taken from the manufacturer datasheet before setting the acquisition timing and signal-conditioning network.
Typical uses include industrial control panels, environmental monitoring, laboratory instrumentation, and consumer equipment with one or two slowly changing analog inputs. In these systems, the MCP3002T-I/ST can convert conditioned sensor voltages into 10-bit values while the SPI interface shares communication wiring with other serial peripherals.
A key design consideration is analog reference quality. The reference connection must be adequately decoupled, and sensor outputs must remain within the converter's allowed input range. Place the decoupling capacitor close to the supply and reference pins, route the analog input away from fast SPI edges, and verify conversion timing against the host clock before increasing the sampling frequency.
This product page combines the manufacturer electrical description, package information, application guidance, comparison parameters, and practical PCB considerations so engineers can evaluate the MCP3002T-I/ST before integrating it into an embedded analog-measurement design.
ドロップイン代替品: MCP3002T-I/ST — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCP3002T-I/ST (同一形状・フットプリント) — 相違点: Digital Interface, Input Configuration, Package, Sample-and-Hold Circuitry.
MCP3002-I/ST
✅ ドロップイン価格はお問い合わせください
データシートを見る →MCP3002T-I/ST 最大定格&電気的特性
| ADC Type | Successive Approximation (SAR) |
| 分解能 | 10 bit |
| Number of Analog Input Channels | 2 channels |
| Input Configuration | 1, 2 input |
| Minimum Supply Voltage | 2.7 V |
| Digital Interface | SPI |
| Sample-and-Hold Circuitry | Onboard |
| パッケージ | 8-pin TSSOP |
| 実装タイプ | Surface mount |
| Industrial Temperature Grade | -I grade |
MCP3002T-I/ST ピン構成
| ピン 1 | VREF — Positive reference-voltage input |
| ピン 2 | VREF- — Negative reference or analog-ground connection |
| ピン 3 | VIN- — Negative analog input channel |
| ピン 4 | VIN+ — Positive analog input channel |
| ピン 5 | GND — Ground connection |
| ピン 6 | DIN — SPI serial data input |
| ピン 7 | DOUT — SPI serial data output |
| ピン 8 | CS/SHDN — Chip-select and shutdown control input |
主な用途
MCP3002T-I/ST の用途: 6 件s: Industrial Sensor Acquisition, Environmental Monitoring, Control Panel Interface, Laboratory Instrumentation, Battery-Powered Embedded Devices, Automotive Control Module.
Industrial Sensor Acquisition
The MCP3002T-I/ST fits industrial sensor acquisition when a controller must digitize two conditioned analog signals with limited PCB space. Its 10-bit resolution, two-channel SAR architecture, and SPI interface allow the host processor to share serial wiring with other peripherals. The 8-pin TSSOP package reduces board area compared with larger SOIC implementations, while onboard sample-and-hold circuitry supports the sampled-acquisition role. The signal-conditioning design must keep both inputs within the datasheet limits and preserve adequate source impedance at the sampling instant.
おすすめ
Environmental Monitoring
The MCP3002T-I/ST is suitable for environmental monitoring systems that combine temperature, humidity, or gas-sensor outputs with a digital controller. Two analog channels allow one package to acquire more than one conditioned measurement, while the 10-bit SAR ADC provides a compact numerical representation for scaling and filtering. SPI communication keeps the connection deterministic and economical for small embedded boards. Choose suitable sensor excitation, analog filtering, and reference decoupling so sensor transients do not compromise the sampled voltage or disturb neighboring signals.
おすすめ
Control Panel Interface
The MCP3002T-I/ST can serve as the analog input stage of a compact control panel that measures potentiometer positions, setpoints, or simple feedback voltages. Two inputs permit shared acquisition of two controls, and the SPI serial interface connects efficiently to a panel controller. The 10-bit result can be mapped into each control's calibrated range after conversion. Because human-operated controls may move slowly, the design can favor input filtering and stable reference routing over maximum conversion frequency, subject to the manufacturer's timing limits.
おすすめ
Laboratory Instrumentation
The MCP3002T-I/ST is appropriate for compact laboratory instruments that digitize low-bandwidth analog measurements such as potentiometer outputs, detector signals, or calibrated process inputs. Its two analog inputs reduce the number of converter packages, and the 10-bit SAR architecture provides a straightforward digital result for calibration and display processing. The SPI interface also leaves the host processor available for measurement control. Instrument accuracy ultimately depends on the analog front end, reference implementation, grounding, and calibration strategy rather than digital resolution alone.
おすすめ
Battery-Powered Embedded Devices
The MCP3002T-I/ST can support compact battery-powered devices that periodically measure one or two analog quantities and then place the controller into a low-activity state between samples. The 2.7 V minimum supply supports integration with appropriately designed low-voltage rails, while the small TSSOP package preserves board area. SPI allows the host to control acquisition and avoid leaving the converter active continuously. The final power budget should include the host, sensors, reference circuitry, and the ADC across both active-conversion and idle periods.
おすすめ
Automotive Control Module
The MCP3002T-I/ST can be evaluated for low-speed automotive control functions that require two analog measurements and a compact converter package. The industrial-grade order code and 10-bit dual-channel SAR architecture are useful starting attributes, but the automotive design must verify the exact temperature range, qualification status, electrical limits, and any OEM requirements from the manufacturer documentation. Robust grounding, transient protection, reference stability, and diagnostic coverage remain board-level responsibilities and must be assessed independently of the basic ADC selection.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCP3002T-I/ST — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 8-pin TSSOP |
| Brand | Microchip Technology |
| ADC Architecture | Successive Approximation (SAR) |
| Resolution | 10 bit |
| Analog Input Channels | 2 channels |
| Minimum Supply Voltage | 2.7 V |
| Digital Interface | SPI |
| Sample-and-Hold Circuitry | Onboard |
主な差別化要因
- Two analog channels in a compact TSSOP converter (vs Single-channel ADC solutions)
- Low minimum operating supply (vs ADCs requiring a higher minimum supply)
- Compact 8-pin surface-mount implementation (vs Larger-package SOIC implementations)
設計ノート
Route VIN+ and VIN- away from the DIN and DOUT traces, especially the high-speed clock edge entering DIN. Place the analog input network close to pins 3 and 4, and keep the return path associated with the analog signal over a quiet ground plane. This separation reduces the chance that SPI coupling appears directly in the conversion result.
Place the manufacturer-recommended supply-decoupling capacitor directly between the supply and ground pins. Keep the VREF and VREF- connections short and provide the reference decoupling specified in the Microchip manufacturer datasheet 21294E. Reference stability is part of the measurement accuracy, so avoid routing VREF alongside switching-node or high-current return paths.
Do not treat the 10-bit result as a measurement reference for analog signals outside the converter's input range. Confirm source impedance, conversion timing, and the input sampling network against the datasheet, especially when a resistive divider or sensor output drives the input. Also verify that the SPI host supplies the documented clock interval before sampling a completed conversion.
Use a land pattern intended for the 8-pin TSSOP package and follow the manufacturer's board-layout guidance for exposed or thermal structures if applicable to the selected order code. Keep thermal-sensitive analog layout away from heat sources and maintain the specified copper and via arrangement around the package to preserve predictable electrical and thermal behavior.
コンプライアンス情報
The available manufacturer product and datasheet information does not explicitly state the requested compliance statuses. The -I order code identifies the industrial-temperature grade but does not by itself establish AEC-Q100 qualification.