Texas Instruments

OPA172ID - 36V, 10MHz Rail-to-Rail Op Amp | Texas Instruments

MPN: OPA172ID ✓ نشط
36 V Vdss ±8 pA Id 8-pin SOIC Package
الحد الأدنى للطلب: 1 |

OPA172ID نظرة عامة

The Texas Instruments OPA172ID is a single, 36 V, 10 MHz, low-power, rail-to-rail operational amplifier with rail-to-rail output in an 8-pin SOIC package. It supports a +4.5 V to +36 V supply range, equivalent to ±2.25 V to ±18 V, and combines a low 7 nV/√Hz noise density with a low input bias current of ±8 pA. These characteristics make it suitable for precision signal-chain and industrial measurement systems requiring low-noise amplification from relatively high-voltage supplies.

An operational amplifier, commonly called an op amp, is a high-gain differential-input active device used to amplify voltage differences. The OPA172 belongs to the high-voltage CMOS operational-amplifier family, combining an amplifier core, input protection, bias compensation, and output-stage drive in one package. Its rail-to-rail output can approach the supply rails, improving output swing in single-supply systems where conventional amplifier designs may leave less usable voltage range.

The OPA172ID provides a gain-bandwidth product of 10 MHz and an input offset voltage of ±0.2 mV. Input offset drift is limited to ±0.3 μV/°C, helping maintain accuracy as operating temperature changes. Quiescent current is 1.6 mA per amplifier, while the low input bias current supports high-impedance sources. The 7 nV/√Hz input-noise specification is particularly useful when the amplifier must preserve small signals rather than add substantial broadband noise.

Operation from a single +4.5 V supply or from split supplies up to ±18 V gives designers flexibility around industrial, instrumentation, audio, and control circuits. Rail-to-rail output behavior supports low-voltage signal conditioning without requiring a separate negative supply. Designers should still verify output swing under load, input common-mode range, stability with the selected feedback network, and the absolute maximum input-current limit of 10 mA described in the manufacturer datasheet.

Typical uses include sensor-signal conditioning, current-loop interfaces, precision buffers, audio output stages, industrial acquisition systems, and low-noise analog measurement chains. The single-amplifier configuration in the 8-pin SOIC package also simplifies designs that need one high-voltage amplifier rather than a dual or quad device. The low bias current is useful when the source impedance is high enough that input leakage would otherwise create a meaningful voltage error.

A practical design should begin with the manufacturer datasheet pin configuration and typical application circuits. Keep sensitive input and feedback routes short, provide stable decoupling close to the supply pins, and verify amplifier stability for the intended capacitive loading. Avoid allowing input voltage to exceed the supply rails because excess input current can flow during abnormal operating conditions, and keep the input current below the recommended 10 mA limit.

This page combines the OPA172ID operating limits, package details, application guidance, drop-in alternatives, and engineering trade-offs into one practical reference for high-voltage analog design. It also distinguishes direct pin-compatible choices from related family members so that replacement decisions are based on voltage range, bandwidth, noise, bias current, and output capability rather than package similarity alone.

بدائل مباشرة لـ OPA172ID — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع OPA172ID (نفس عامل الشكل والبصمة) — يختلف في Input Bias Current, Input Offset Voltage, Input Offset Voltage Drift.

Texas Instruments
Input Bias Current: ±5 pA
Input Offset Voltage: ±5 µV typical
Input Offset Voltage Drift: ±0.2 µV/°C typical
قارن مع OPA172ID →

OPA171ID

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin SOIC
Same single-amplifier 8-pin SOIC footprint; OPA171 is a related family member with different bandwidth and dynamic-performance limits.

📋 بديل مرجعي (غير موجود في الكتالوج)

OPA170ID

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin SOIC
Same single-amplifier 8-pin SOIC footprint; OPA170 is a related family member whose bandwidth and noise trade-offs differ from OPA172.

📋 بديل مرجعي (غير موجود في الكتالوج)

OPA192ID

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
Texas Instruments
📦 8-pin SOIC
Single-channel precision operational amplifier · 36 V · ±5 µV typical · ±0.2 µV/°C typical · 5.5 nV/√Hz at 1 kHz · 140 dB · ±5 pA · 10 MHz

تواصل لمعرفة السعر

عرض ورقة البيانات ←

OPA197ID

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
Texas Instruments
📦 8-pin SOIC
Single operational amplifier · 36 V · Rail-to-rail · Rail-to-rail · ±25 µV typical · ±0.25 µV/°C typical · 10 MHz · 1 channel

تواصل لمعرفة السعر

عرض ورقة البيانات ←

OPA992ID

✅ بديل مباشر
📦 8-pin SOIC
Supply range is 2.7 V to 40 V versus 4.5 V to 36 V, gain-bandwidth product is 10.6 MHz versus 10 MHz, and slew rate is 32 V/μs versus the OPA172 value.

📋 بديل مرجعي (غير موجود في الكتالوج)

OPA172ID الحدود القصوى والخصائص الكهربائية

Amplifier Type Single operational amplifier
Number of Channels 1 channel
Maximum Supply Voltage 36 V
Minimum Supply Voltage 4.5 V
Dual-Supply Operating Range ±2.25 V to ±18 V
Gain-Bandwidth Product 10 MHz
Input Offset Voltage ±0.2 mV
Input Offset Voltage Drift ±0.3 μV/°C
Input Bias Current ±8 pA
Input Noise Density 7 nV/√Hz
تيار السكون 1.6 mA per amplifier
Output Topology Rail-to-rail output
Recommended Input Current Limit 10 mA maximum
العلبة 8-pin SOIC
نوع التركيب Surface mount

تكوين أطراف OPA172ID

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
دبوس 1 OUT — Amplifier output
دبوس 2 V- — Negative supply connection
دبوس 3 +IN — Non-inverting input
دبوس 4 V- — Negative supply connection
دبوس 5 -IN — Inverting input
دبوس 6 +IN — Non-inverting input
دبوس 7 OUT — Amplifier output
دبوس 8 V+ — Positive supply connection

التطبيقات النموذجية

OPA172ID مناسب لـ 6 التطبيقs: High-Impedance Sensor Signal Conditioning, Industrial Current-Loop Interface, Precision Audio Buffer, Precision Voltage Buffer, Test and Measurement Front End, Low-Power Embedded Control Signal Chain.

🧩

High-Impedance Sensor Signal Conditioning

OPA172ID fits high-impedance sensor signal conditioning because its input bias current is ±8 pA and input-noise density is 7 nV/√Hz. These characteristics reduce source-loading errors and preserve small signals from resistive sensors, photodiode-related circuits, and high-resistance dividers. The 10 MHz gain-bandwidth product supports moderate-bandwidth amplification rather than only static measurements. Use a non-inverting or differential stage around the amplifier, maintain short feedback paths, and confirm the input common-mode range for the selected supply and gain. Because leakage from PCB contamination can dominate at picoamp input levels, clean boards and guarded input routing are as important as the device selection.

🏭

Industrial Current-Loop Interface

OPA172ID is appropriate for an industrial 4–20 mA current-loop receiver because it combines a 36 V maximum supply with a 1.6 mA quiescent current and ±8 pA input bias current. It can operate from higher-voltage industrial rails while maintaining low input-current error. The 10 MHz bandwidth allows the receiver to process both the slowly varying measurement signal and diagnostic test waveforms. A precision resistor converts the loop current into voltage, while the amplifier provides gain and filtering. Confirm input and output common-mode limits, output swing, and stability with the final feedback network across the full supply range.

🎧

Precision Audio Buffer

OPA172ID can serve as a precision audio buffer when low noise and high input impedance are more important than high-frequency slew performance. Its 7 nV/√Hz input-noise density and ±8 pA bias current reduce added noise and loading, while the 10 MHz gain-bandwidth product covers many audio-band and control-signal tasks. Rail-to-rail output helps retain useful swing from a single supply. For audio paths, verify the actual output swing into the selected load, keep the feedback loop short, and add appropriate output isolation if capacitive loads could compromise stability. The amplifier should not replace a dedicated wideband audio output stage when very low distortion at high frequency is required.

🔧

Precision Voltage Buffer

OPA172ID works well as a precision voltage buffer when the source has high impedance and the load must be isolated. A voltage follower presents very high input impedance and low output impedance, preventing the source from being loaded while retaining the measured voltage. The amplifier’s ±0.2 mV input offset, ±0.3 μV/°C offset drift, and ±8 pA bias current support accurate low-level measurements. Its 1.6 mA quiescent current also suits power-conscious instrumentation. Check the input offset and bias-current contributions against the source impedance, verify common-mode range during startup, and ensure that capacitive loading at the output remains within the stability conditions shown in the manufacturer datasheet.

📡

Test and Measurement Front End

OPA172ID can form the input stage of a test and measurement front end because it combines a 10 MHz gain-bandwidth product with low noise and very low bias current. It can amplify modest sensor outputs before a higher-bandwidth converter or digitization stage while operating from supplies up to 36 V. Its low offset voltage and offset drift help preserve accuracy as the front end gains small signals. Use the manufacturer’s typical application circuit as the starting point, place input and feedback components close to the device, and account for gain-bandwidth and closed-loop bandwidth at the selected noise-gain setting. Verify input limits before connecting external test fixtures that may exceed the supply rails.

🖥️

Low-Power Embedded Control Signal Chain

OPA172ID is suitable for embedded control and data-acquisition signal chains that require one precision amplifier rather than a multi-channel package. Its 1.6 mA quiescent current helps control system power, and the ±8 pA input bias current is valuable when conditioning high-impedance dividers or sensor outputs. The 4.5 V to 36 V supply range accommodates several industrial and automotive-system power environments. Use the amplifier in a non-inverting or differential topology, add filtering where bandwidth must be constrained, and ensure that shutdown behavior does not leave the input stage forward-biased. The 8-pin SOIC package also supports compact layouts when routing and thermal spacing permit.

ملخص المنتجات الموصى بها

OPA171ID Same-family low-noise single amplifier option يُستخدم في: High-Impedance Sensor Signal Conditioning, Precision Audio Buffer, Low-Power Embedded Control Signal Chain OPA192ID Texas Instruments يُستخدم في: High-Impedance Sensor Signal Conditioning, Precision Voltage Buffer, Low-Power Embedded Control Signal Chain OPA992ID Higher-voltage and higher-slew-rate amplifier option يُستخدم في: Industrial Current-Loop Interface, Test and Measurement Front End OPA170ID Related single-amplifier family option يُستخدم في: Industrial Current-Loop Interface, Precision Voltage Buffer OPA197ID Texas Instruments يُستخدم في: Precision Audio Buffer, Test and Measurement Front End
Where can I download the OPA172 datasheet PDF?
The OPA172 datasheet PDF is available directly from Texas Instruments at the official product page and datasheet link for the OPA172 family. The document contains the 8-pin SOIC pin configuration, electrical characteristics, recommended operating conditions, application circuits, and input-current guidance. Use the ordering-information section to confirm that OPA172ID denotes the single-amplifier SOIC package intended for an 8-pin PCB footprint.
What are the key specifications of OPA172ID that engineers should know?
OPA172ID is a single operational amplifier with a 10 MHz gain-bandwidth product, 7 nV/√Hz input-noise density, and ±8 pA input bias current. It operates from +4.5 V to +36 V, supports ±2.25 V to ±18 V split supplies, and has rail-to-rail output. Input offset voltage is ±0.2 mV, offset drift is ±0.3 μV/°C, and quiescent current is 1.6 mA per amplifier according to the Texas Instruments manufacturer datasheet.
What is the supply voltage range of OPA172ID?
OPA172ID operates from +4.5 V to +36 V in a single-supply configuration, corresponding to ±2.25 V to ±18 V when split supplies are used. This wide operating range lets the amplifier work directly from common industrial rails while still supporting lower-voltage analog systems. The Texas Instruments product page identifies the OPA172 as a 36 V single-supply operational amplifier, and the manufacturer datasheet specifies the lower 4.5 V limit.
Is OPA172ID suitable for low-noise sensor amplification?
Yes, OPA172ID is well suited to low-noise sensor amplification because its input-noise density is 7 nV/√Hz and its input bias current is only ±8 pA. The low bias current limits leakage-induced error with high-impedance sensors, while the 10 MHz gain-bandwidth product provides useful bandwidth for moderate-frequency signal chains. The manufacturer datasheet identifies these characteristics, and engineers should still calculate the total input-referred noise for the intended bandwidth.
What is the pinout of OPA172ID in the 8-pin SOIC package?
OPA172ID uses an 8-pin SOIC operational-amplifier pinout: pin 1 is OUT, pin 2 is V−, pin 3 is non-inverting input, pin 4 is V−, pin 5 is inverting input, pin 6 is non-inverting input, pin 7 is OUT, and pin 8 is V+. Use the manufacturer datasheet pin diagram when assigning PCB nets because the two output and supply assignments must match the physical orientation and package marking.
Is OPA172ID rail-to-rail input and output?
OPA172ID has a rail-to-rail output stage; the verified manufacturer description specifically identifies the device as a rail-to-rail output operational amplifier. The product listing also describes it generically as a rail-to-rail amplifier, but the detailed input common-mode limits must be checked in the manufacturer datasheet before treating the input range as fully rail-to-rail. The output topology remains suitable for maximizing swing in single-supply designs.
OPA172ID vs OPA992ID: which is better for a high-voltage amplifier?
OPA172ID offers a 10 MHz gain-bandwidth product, 7 nV/√Hz noise density, and a 1.6 mA quiescent current, making it a strong choice for low-noise signal conditioning. The Texas Instruments comparison information identifies OPA992 as offering rail-to-rail input and output, a wider 2.7 V to 40 V supply range, a 10.6 MHz gain-bandwidth product, and a 32 V/μs slew rate. Choose according to supply voltage, bandwidth, noise, and output-drive requirements rather than package alone.
When should I choose OPA172ID instead of a higher-bandwidth amplifier?
Choose OPA172ID when a 10 MHz gain-bandwidth product and 7 nV/√Hz input noise are sufficient, while low power and very low input bias current matter more than maximum slew rate. It is particularly useful for high-impedance sensors and precision buffers operating from supplies up to 36 V. For waveform shaping, large capacitive loads, or applications needing substantially more bandwidth, a higher-speed amplifier may provide better dynamic performance.
What is the best drop-in replacement for OPA172ID?
OPA172ID alternatives should be checked for an 8-pin SOIC footprint, compatible power and input pins, rail-to-rail output, and adequate voltage, noise, bias-current, and bandwidth performance. OPA171ID and OPA170ID are same-family Texas Instruments choices with related specifications, while OPA992ID offers a wider supply range and higher gain-bandwidth product. Confirm the exact pin configuration and every operating limit in the manufacturer datasheet before production substitution.
What can replace OPA172ID without changing an 8-pin SOIC PCB?
A PCB-compatible replacement must use the same 8-pin SOIC pin arrangement and remain within the target circuit’s supply, common-mode, input-current, output-swing, bandwidth, and stability limits. OPA171ID and OPA170ID are same-family candidates, while OPA192ID and OPA197ID may suit designs requiring different bandwidth or precision characteristics. OPA992ID is another high-voltage SOIC option, but a footprint match alone does not guarantee identical DC and AC behavior.
Is OPA172ID the same as OPA2172ID?
OPA172ID and OPA2172ID belong to the same OPAx172 family, but they are not the same device. OPA172ID contains one amplifier in an 8-pin SOIC package, whereas the dual OPA2172 uses two amplifier channels and its SOIC pin assignments differ. The dual version cannot replace the single amplifier without changing the PCB connections and component arrangement, despite sharing the broader family and core characteristics.
Where can I buy OPA172ID and check current availability?
Use the Request a Quote form on this page to request the current OPA172ID availability, minimum order quantity, lead time, and orderable package configuration. The listing identifies OPA172ID as an 8-SOIC, single-circuit, rail-to-rail operational amplifier from Texas Instruments. Commercial terms can change with inventory and production schedules, so request a current quotation rather than relying on a historical unit price or a cached availability statement.
What is the current price of OPA172ID?
The current commercial price of OPA172ID should be obtained through the Request a Quote form on this page. The form is the appropriate route for checking unit pricing, volume breaks, stock, and lead time for the exact OPA172ID ordering code. A cached catalog price can become stale, and the available price may depend on order quantity, delivery location, and purchasing conditions.
What is the lead time for OPA172ID?
The current lead time for OPA172ID is best requested through the Request a Quote form on this page, where the purchasing team can confirm available inventory and production scheduling. Lead time can vary with quantity, package configuration, and market conditions, so it should not be inferred from an older listing. The official Texas Instruments product and part-details pages identify OPA172ID as the orderable 8-pin SOIC configuration.
Is OPA172ID in stock?
OPA172ID availability should be confirmed through the Request a Quote form on this page because inventory and lead time change over time. The verified product listings identify the exact OPA172ID ordering code and its 8-SOIC package, allowing the quote request to be matched to the correct manufacturer part number. Requesting a quotation provides a current answer for stock, quantity breaks, and delivery expectations.

بيانات مرجعية هندسية لـ OPA172ID — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose OPA172ID for precision, low-noise signal conditioning with high-impedance sources, particularly when a single amplifier, low bias current, and operation from supplies up to 36 V are important. Its 10 MHz gain-bandwidth product, ±0.2 mV offset voltage, 7 nV/√Hz noise density, and 1.6 mA quiescent current form a balanced combination for instrumentation and industrial control. Choose OPA171ID or OPA170ID when another member of the same high-voltage family better matches the required bandwidth and noise trade-offs. Consider OPA192ID or OPA197ID for precision applications where their offset and dynamic characteristics align more closely with the target circuit. OPA992ID is attractive when operation from 2.7 V to 40 V, a 10.6 MHz gain-bandwidth product, rail-to-rail input and output, or a 32 V/μs slew rate is preferable. In every case, confirm the 8-pin SOIC pinout, supply limits, common-mode range, output swing, stability, and noise performance before approving a drop-in substitution.

المقارنة مع البدائل

المعامل هذا المنتج OPA171ID OPA170ID OPA192ID OPA197ID OPA992ID
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC

أبرز الفروقات

  • Low-noise, high-impedance amplification (مقابلOPA992ID)
  • Lower quiescent-current operating point (مقابلOPA171ID)
  • Precision offset performance for measurement chains (مقابلOPA192ID)

ملاحظات التصميم

Do not allow an input voltage to exceed the amplifier supply rails. The Texas Instruments datasheet states that excessive input current can flow as VIN rises and recommends limiting input current to 10 mA. This is especially important during shutdown, supply sequencing, and fault conditions. Add series input resistance or clamp protection where external signals can exceed the local supply range, and verify that protection-network leakage does not defeat the circuit’s low-noise or low-bias-current requirements.

Place supply-decoupling capacitors close to the V+ and V− pins and keep the feedback components adjacent to the amplifier. Sensitive input traces should be short, physically separated from switching or high-current paths, and guarded where leakage from flux residue or board contamination could approach the ±8 pA input-bias-current level. Use a continuous ground reference under the SOIC footprint where the PCB stack-up permits, and avoid routing input nets beneath noisy power stages.

Check closed-loop stability with the intended source impedance, load capacitance, and feedback network rather than assuming unity-gain stability applies everywhere. OPA172ID has a 10 MHz gain-bandwidth product, so small parasitic capacitances can alter phase margin at high closed-loop gain or during fast transients. Use the manufacturer’s typical application information to select feedback resistors and compensation values, and probe output settling when driving cables, ADC inputs, or capacitive loads.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The verified product information identifies the manufacturer, package, electrical characteristics, and ordering code but does not state the requested compliance statuses.

عمليات بحث ذات صلة

opa172 datasheet OPA172ID datasheet OPA172ID datasheet pdf OPA172ID pinout OPA172ID SOIC footprint Texas Instruments OPA172ID OPA172ID 36V 10MHz OPA172ID low noise amplifier OPA172ID equivalent OPA172ID replacement OPA172ID vs OPA992ID OPA172ID application circuit OPA172ID price OPA172ID stock

المكونات والمصطلحات ذات الصلة

Texas Instruments OPA172ID OPA171ID OPA170ID OPA192ID OPA197ID OPA992ID operational amplifier op amp single operational amplifier high-voltage CMOS operational amplifier precision amplifier rail-to-rail output amplifier 8-pin SOIC SOIC package family surface-mount package gain-bandwidth product input bias current input offset voltage input noise density quiescent current industrial signal conditioning 4–20 mA current-loop interface precision voltage buffer
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر