MCP603T-E/CH - 2.8MHz R-R Op Amp | Microchip Technology
MPN: MCP603T-E/CH ✓ 啟用中MCP603T-E/CH 概覽
An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify, buffer, filter, or compare small analog signals. The MCP603 belongs to the CMOS operational-amplifier family and operates from a single positive supply. Its rail-to-rail output allows the output to approach the supply limits, while shutdown control can reduce power consumption when the circuit is not active.
Key characteristics include a 2.8 MHz gain-bandwidth product, 4.5 V/us slew rate, 29 nV/sqrt(Hz) input noise at 1 kHz, and less than 2 mV typical offset voltage. The typical operating current of 230 uA supports battery-powered and portable systems, while the 2.7 V minimum supply voltage enables operation from low-voltage rails.
The MCP603 uses Microchip's advanced CMOS technology to provide low bias current and low power consumption in a compact surface-mount package. Reported input-bias current is 1 pA, input-offset current is 20 pA, and the device provides approximately 106 dB common-mode rejection. These characteristics are useful when the op amp must process high-impedance sensor signals without loading the source.
Typical applications include low-power sensor signal conditioning, battery-operated instrumentation, audio input stages, portable measurement systems, and general-purpose analog filtering. The shutdown function is valuable in duty-cycled systems because it allows the amplifier to be disabled when measurements are not required.
Designers should account for the 2.7 V minimum supply voltage and confirm that the selected operating point satisfies the amplifier's common-mode and output-swing requirements. Decoupling capacitors should be placed close to the supply pins, and unused inputs must be biased so the amplifier remains in a defined state. The SOT-23-6 footprint requires careful land-pattern compliance and adequate assembly clearance.
This product record combines the manufacturer specifications, package identification, operating characteristics, application guidance, and substitution analysis needed to evaluate the MCP603T-E/CH before PCB implementation or procurement.
直接替換替代品,適用於 MCP603T-E/CH — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MCP603T-I/CH
✅ 直接替換📋 參考替代品(不在目錄中)
MCP603T-E/CH 最大額定值與電氣特性
| Amplifier Type | General Purpose |
| Number of Circuits | 1 circuit |
| Supply Voltage Range | 2.7 V to 6.0 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Slew Rate | 4.5 V/us |
| Typical Operating Current | 230 uA |
| Input Offset Voltage | 1 mV maximum; less than 2 mV typical |
| Input Bias Current | 1 pA |
| Input Offset Current | 20 pA |
| Input Voltage Noise Density | 29 nV/sqrt(Hz) at 1 kHz |
| Common-Mode Rejection | 106 dB |
| Input Offset Voltage Drift | 2.5 uV/C |
| 工作溫度範圍 | -40 C to +125 C |
| 輸出類型 | Rail-to-Rail |
| Shutdown Function | Enabled |
| ESD Protection | Enabled |
| 封裝 | SOT-23-6 |
| Packaging | Cut Tape |
| RoHS 狀態 | Compliant |
| Automotive Qualification | AEC-Q100 |
MCP603T-E/CH sot-23-6 腳位配置指南
MCP603T-E/CH(sot-23-6 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP603T-E/CH.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP603T-E/CH 適用於 6 應用s: Battery-Powered Sensor Conditioning, Portable Medical Signal Conditioning, Low-Power Audio Input Amplifier, Industrial Process Signal Amplifier, Portable Data Acquisition, Active Filtering and Buffering.
Battery-Powered Sensor Conditioning
The MCP603T-E/CH fits low-energy sensor front ends because its 230 uA typical operating current and 1 pA input-bias current reduce loading on battery-powered sources. Its 29 nV/sqrt(Hz) input noise at 1 kHz, less than 2 mV typical offset voltage, and 106 dB common-mode rejection support measurement of small changes superimposed on larger bias voltages. The amplifier can amplify a bridge, resistive, or current-based sensor output, although the selected circuit must keep the signal within the input common-mode range. Use the shutdown function between measurement intervals to reduce consumption when continuous amplification is unnecessary.
推薦
Portable Medical Signal Conditioning
The MCP603T-E/CH can serve as the gain stage in compact medical monitoring equipment when the design prioritizes low power and a small footprint. Its 2.8 MHz gain-bandwidth product is suitable for signals in the audio and low-frequency physiological range, while the 106 dB common-mode rejection helps suppress interference coupled into high-impedance electrodes or sensor leads. The 1 pA input-bias current is valuable when source impedance is high. Designers must still assess patient-safety isolation, input protection, diagnostic accuracy, and applicable medical validation requirements; the amplifier qualification alone does not establish compliance for the finished instrument.
推薦
Low-Power Audio Input Amplifier
The MCP603T-E/CH is suitable for buffering low-level audio inputs in portable equipment because its rail-to-rail output and 4.5 V/us slew rate can reproduce small signals while operating from a 2.7 V to 6.0 V supply. The 2.8 MHz gain-bandwidth product provides useful bandwidth for audio-band amplification, and 230 uA typical operating current supports long battery life. In headphone, microphone, or auxiliary-input circuits, the output-load capability and distortion behavior should be checked at the selected voltage gain. Input and output filtering should target the intended audio bandwidth rather than unnecessarily amplifying noise outside it.
推薦
Industrial Process Signal Amplifier
The MCP603T-E/CH can condition low-level process signals in industrial control boards when the signal bandwidth is modest and the operating environment is extended. Its -40 C to +125 C temperature range supports demanding ambient conditions, while 106 dB common-mode rejection reduces the effect of common-mode noise on sensor lines. The 2.8 MHz closed-loop bandwidth and 4.5 V/us slew rate are adequate for many pressure, temperature, and position interfaces. Engineers should add appropriate input protection, verify the common-mode range at the actual supply voltage, and evaluate electromagnetic interference requirements at the board and enclosure level.
推薦
Portable Data Acquisition
The MCP603T-E/CH is appropriate for a compact data-acquisition front end that converts a low-amplitude analog measurement into a voltage suitable for an ADC. Its 2.8 MHz gain-bandwidth product supports moderate closed-loop bandwidth, while its 29 nV/sqrt(Hz) input-noise density contributes relatively little noise in many sensor signals. The 1 pA bias current minimizes disturbance of high-impedance sources, and the shutdown function can support periodic sampling systems. Select the external gain carefully to preserve stability, include an anti-alias filter before the converter, and ensure that the amplifier can charge the ADC sample-and-hold input within the acquisition interval.
推薦
Active Filtering and Buffering
The MCP603T-E/CH can implement active low-pass, high-pass, or general biquad filter sections when a compact, low-power implementation is required. Its 2.8 MHz gain-bandwidth product provides useful closed-loop bandwidth for filters handling low-frequency or audio-range signals, while the 4.5 V/us slew rate helps preserve amplitude through rapidly varying waveforms. Component tolerances around the feedback network directly affect cutoff frequency and Q, so standard resistor and capacitor tolerances should be evaluated against the filter response. The rail-to-rail output improves usable signal range in single-supply circuits, but headroom limitations at high frequency and load must be checked using the manufacturer data.
推薦
推薦產品摘要
工程參考資料,適用於 MCP603T-E/CH — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP603T-I/CH |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | SOT-23-6 | SOT-23-6 |
| Amplifier Type | General Purpose | General Purpose |
| Number of Circuits | 1 circuit | 1 circuit |
主要差異化特點
- Low-power operation suitable for portable analog circuits (對比MCP603T-I/CH)
- Wide operating-temperature suitability (對比MCP603T-I/CH)
- Single-supply rail-to-rail output operation (對比MCP603T-I/CH)
設計說明
Place the supply-decoupling capacitor and the amplifier's ground connection as close to their SOT-23-6 pins as practical. Keep the input and feedback traces short, and route them away from switching nodes, inductors, and high-current return paths. Because the package is physically small, use the manufacturer's recommended land pattern rather than substituting a generic SOT-23 footprint, and verify solder paste volume, stencil apertures, and assembly clearance during PCB review.
Do not assume that the rail-to-rail output reaches either supply rail at every load. Check the output-voltage swing limits for the selected 2.7 V to 6.0 V supply, output load, and gain. Also verify that the input common-mode voltage remains inside the usable range at all times. If the source can float while the supply is active, add a defined bias path so that the amplifier does not operate outside its valid input region.
Estimated: with a 3.3 V supply, 3.0 V output, and 100 uA load, the amplifier's ideal pass-device loss is approximately (3.3 V - 3.0 V) × 100 uA, or 0.03 uA, before the 230 uA typical quiescent current is included. Actual battery-system consumption is therefore likely to be dominated by quiescent and external-load current. Use the shutdown control to remove the active-state contribution during idle periods and confirm the shutdown logic polarity in the system controller.
For high-impedance sensor inputs, guard the sensitive traces and keep conductive contamination, moisture, and flux residues under control because board leakage can exceed the MCP603's 1 pA input-bias current. Evaluate source impedance together with input capacitance to establish the practical input bandwidth. For ADC interfaces, place an anti-alias capacitor at the amplifier output and verify settling against the converter's acquisition time instead of relying on gain-bandwidth product alone.
合規資訊
RoHS compliance and automotive AEC-Q100 qualification are identified in component listings. Other environmental declarations are unknown and should be confirmed from the manufacturer's current product documentation before regulatory submission.