Microchip Technology

MCP6041-I/SN - 600 nA, 14 kHz, Rail-to-Rail Op Amp | Microchip Technology

MPN: MCP6041-I/SN ✓ نشط
1.4 V Vdss 600 nA Id 8-pin SOIC Package
الحد الأدنى للطلب: 1 |

MCP6041-I/SN نظرة عامة

Microchip Technology MCP6041-I/SN is a single-amplifier CMOS operational amplifier with a 14 kHz gain-bandwidth product, 600 nA typical operating current, and rail-to-rail input and output operation in an 8-pin SOIC package. It operates from a single supply as low as 1.4 V and is designed for portable, battery-powered, instrumentation, and low-frequency signal-conditioning systems.

An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives an output according to that difference. When used with negative feedback, it can amplify, buffer, filter, or condition analog signals. In the component hierarchy, the MCP6041-I/SN is a CMOS operational amplifier, a general-purpose amplifier IC, and a low-power analog semiconductor intended for precision signal paths.

The MCP6041 family combines rail-to-rail input and output capability with low quiescent current. The manufacturer identifies a typical operating current of 600 nA and an input offset voltage below 3 mV. Its 14 kHz gain-bandwidth product supports low-frequency applications, while unity-gain stability simplifies buffer and amplifier configurations. Maximum quiescent current is less than 1 µA per amplifier according to the manufacturer datasheet.

Microchip implements the device using advanced CMOS technology. This process supports low bias current, high open-loop gain, rail-to-rail output swing, and low power consumption. The result is an amplifier that can operate from a low-voltage supply while accepting input signals that extend across the supply rails. Its low bandwidth makes it more appropriate for instrumentation and sensor conditioning than for high-speed signal processing.

Typical uses include low-frequency sensor amplifiers, portable measurement systems, battery-operated instrumentation, audio and communications interface buffering, and precision voltage conditioning. The rail-to-rail input stage is useful when signals may approach either supply rail, while the rail-to-rail output stage provides a wide output swing for low-voltage analog systems.

For proper operation, verify the input common-mode range, output swing, and load requirements against the system supply voltage. Keep input and feedback traces short, provide a stable bypass connection near the supply pin, and account for the very low bandwidth when selecting compensation or filter components. The 8-pin SOIC package simplifies assembly and provides adequate spacing for hand-soldered prototypes.

This product page combines manufacturer specifications, sourcing guidance, same-package drop-in options, application engineering notes, and a parameter comparison so designers can evaluate the MCP6041-I/SN before integrating a micropower rail-to-rail amplifier into low-voltage analog systems.

بدائل مباشرة لـ MCP6041-I/SN — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

MCP6041-E/SN

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin SOIC
Same 14 kHz gain-bandwidth product and 600 nA typical operating current; temperature-grade suffix differs from -I to -E

📋 بديل مرجعي (غير موجود في الكتالوج)

MCP6041-I/SS

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin SOIC
Same 14 kHz gain-bandwidth product, 600 nA typical current, and 8-pin SOIC footprint; package-ordering suffix differs from SN to SS

📋 بديل مرجعي (غير موجود في الكتالوج)

MCP6041-E/SS

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin SOIC
Same 14 kHz gain-bandwidth product and 600 nA typical operating current; -E temperature grade and SS ordering suffix differ from -I/SN

📋 بديل مرجعي (غير موجود في الكتالوج)

MCP6041-I/SN الحدود القصوى والخصائص الكهربائية

Amplifier Type General-purpose operational amplifier
Number of Circuits 1 amplifier
Gain-Bandwidth Product 14 kHz
Typical Operating Current 600 nA
Maximum Quiescent Current Less than 1 µA per amplifier
Minimum Single-Supply Voltage 1.4 V
Input Offset Voltage Less than 3 mV typical
Output Swing Rail-to-rail output
Input Type Rail-to-rail input
Technology CMOS
Unity-Gain Stability Unity-gain stable
العلبة 8-pin SOIC
نوع التركيب Surface mount

تكوين أطراف MCP6041-I/SN

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
دبوس 1 NC — Not connected
دبوس 2 IN- — Inverting input
دبوس 3 IN+ — Non-inverting input
دبوس 4 V- — Negative supply or ground connection
دبوس 5 V+ — Positive supply connection
دبوس 6 OUT — Analog output
دبوس 7 V+ — Positive supply connection
دبوس 8 V- — Negative supply or ground connection

التطبيقات النموذجية

MCP6041-I/SN مناسب لـ 6 التطبيقs: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Frequency Precision Buffering, Industrial Process Signal Interface, Audio and Communications Interface Buffering, Low-Voltage Reference and Feedback Buffer.

🧩

Battery-Powered Sensor Conditioning

The MCP6041-I/SN is well suited to conditioning signals from low-power sensors because it operates from a single supply as low as 1.4 V while drawing only 600 nA typical operating current. Its rail-to-rail input stage helps retain usable input range as the battery voltage falls, and the rail-to-rail output provides a wide swing for driving the next analog stage. The 14 kHz gain-bandwidth product is appropriate for temperature, pressure, and slow position sensors rather than high-bandwidth signals. Place the bypass capacitor close to V+ and use the non-inverting input for the sensor when a simple gain stage is required.

📱

Portable Measurement Instrumentation

The MCP6041-I/SN supports portable instruments where battery life and signal range are more important than high bandwidth. Its sub-microamp maximum quiescent current limits the standing load imposed by the amplifier, while the 1.4 V minimum single-supply capability supports low-voltage sensing systems. Rail-to-rail input and output operation improves utilization of the available supply range. The 14 kHz bandwidth is suitable for slowly varying measurement channels, and unity-gain stability allows the device to be used directly as a buffer. Select external resistors carefully when gain accuracy is important.

🔧

Low-Frequency Precision Buffering

MCP6041-I/SN can buffer high-impedance sources because its CMOS implementation provides low bias current and the manufacturer highlights high open-loop gain. The unity-gain-stable configuration simplifies direct buffering without a complex compensation network, and the input offset voltage is specified below 3 mV typical. With a 14 kHz gain-bandwidth product, the amplifier is intended for low-frequency precision paths such as sensor outputs, reference nodes, and slowly changing instrumentation signals. Keep the buffer input and output routing short to minimize added error and susceptibility to leakage.

🏭

Industrial Process Signal Interface

The MCP6041-I/SN can condition low-frequency industrial process signals when the signal bandwidth remains well below the device's 14 kHz gain-bandwidth product. Its industrial ordering grade is appropriate for systems requiring the associated temperature-range designation, while low quiescent current helps control auxiliary power in distributed measurement nodes. Rail-to-rail input and output behavior is useful with low-voltage sensor front ends. The design should still account for common-mode limits, output swing, noise, and the protection required at external interface connectors.

🌐

Audio and Communications Interface Buffering

The MCP6041-I/SN is appropriate for buffering low-frequency audio-control or communications-interface nodes when a very low supply current is the main requirement. Rail-to-rail input and output operation allows signals to use most of a low-voltage supply range, and the unity-gain-stable amplifier can isolate a high-impedance source from the following stage. Its 14 kHz bandwidth is adequate for low-frequency control paths but not for high-fidelity audio passbands, so it should be used for auxiliary or control signals rather than a main audio amplifier. Add stable decoupling at the supply pin.

⚡

Low-Voltage Reference and Feedback Buffer

MCP6041-I/SN can serve as a low-power buffer for reference nodes, feedback elements, and precision divider outputs. Its CMOS bias characteristics reduce disturbance to high-impedance sources, while the manufacturer identifies a typical operating current of 600 nA and an offset voltage below 3 mV. These characteristics make it useful in low-voltage analog systems where every microamp contributes to the power budget. Because the 14 kHz bandwidth is modest, avoid using it where the required settling time or loop dynamics demand greater bandwidth.

ملخص المنتجات الموصى بها

What are the key specifications of MCP6041-I/SN that engineers should know?
The MCP6041-I/SN is a single, unity-gain-stable CMOS op amp with a 14 kHz gain-bandwidth product, 600 nA typical operating current, rail-to-rail input and output operation, and operation from a single supply as low as 1.4 V. According to the Microchip manufacturer datasheet 20001669e, maximum quiescent current is less than 1 µA per amplifier. These characteristics make the device suitable for battery-powered sensing, buffering, and low-frequency analog conditioning.
What is the operating voltage range of MCP6041-I/SN?
The MCP6041-I/SN operates from a single supply as low as 1.4 V and is designed for rail-to-rail input and output operation. The manufacturer also describes rail-to-rail output swing and advanced CMOS technology in datasheet 20001669e. The complete maximum supply voltage and operating temperature limits are not printed in the product excerpts, so confirm those limits in the complete Microchip datasheet before finalizing a design.
What is the output noise and offset voltage of MCP6041-I/SN?
The Microchip product page specifies an input offset voltage below 3 mV for the MCP6041, but it does not state a complete output-noise spectrum in the product summary. Input offset and noise behavior are especially important for low-frequency instrumentation because they influence DC accuracy and the smallest resolvable signal. Use the noise and offset tables in manufacturer datasheet 20001669e for configuration-specific values.
Is MCP6041-I/SN suitable for battery-powered sensor applications?
Yes, the MCP6041-I/SN is suitable for battery-powered sensor conditioning because it draws 600 nA typical operating current and has a maximum quiescent current below 1 µA per amplifier. Its rail-to-rail input and output capability also helps preserve signal range on low-voltage supplies. The Microchip manufacturer datasheet 20001669e specifically identifies battery-powered and portable applications as supported use cases.
What can replace MCP6041-I/SN on the same 8-pin SOIC footprint?
MCP6041-E/SN, MCP6041-I/SS, and MCP6041-E/SS are same-family Microchip options associated with the same 8-pin SOIC format and closely matched electrical architecture. The primary selection points are operating-temperature grade and temperature-range suffix. Confirm the exact ordering code, pinout, and electrical limits against the Microchip datasheet before treating any of these parts as a production replacement.
Is MCP6041-I/SN the same as MCP6041-E/SN?
MCP6041-I/SN and MCP6041-E/SN use the same 8-pin SOIC package and belong to the same low-power rail-to-rail amplifier family, but their ordering suffixes identify different temperature grades. The electrical core is closely matched, while the authorized operating-temperature range differs. Select the grade required by the product's environmental requirements and verify the limits in the manufacturer datasheet before substitution.
When should I choose MCP6041-I/SN over MCP6041-E/SN?
Choose MCP6041-I/SN when the application requires the industrial-grade ordering option rather than the extended-temperature MCP6041-E/SN option. Both parts use the 8-pin SOIC package and share the same 14 kHz-class, micropower, rail-to-rail amplifier architecture. The decision should follow the required ambient-temperature range and qualification constraints rather than a change in PCB footprint.
MCP6041-I/SN vs MCP6567-E/SN: which is better for a low-power design?
MCP6041-I/SN is the stronger choice when minimum power consumption is the priority because its typical operating current is 600 nA and its gain-bandwidth product is 14 kHz. MCP6567-E/SN provides substantially greater bandwidth, but the comparison data identifies different noise characteristics and a much higher operating speed. Use MCP6041-I/SN for very-low-frequency precision buffering and select MCP6567-E/SN when signal speed is more important than nanoamp-level supply current.
Where can I download the MCP6041-I/SN datasheet PDF?
The official Microchip manufacturer datasheet is available as the PDF document 20001669e at the Microchip download link listed on this page. It covers the MCP6041/2/3/4 family and describes the single-supply operation from 1.4 V, sub-microamp quiescent current, rail-to-rail input and output capability, and low-frequency application characteristics. Use that document for the complete electrical tables, pin descriptions, and ordering information.
Where can I find the MCP6041-I/SN pinout?
The MCP6041-I/SN pinout is shown in the Microchip manufacturer datasheet 20001669e. This single-amplifier 8-pin SOIC uses the standard pin sequence of 1 NC, 2 inverting input, 3 non-inverting input, 4 V−, 5 V+, 6 output, 7 V+, and 8 V−. Assign PCB tracks from the package drawing and pin-description table rather than inferring connections from package shape alone.
Where can I buy MCP6041-I/SN online?
Use the Request a Quote form on this page to request MCP6041-I/SN availability, current lead time, and a quotation for the exact 8-pin SOIC ordering code. The form helps prevent accidental substitution of another MCP6041 package or temperature suffix. Current stock and lead time should be confirmed at the time of your production-planning review.
What is the price of MCP6041-I/SN?
The current commercial price for MCP6041-I/SN should be requested through the Request a Quote form on this page. Quote confirmation for the exact 8-pin SOIC ordering code is preferable to relying on a generic family price because package, temperature grade, order quantity, and supply status can change the commercial result. The form also allows a buyer to request lead time and available quantity in one request.
What is the lead time for MCP6041-I/SN?
Request the current MCP6041-I/SN lead time through the Request a Quote form on this page. Lead time depends on the confirmed order quantity, package code, production schedule, and current manufacturer channel status. For a production BOM, request the lead time for the exact MCP6041-I/SN ordering code rather than for the broader MCP6041 family.
Is MCP6041-I/SN in stock?
Current MCP6041-I/SN inventory should be confirmed through the Request a Quote form on this page. The form is the appropriate route for obtaining quantity, lead time, and commercial confirmation together. Because availability can change quickly, do not treat a general family listing as confirmation of the exact 8-pin SOIC industrial-temperature part.
What is the best Microchip equivalent for MCP6041-I/SN?
MCP6041-E/SN is the closest same-family choice for an existing 8-pin SOIC design when the required temperature grade permits it. MCP6041-I/SS and MCP6041-E/SS provide additional ordering-code options associated with the same family and package format. The best equivalent is determined by matching the footprint, pin functions, supply range, electrical limits, and required operating-temperature grade.

بيانات مرجعية هندسية لـ MCP6041-I/SN — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose MCP6041-I/SN for low-voltage, low-frequency analog systems where nanoamp-class supply current, rail-to-rail signal range, and an industrial-grade ordering option are important. Its 14 kHz gain-bandwidth product and less-than-3 mV typical offset make it appropriate for slow sensor signals, buffering, instrumentation, and reference conditioning rather than high-speed signal processing. MCP6041-E/SN is the closest same-package alternative when its extended-temperature grade better matches the system requirements. MCP6041-I/SS and MCP6041-E/SS are additional same-family 8-pin SOIC choices whose ordering and temperature combinations should be checked against the Microchip ordering table. For designs requiring substantially higher bandwidth, a different amplifier family is more appropriate; for dual- or quad-channel implementations, the MCP6042 and MCP6044 family members reduce the number of separate amplifier packages.

المقارنة مع البدائل

المعامل هذا المنتج MCP6041-E/SN MCP6041-I/SS MCP6041-E/SS
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Number of Amplifiers 1 amplifier 1 amplifier 1 amplifier 1 amplifier
Gain-Bandwidth Product 14 kHz 14 kHz 14 kHz 14 kHz
Typical Operating Current 600 nA 600 nA 600 nA 600 nA
Minimum Single-Supply Voltage 1.4 V 1.4 V 1.4 V 1.4 V
Input Offset Voltage Less than 3 mV typical Less than 3 mV typical Less than 3 mV typical Less than 3 mV typical
Input and Output Operation Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output
Technology CMOS CMOS CMOS CMOS
Operating-Temperature Grade -I industrial grade -E extended-temperature grade -I industrial grade -E extended-temperature grade

أبرز الفروقات

  • Very low typical operating current (مقابلMCP6041-E/SN)
  • Same-package family options (مقابلMCP6041-I/SS)
  • Low-voltage rail-to-rail operation (مقابلMCP6041-E/SS)

ملاحظات التصميم

Place the supply bypass capacitor directly between pins 5 and 7, which are both V+ connections, and connect pin 4 and pin 8 to the supply return. Route the bypass loop and amplifier ground connection with minimal inductance. For sensitive high-impedance inputs, keep the non-inverting and inverting traces away from the supply-capacitor return path to reduce power-supply coupling into the measured signal.

Do not treat rail-to-rail input as an unlimited input range. The manufacturer datasheet defines the valid common-mode range for each supply voltage, and inputs outside that region may cause incorrect output behavior or device damage. Similarly, rail-to-rail output swing does not mean the output reaches the supply rails under every load. Check the output-load and supply conditions in datasheet 20001669e before selecting output margins.

The 14 kHz gain-bandwidth product is appropriate for low-frequency signals but requires closed-loop-gain planning for stability and bandwidth. Unity-gain operation is supported, while higher closed-loop gains reduce usable bandwidth. Avoid capacitance on the inverting input unless it is part of a compensated filter stage, and use short feedback traces to reduce parasitic feedback and oscillation risk in sensitive analog nodes.

Estimated: with a 3.3 V supply and a 10 kΩ load, output current is approximately 0.33 mA and the amplifier's output-stage dissipation is approximately 0.33 mW, calculated from VOUT × IOUT. This estimate excludes internal bias current and does not represent the complete device power budget. Under light load, board leakage and measurement-system current may dominate, so evaluate the assembled system rather than the nominal amplifier current alone.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The MCP6041 is a general-purpose operational amplifier rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not identified in the product excerpts and require confirmation from the manufacturer product documentation.

تم التحقق من البيانات في: 2026-11-15 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

mcp6041 datasheet mcp6041 pdf MCP6041-I/SN datasheet MCP6041-I/SN pinout MCP6041-I/SN equivalent MCP6041-I/SN replacement MCP6041-I/SN drop-in replacement MCP6041-I/SN price MCP6041-I/SN stock MCP6041 600 nA op amp MCP6041 14 kHz amplifier MCP6041 rail-to-rail SOIC-8 MCP6041 battery powered sensor MCP6041-I/SN vs MCP6041-E/SN Microchip MCP6041-I/SN

المكونات والمصطلحات ذات الصلة

Microchip Technology MCP6041-I/SN MCP6041 MCP6041-E/SN MCP6041-I/SS MCP6041-E/SS MCP6041-I/MS MCP6042-I/SL MCP6044-I/SL operational amplifier op amp CMOS operational amplifier general-purpose amplifier IC analog semiconductor rail-to-rail input rail-to-rail output gain-bandwidth product quiescent current input offset voltage unity-gain stability single-supply operation battery-powered instrumentation sensor conditioning precision buffering SOIC-8 surface-mount package
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر