MCP6041-I/SN - 600 nA, 14 kHz, Rail-to-Rail Op Amp | Microchip Technology
MPN: MCP6041-I/SN ✓ 啟用中MCP6041-I/SN 概覽
An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives an output according to that difference. When used with negative feedback, it can amplify, buffer, filter, or condition analog signals. In the component hierarchy, the MCP6041-I/SN is a CMOS operational amplifier, a general-purpose amplifier IC, and a low-power analog semiconductor intended for precision signal paths.
The MCP6041 family combines rail-to-rail input and output capability with low quiescent current. The manufacturer identifies a typical operating current of 600 nA and an input offset voltage below 3 mV. Its 14 kHz gain-bandwidth product supports low-frequency applications, while unity-gain stability simplifies buffer and amplifier configurations. Maximum quiescent current is less than 1 µA per amplifier according to the manufacturer datasheet.
Microchip implements the device using advanced CMOS technology. This process supports low bias current, high open-loop gain, rail-to-rail output swing, and low power consumption. The result is an amplifier that can operate from a low-voltage supply while accepting input signals that extend across the supply rails. Its low bandwidth makes it more appropriate for instrumentation and sensor conditioning than for high-speed signal processing.
Typical uses include low-frequency sensor amplifiers, portable measurement systems, battery-operated instrumentation, audio and communications interface buffering, and precision voltage conditioning. The rail-to-rail input stage is useful when signals may approach either supply rail, while the rail-to-rail output stage provides a wide output swing for low-voltage analog systems.
For proper operation, verify the input common-mode range, output swing, and load requirements against the system supply voltage. Keep input and feedback traces short, provide a stable bypass connection near the supply pin, and account for the very low bandwidth when selecting compensation or filter components. The 8-pin SOIC package simplifies assembly and provides adequate spacing for hand-soldered prototypes.
This product page combines manufacturer specifications, sourcing guidance, same-package drop-in options, application engineering notes, and a parameter comparison so designers can evaluate the MCP6041-I/SN before integrating a micropower rail-to-rail amplifier into low-voltage analog systems.
直接替換替代品,適用於 MCP6041-I/SN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MCP6041-E/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6041-I/SS
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6041-E/SS
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6041-I/SN 最大額定值與電氣特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 1 amplifier |
| Gain-Bandwidth Product | 14 kHz |
| Typical Operating Current | 600 nA |
| Maximum Quiescent Current | Less than 1 µA per amplifier |
| Minimum Single-Supply Voltage | 1.4 V |
| Input Offset Voltage | Less than 3 mV typical |
| Output Swing | Rail-to-rail output |
| Input Type | Rail-to-rail input |
| Technology | CMOS |
| Unity-Gain Stability | Unity-gain stable |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
MCP6041-I/SN 腳位配置
| 腳位 1 | NC — Not connected |
| 腳位 2 | IN- — Inverting input |
| 腳位 3 | IN+ — Non-inverting input |
| 腳位 4 | V- — Negative supply or ground connection |
| 腳位 5 | V+ — Positive supply connection |
| 腳位 6 | OUT — Analog output |
| 腳位 7 | V+ — Positive supply connection |
| 腳位 8 | V- — Negative supply or ground connection |
典型應用
MCP6041-I/SN 適用於 6 應用s: Battery-Powered Sensor Conditioning, Portable Measurement Instrumentation, Low-Frequency Precision Buffering, Industrial Process Signal Interface, Audio and Communications Interface Buffering, Low-Voltage Reference and Feedback Buffer.
Battery-Powered Sensor Conditioning
The MCP6041-I/SN is well suited to conditioning signals from low-power sensors because it operates from a single supply as low as 1.4 V while drawing only 600 nA typical operating current. Its rail-to-rail input stage helps retain usable input range as the battery voltage falls, and the rail-to-rail output provides a wide swing for driving the next analog stage. The 14 kHz gain-bandwidth product is appropriate for temperature, pressure, and slow position sensors rather than high-bandwidth signals. Place the bypass capacitor close to V+ and use the non-inverting input for the sensor when a simple gain stage is required.
推薦
Portable Measurement Instrumentation
The MCP6041-I/SN supports portable instruments where battery life and signal range are more important than high bandwidth. Its sub-microamp maximum quiescent current limits the standing load imposed by the amplifier, while the 1.4 V minimum single-supply capability supports low-voltage sensing systems. Rail-to-rail input and output operation improves utilization of the available supply range. The 14 kHz bandwidth is suitable for slowly varying measurement channels, and unity-gain stability allows the device to be used directly as a buffer. Select external resistors carefully when gain accuracy is important.
推薦
Low-Frequency Precision Buffering
MCP6041-I/SN can buffer high-impedance sources because its CMOS implementation provides low bias current and the manufacturer highlights high open-loop gain. The unity-gain-stable configuration simplifies direct buffering without a complex compensation network, and the input offset voltage is specified below 3 mV typical. With a 14 kHz gain-bandwidth product, the amplifier is intended for low-frequency precision paths such as sensor outputs, reference nodes, and slowly changing instrumentation signals. Keep the buffer input and output routing short to minimize added error and susceptibility to leakage.
推薦
Industrial Process Signal Interface
The MCP6041-I/SN can condition low-frequency industrial process signals when the signal bandwidth remains well below the device's 14 kHz gain-bandwidth product. Its industrial ordering grade is appropriate for systems requiring the associated temperature-range designation, while low quiescent current helps control auxiliary power in distributed measurement nodes. Rail-to-rail input and output behavior is useful with low-voltage sensor front ends. The design should still account for common-mode limits, output swing, noise, and the protection required at external interface connectors.
推薦
Audio and Communications Interface Buffering
The MCP6041-I/SN is appropriate for buffering low-frequency audio-control or communications-interface nodes when a very low supply current is the main requirement. Rail-to-rail input and output operation allows signals to use most of a low-voltage supply range, and the unity-gain-stable amplifier can isolate a high-impedance source from the following stage. Its 14 kHz bandwidth is adequate for low-frequency control paths but not for high-fidelity audio passbands, so it should be used for auxiliary or control signals rather than a main audio amplifier. Add stable decoupling at the supply pin.
推薦
Low-Voltage Reference and Feedback Buffer
MCP6041-I/SN can serve as a low-power buffer for reference nodes, feedback elements, and precision divider outputs. Its CMOS bias characteristics reduce disturbance to high-impedance sources, while the manufacturer identifies a typical operating current of 600 nA and an offset voltage below 3 mV. These characteristics make it useful in low-voltage analog systems where every microamp contributes to the power budget. Because the 14 kHz bandwidth is modest, avoid using it where the required settling time or loop dynamics demand greater bandwidth.
推薦
推薦產品摘要
工程參考資料,適用於 MCP6041-I/SN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP6041-E/SN | MCP6041-I/SS | MCP6041-E/SS |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Amplifiers | 1 amplifier | 1 amplifier | 1 amplifier | 1 amplifier |
| Gain-Bandwidth Product | 14 kHz | 14 kHz | 14 kHz | 14 kHz |
| Typical Operating Current | 600 nA | 600 nA | 600 nA | 600 nA |
| Minimum Single-Supply Voltage | 1.4 V | 1.4 V | 1.4 V | 1.4 V |
| Input Offset Voltage | Less than 3 mV typical | Less than 3 mV typical | Less than 3 mV typical | Less than 3 mV typical |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Technology | CMOS | CMOS | CMOS | CMOS |
| Operating-Temperature Grade | -I industrial grade | -E extended-temperature grade | -I industrial grade | -E extended-temperature grade |
主要差異化特點
- Very low typical operating current (對比MCP6041-E/SN)
- Same-package family options (對比MCP6041-I/SS)
- Low-voltage rail-to-rail operation (對比MCP6041-E/SS)
設計說明
Place the supply bypass capacitor directly between pins 5 and 7, which are both V+ connections, and connect pin 4 and pin 8 to the supply return. Route the bypass loop and amplifier ground connection with minimal inductance. For sensitive high-impedance inputs, keep the non-inverting and inverting traces away from the supply-capacitor return path to reduce power-supply coupling into the measured signal.
Do not treat rail-to-rail input as an unlimited input range. The manufacturer datasheet defines the valid common-mode range for each supply voltage, and inputs outside that region may cause incorrect output behavior or device damage. Similarly, rail-to-rail output swing does not mean the output reaches the supply rails under every load. Check the output-load and supply conditions in datasheet 20001669e before selecting output margins.
The 14 kHz gain-bandwidth product is appropriate for low-frequency signals but requires closed-loop-gain planning for stability and bandwidth. Unity-gain operation is supported, while higher closed-loop gains reduce usable bandwidth. Avoid capacitance on the inverting input unless it is part of a compensated filter stage, and use short feedback traces to reduce parasitic feedback and oscillation risk in sensitive analog nodes.
Estimated: with a 3.3 V supply and a 10 kΩ load, output current is approximately 0.33 mA and the amplifier's output-stage dissipation is approximately 0.33 mW, calculated from VOUT × IOUT. This estimate excludes internal bias current and does not represent the complete device power budget. Under light load, board leakage and measurement-system current may dominate, so evaluate the assembled system rather than the nominal amplifier current alone.
合規資訊
The MCP6041 is a general-purpose operational amplifier rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not identified in the product excerpts and require confirmation from the manufacturer product documentation.