Microchip Technology

MCP603T-E/CH - 2.8MHz R-R Op Amp | Microchip Technology

MPN: MCP603T-E/CH ✓ نشط
2.7 V to 6.0 V Vdss 230 uA Id SOT-23-6 Package
الحد الأدنى للطلب: 1 |

MCP603T-E/CH نظرة عامة

The Microchip Technology MCP603T-E/CH is a single, general-purpose operational amplifier with a 2.8 MHz gain-bandwidth product, 2.7 V to 6.0 V supply range, and approximately 230 uA typical operating current, housed in a 6-pin SOT-23 package. It provides a rail-to-rail output, shutdown capability, and low input-bias characteristics for low-power signal-conditioning designs.

An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify, buffer, filter, or compare small analog signals. The MCP603 belongs to the CMOS operational-amplifier family and operates from a single positive supply. Its rail-to-rail output allows the output to approach the supply limits, while shutdown control can reduce power consumption when the circuit is not active.

Key characteristics include a 2.8 MHz gain-bandwidth product, 4.5 V/us slew rate, 29 nV/sqrt(Hz) input noise at 1 kHz, and less than 2 mV typical offset voltage. The typical operating current of 230 uA supports battery-powered and portable systems, while the 2.7 V minimum supply voltage enables operation from low-voltage rails.

The MCP603 uses Microchip's advanced CMOS technology to provide low bias current and low power consumption in a compact surface-mount package. Reported input-bias current is 1 pA, input-offset current is 20 pA, and the device provides approximately 106 dB common-mode rejection. These characteristics are useful when the op amp must process high-impedance sensor signals without loading the source.

Typical applications include low-power sensor signal conditioning, battery-operated instrumentation, audio input stages, portable measurement systems, and general-purpose analog filtering. The shutdown function is valuable in duty-cycled systems because it allows the amplifier to be disabled when measurements are not required.

Designers should account for the 2.7 V minimum supply voltage and confirm that the selected operating point satisfies the amplifier's common-mode and output-swing requirements. Decoupling capacitors should be placed close to the supply pins, and unused inputs must be biased so the amplifier remains in a defined state. The SOT-23-6 footprint requires careful land-pattern compliance and adequate assembly clearance.

This product record combines the manufacturer specifications, package identification, operating characteristics, application guidance, and substitution analysis needed to evaluate the MCP603T-E/CH before PCB implementation or procurement.

بدائل مباشرة لـ MCP603T-E/CH — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

MCP603T-I/CH

✅ بديل مباشر
📦 SOT-23-6
Core key ratings are unchanged at 2.8 MHz gain-bandwidth product and 230 uA typical operating current, while the I-grade temperature classification differs from the E-grade target.

📋 بديل مرجعي (غير موجود في الكتالوج)

MCP603T-E/CH الحدود القصوى والخصائص الكهربائية

Amplifier Type General Purpose
Number of Circuits 1 circuit
Supply Voltage Range 2.7 V to 6.0 V
Gain-Bandwidth Product 2.8 MHz
Slew Rate 4.5 V/us
Typical Operating Current 230 uA
Input Offset Voltage 1 mV maximum; less than 2 mV typical
Input Bias Current 1 pA
Input Offset Current 20 pA
Input Voltage Noise Density 29 nV/sqrt(Hz) at 1 kHz
Common-Mode Rejection 106 dB
Input Offset Voltage Drift 2.5 uV/C
نطاق درجة حرارة التشغيل -40 C to +125 C
نوع الخرج Rail-to-Rail
Shutdown Function Enabled
ESD Protection Enabled
العلبة SOT-23-6
Packaging Cut Tape
حالة RoHS Compliant
Automotive Qualification AEC-Q100

دليل تكوين أطراف MCP603T-E/CH sot-23-6

تكوين الأطراف لـ MCP603T-E/CH (حزمة sot-23-6). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة sot-23-6 لـ MCP603T-E/CH

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MCP603T-E/CH.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

MCP603T-E/CH مناسب لـ 6 التطبيقs: Battery-Powered Sensor Conditioning, Portable Medical Signal Conditioning, Low-Power Audio Input Amplifier, Industrial Process Signal Amplifier, Portable Data Acquisition, Active Filtering and Buffering.

🧩

Battery-Powered Sensor Conditioning

The MCP603T-E/CH fits low-energy sensor front ends because its 230 uA typical operating current and 1 pA input-bias current reduce loading on battery-powered sources. Its 29 nV/sqrt(Hz) input noise at 1 kHz, less than 2 mV typical offset voltage, and 106 dB common-mode rejection support measurement of small changes superimposed on larger bias voltages. The amplifier can amplify a bridge, resistive, or current-based sensor output, although the selected circuit must keep the signal within the input common-mode range. Use the shutdown function between measurement intervals to reduce consumption when continuous amplification is unnecessary.

💊

Portable Medical Signal Conditioning

The MCP603T-E/CH can serve as the gain stage in compact medical monitoring equipment when the design prioritizes low power and a small footprint. Its 2.8 MHz gain-bandwidth product is suitable for signals in the audio and low-frequency physiological range, while the 106 dB common-mode rejection helps suppress interference coupled into high-impedance electrodes or sensor leads. The 1 pA input-bias current is valuable when source impedance is high. Designers must still assess patient-safety isolation, input protection, diagnostic accuracy, and applicable medical validation requirements; the amplifier qualification alone does not establish compliance for the finished instrument.

🎧

Low-Power Audio Input Amplifier

The MCP603T-E/CH is suitable for buffering low-level audio inputs in portable equipment because its rail-to-rail output and 4.5 V/us slew rate can reproduce small signals while operating from a 2.7 V to 6.0 V supply. The 2.8 MHz gain-bandwidth product provides useful bandwidth for audio-band amplification, and 230 uA typical operating current supports long battery life. In headphone, microphone, or auxiliary-input circuits, the output-load capability and distortion behavior should be checked at the selected voltage gain. Input and output filtering should target the intended audio bandwidth rather than unnecessarily amplifying noise outside it.

🏭

Industrial Process Signal Amplifier

The MCP603T-E/CH can condition low-level process signals in industrial control boards when the signal bandwidth is modest and the operating environment is extended. Its -40 C to +125 C temperature range supports demanding ambient conditions, while 106 dB common-mode rejection reduces the effect of common-mode noise on sensor lines. The 2.8 MHz closed-loop bandwidth and 4.5 V/us slew rate are adequate for many pressure, temperature, and position interfaces. Engineers should add appropriate input protection, verify the common-mode range at the actual supply voltage, and evaluate electromagnetic interference requirements at the board and enclosure level.

📟

Portable Data Acquisition

The MCP603T-E/CH is appropriate for a compact data-acquisition front end that converts a low-amplitude analog measurement into a voltage suitable for an ADC. Its 2.8 MHz gain-bandwidth product supports moderate closed-loop bandwidth, while its 29 nV/sqrt(Hz) input-noise density contributes relatively little noise in many sensor signals. The 1 pA bias current minimizes disturbance of high-impedance sources, and the shutdown function can support periodic sampling systems. Select the external gain carefully to preserve stability, include an anti-alias filter before the converter, and ensure that the amplifier can charge the ADC sample-and-hold input within the acquisition interval.

🔧

Active Filtering and Buffering

The MCP603T-E/CH can implement active low-pass, high-pass, or general biquad filter sections when a compact, low-power implementation is required. Its 2.8 MHz gain-bandwidth product provides useful closed-loop bandwidth for filters handling low-frequency or audio-range signals, while the 4.5 V/us slew rate helps preserve amplitude through rapidly varying waveforms. Component tolerances around the feedback network directly affect cutoff frequency and Q, so standard resistor and capacitor tolerances should be evaluated against the filter response. The rail-to-rail output improves usable signal range in single-supply circuits, but headroom limitations at high frequency and load must be checked using the manufacturer data.

ملخص المنتجات الموصى بها

MCP603T-I/CH Same-family low-power operational amplifier يُستخدم في: Battery-Powered Sensor Conditioning, Portable Medical Signal Conditioning, Low-Power Audio Input Amplifier, Industrial Process Signal Amplifier, Portable Data Acquisition, Active Filtering and Buffering
What is the operating voltage range of MCP603T-E/CH?
The MCP603T-E/CH operates from 2.7 V to 6.0 V. According to the Microchip manufacturer product information, this single-supply range supports low-voltage 3.3 V and 5 V systems. The 6.0 V upper limit is important for USB-powered and industrial designs because the device must not be operated above that voltage without appropriate protection.
What are the key specifications of MCP603T-E/CH that engineers should know?
The MCP603T-E/CH is a single general-purpose CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 4.5 V/us slew rate, 230 uA typical operating current, and rail-to-rail output. Microchip lists less than 2 mV typical offset voltage, 106 dB common-mode rejection, 29 nV/sqrt(Hz) input noise at 1 kHz, and a -40 C to +125 C operating-temperature range.
Where can I download the MCP603T-E/CH datasheet PDF?
The official MCP603 documentation is available through the Microchip MCP603 product page, which links to the manufacturer datasheet and supporting resources. Use the manufacturer's pin-description table and electrical-characteristics tables for the authoritative SOT-23-6 connection and limit information. Third-party copies can assist with archival reading, but the Microchip document should be used for design qualification.
Where can I find the MCP603T-E/CH pinout?
The MCP603T-E/CH pinout is defined for the 6-pin SOT-23 package in the Microchip MCP603 datasheet. Use the manufacturer pin-configuration drawing when assigning power, ground, inputs, output, and shutdown-control connections. The exposed physical orientation is SOT-23-6 rather than the 5-pin SOT-23 variant, so PCB designers should not use a generic 5-pin land pattern.
Is MCP603T-E/CH suitable for low-power sensor applications?
Yes, the MCP603T-E/CH is suitable for many low-power sensor signal-conditioning stages. Its typical operating current of 230 uA, 1 pA input-bias current, 20 pA input-offset current, and less than 2 mV typical offset voltage help preserve weak sensor signals. High-impedance sources still require leakage analysis because connector contamination and board leakage can exceed the amplifier's specified bias current.
What can replace the MCP603T-E/CH?
The closest same-family replacement identified for the MCP603T-E/CH is the MCP603T-I/CH because it retains the MCP603 single-amplifier architecture, SOT-23-6 package, 2.8 MHz gain-bandwidth class, and 2.7 V to 6.0 V supply operation. Its temperature-grade designation differs, so engineers should confirm the required ambient-temperature range and production qualifications before treating it as a direct substitution.
Is MCP603T-I/CH the same as MCP603T-E/CH?
The MCP603T-I/CH and MCP603T-E/CH are closely related MCP603 devices in the same 6-pin SOT-23 family, with matching core electrical characteristics including 2.8 MHz gain-bandwidth product and 230 uA typical operating current. Their temperature-grade suffixes indicate different qualification classes, so they are interchangeable only when the MCP603T-I/CH temperature rating and qualification status meet the target application's requirements.
MCP603T-E/CH vs MCP603T-I/CH - which is better for a temperature-sensitive design?
Choose MCP603T-E/CH for designs requiring operation across the stated -40 C to +125 C range, and choose MCP603T-I/CH only after checking its own temperature-grade limits. Both use the SOT-23-6 footprint and share the 2.8 MHz gain-bandwidth product, so the principal selection criterion is environmental qualification rather than signal-path bandwidth. Verify the exact ordering code and qualification status before release.
When should I choose MCP603T-E/CH over a lower-bandwidth amplifier?
Choose MCP603T-E/CH when a 2.8 MHz gain-bandwidth product and 4.5 V/us slew rate are needed for signal amplification or active filtering. The part is a general-purpose choice for single-supply, low-power designs, not necessarily an optimum choice for precision instrumentation, very low offset, or high-speed closed-loop applications. Its 230 uA typical operating current also makes it more suitable than a high-current amplifier for portable systems.
What is the best low-power amplifier replacement for MCP603T-E/CH?
The best same-family replacement identified is the MCP603T-I/CH because it preserves the MCP603's single-channel architecture and SOT-23-6 footprint while retaining the 2.8 MHz gain-bandwidth product and 230 uA typical operating current. A cross-brand substitute should not be selected solely from bandwidth and package similarity; input-bias current, offset, noise, shutdown polarity, common-mode range, and temperature grade must also be verified.
What is the noise performance of MCP603T-E/CH?
The MCP603T-E/CH has an input voltage-noise density of 29 nV/sqrt(Hz) at 1 kHz. This figure is most useful when estimating the amplifier's contribution to broadband input-referred noise. For a narrow measurement bandwidth, the result should be multiplied by the square root of the equivalent noise bandwidth, and source resistance and resistor noise must also be included.
How much current does MCP603T-E/CH consume?
The typical operating current of the MCP603T-E/CH is 230 uA. Microchip also identifies a 22 mA output-current capability in the device specifications. Actual supply consumption depends on operating state, output loading, and whether the shutdown function is asserted, so battery-life calculations should include the complete signal-chain load rather than the amplifier current alone.
Does MCP603T-E/CH have rail-to-rail output?
Yes, the MCP603T-E/CH has a rail-to-rail output. This allows the output voltage to swing more closely to the positive and negative supply limits than a conventional non-rail-to-rail output stage. The output still cannot be assumed to reach either rail exactly; designers should consult the manufacturer output-voltage swing and load-current limits for the chosen supply voltage.
Is MCP603T-E/CH RoHS compliant?
The MCP603T-E/CH is identified as RoHS compliant in its component listing. Microchip also associates the ordering code with automotive AEC-Q100 qualification in a distributor listing. RoHS addresses restricted substances in electrical equipment, while AEC-Q100 concerns automotive qualification; the two designations should be tracked independently in supplier qualification and product-release records.
Where to buy MCP603T-E/CH online and what is the current lead time?
Use the Request a Quote form on this page to request MCP603T-E/CH pricing, stock confirmation, and current lead time. The part is offered in a 6-pin SOT-23 package and is also listed in cut-tape packaging, but production quantity and delivery schedules can vary by order configuration. Providing the target quantity, date code requirement, and destination country will produce the most useful quotation response.

بيانات مرجعية هندسية لـ MCP603T-E/CH — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose MCP603T-E/CH for compact, low-power signal conditioning that benefits from a 2.8 MHz gain-bandwidth product, 4.5 V/us slew rate, low input-bias current, and operation from 2.7 V to 6.0 V. It is particularly appropriate for battery-powered sensors, portable audio paths, process-sensor interfaces, and compact data-acquisition boards. The MCP603T-I/CH is the closest identified same-family alternative, but its different temperature-grade classification must satisfy the installation environment before substitution is accepted. For designs requiring extremely low offset, very low noise, high output current, or substantially wider bandwidth, a dedicated precision or high-performance amplifier will usually be a better architectural choice. This part is best when compactness, low quiescent current, rail-to-rail output, and moderate bandwidth are the dominant requirements.

المقارنة مع البدائل

المعامل هذا المنتج MCP603T-I/CH
Brand Microchip Technology Microchip Technology
Package SOT-23-6 SOT-23-6
Amplifier Type General Purpose General Purpose
Number of Circuits 1 circuit 1 circuit

أبرز الفروقات

  • Low-power operation suitable for portable analog circuits (مقابلMCP603T-I/CH)
  • Wide operating-temperature suitability (مقابلMCP603T-I/CH)
  • Single-supply rail-to-rail output operation (مقابلMCP603T-I/CH)

ملاحظات التصميم

Place the supply-decoupling capacitor and the amplifier's ground connection as close to their SOT-23-6 pins as practical. Keep the input and feedback traces short, and route them away from switching nodes, inductors, and high-current return paths. Because the package is physically small, use the manufacturer's recommended land pattern rather than substituting a generic SOT-23 footprint, and verify solder paste volume, stencil apertures, and assembly clearance during PCB review.

Do not assume that the rail-to-rail output reaches either supply rail at every load. Check the output-voltage swing limits for the selected 2.7 V to 6.0 V supply, output load, and gain. Also verify that the input common-mode voltage remains inside the usable range at all times. If the source can float while the supply is active, add a defined bias path so that the amplifier does not operate outside its valid input region.

Estimated: with a 3.3 V supply, 3.0 V output, and 100 uA load, the amplifier's ideal pass-device loss is approximately (3.3 V - 3.0 V) × 100 uA, or 0.03 uA, before the 230 uA typical quiescent current is included. Actual battery-system consumption is therefore likely to be dominated by quiescent and external-load current. Use the shutdown control to remove the active-state contribution during idle periods and confirm the shutdown logic polarity in the system controller.

For high-impedance sensor inputs, guard the sensitive traces and keep conductive contamination, moisture, and flux residues under control because board leakage can exceed the MCP603's 1 pA input-bias current. Evaluate source impedance together with input capacitance to establish the practical input bandwidth. For ADC interfaces, place an anti-alias capacitor at the amplifier output and verify settling against the converter's acquisition time instead of relying on gain-bandwidth product alone.

معلومات الامتثال

RoHS
Compliant
REACH
Unknown
AEC-Q100
Qualified
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

RoHS compliance and automotive AEC-Q100 qualification are identified in component listings. Other environmental declarations are unknown and should be confirmed from the manufacturer's current product documentation before regulatory submission.

تم التحقق من البيانات في: 2026-11-15 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

mcp603 rehlko MCP603T-E/CH datasheet MCP603T-E/CH pinout MCP603T-E/CH datasheet pdf MCP603T-E/CH specifications MCP603T-E/CH equivalent MCP603T-E/CH replacement MCP603T-E/CH cross reference MCP603T-E/CH vs MCP603T-I/CH MCP603 SOT-23-6 footprint MCP603 low power op amp MCP603 sensor application circuit MCP603T-E/CH price MCP603T-E/CH stock

المكونات والمصطلحات ذات الصلة

Microchip Technology MCP603T-E/CH MCP603 MCP603T-I/CH operational amplifier op amp general-purpose amplifier single-supply amplifier CMOS rail-to-rail output gain-bandwidth product slew rate common-mode rejection input offset voltage input bias current input voltage noise density shutdown function SOT-23-6 surface mount SMD low-power electronics sensor signal conditioning battery-powered instrumentation AEC-Q100 RoHS
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر