OPA172ID - 36V, 10MHz Rail-to-Rail Op Amp | Texas Instruments
MPN: OPA172ID ✓ AktifOPA172ID Genel Bakış
An operational amplifier, commonly called an op amp, is a high-gain differential-input active device used to amplify voltage differences. The OPA172 belongs to the high-voltage CMOS operational-amplifier family, combining an amplifier core, input protection, bias compensation, and output-stage drive in one package. Its rail-to-rail output can approach the supply rails, improving output swing in single-supply systems where conventional amplifier designs may leave less usable voltage range.
The OPA172ID provides a gain-bandwidth product of 10 MHz and an input offset voltage of ±0.2 mV. Input offset drift is limited to ±0.3 μV/°C, helping maintain accuracy as operating temperature changes. Quiescent current is 1.6 mA per amplifier, while the low input bias current supports high-impedance sources. The 7 nV/√Hz input-noise specification is particularly useful when the amplifier must preserve small signals rather than add substantial broadband noise.
Operation from a single +4.5 V supply or from split supplies up to ±18 V gives designers flexibility around industrial, instrumentation, audio, and control circuits. Rail-to-rail output behavior supports low-voltage signal conditioning without requiring a separate negative supply. Designers should still verify output swing under load, input common-mode range, stability with the selected feedback network, and the absolute maximum input-current limit of 10 mA described in the manufacturer datasheet.
Typical uses include sensor-signal conditioning, current-loop interfaces, precision buffers, audio output stages, industrial acquisition systems, and low-noise analog measurement chains. The single-amplifier configuration in the 8-pin SOIC package also simplifies designs that need one high-voltage amplifier rather than a dual or quad device. The low bias current is useful when the source impedance is high enough that input leakage would otherwise create a meaningful voltage error.
A practical design should begin with the manufacturer datasheet pin configuration and typical application circuits. Keep sensitive input and feedback routes short, provide stable decoupling close to the supply pins, and verify amplifier stability for the intended capacitive loading. Avoid allowing input voltage to exceed the supply rails because excess input current can flow during abnormal operating conditions, and keep the input current below the recommended 10 mA limit.
This page combines the OPA172ID operating limits, package details, application guidance, drop-in alternatives, and engineering trade-offs into one practical reference for high-voltage analog design. It also distinguishes direct pin-compatible choices from related family members so that replacement decisions are based on voltage range, bandwidth, noise, bias current, and output capability rather than package similarity alone.
Drop-in alternatifler için OPA172ID — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller OPA172ID (aynı form faktörü ve ayağa oturma) — farklı olan Input Bias Current, Input Offset Voltage, Input Offset Voltage Drift.
OPA171ID
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
OPA170ID
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
OPA192ID
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →OPA197ID
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →OPA992ID
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
OPA172ID Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Single operational amplifier |
| Number of Channels | 1 channel |
| Maximum Supply Voltage | 36 V |
| Minimum Supply Voltage | 4.5 V |
| Dual-Supply Operating Range | ±2.25 V to ±18 V |
| Gain-Bandwidth Product | 10 MHz |
| Input Offset Voltage | ±0.2 mV |
| Input Offset Voltage Drift | ±0.3 μV/°C |
| Input Bias Current | ±8 pA |
| Input Noise Density | 7 nV/√Hz |
| Durağan Akım | 1.6 mA per amplifier |
| Output Topology | Rail-to-rail output |
| Recommended Input Current Limit | 10 mA maximum |
| Paket | 8-pin SOIC |
| Montaj Türü | Surface mount |
OPA172ID Pin Yapısı
| Pin 1 | OUT — Amplifier output |
| Pin 2 | V- — Negative supply connection |
| Pin 3 | +IN — Non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | -IN — Inverting input |
| Pin 6 | +IN — Non-inverting input |
| Pin 7 | OUT — Amplifier output |
| Pin 8 | V+ — Positive supply connection |
Tipik Uygulamalar
OPA172ID için uygundur 6 uygulamas: High-Impedance Sensor Signal Conditioning, Industrial Current-Loop Interface, Precision Audio Buffer, Precision Voltage Buffer, Test and Measurement Front End, Low-Power Embedded Control Signal Chain.
High-Impedance Sensor Signal Conditioning
OPA172ID fits high-impedance sensor signal conditioning because its input bias current is ±8 pA and input-noise density is 7 nV/√Hz. These characteristics reduce source-loading errors and preserve small signals from resistive sensors, photodiode-related circuits, and high-resistance dividers. The 10 MHz gain-bandwidth product supports moderate-bandwidth amplification rather than only static measurements. Use a non-inverting or differential stage around the amplifier, maintain short feedback paths, and confirm the input common-mode range for the selected supply and gain. Because leakage from PCB contamination can dominate at picoamp input levels, clean boards and guarded input routing are as important as the device selection.
Önerilen
Industrial Current-Loop Interface
OPA172ID is appropriate for an industrial 4–20 mA current-loop receiver because it combines a 36 V maximum supply with a 1.6 mA quiescent current and ±8 pA input bias current. It can operate from higher-voltage industrial rails while maintaining low input-current error. The 10 MHz bandwidth allows the receiver to process both the slowly varying measurement signal and diagnostic test waveforms. A precision resistor converts the loop current into voltage, while the amplifier provides gain and filtering. Confirm input and output common-mode limits, output swing, and stability with the final feedback network across the full supply range.
Önerilen
Precision Audio Buffer
OPA172ID can serve as a precision audio buffer when low noise and high input impedance are more important than high-frequency slew performance. Its 7 nV/√Hz input-noise density and ±8 pA bias current reduce added noise and loading, while the 10 MHz gain-bandwidth product covers many audio-band and control-signal tasks. Rail-to-rail output helps retain useful swing from a single supply. For audio paths, verify the actual output swing into the selected load, keep the feedback loop short, and add appropriate output isolation if capacitive loads could compromise stability. The amplifier should not replace a dedicated wideband audio output stage when very low distortion at high frequency is required.
Önerilen
Precision Voltage Buffer
OPA172ID works well as a precision voltage buffer when the source has high impedance and the load must be isolated. A voltage follower presents very high input impedance and low output impedance, preventing the source from being loaded while retaining the measured voltage. The amplifier’s ±0.2 mV input offset, ±0.3 μV/°C offset drift, and ±8 pA bias current support accurate low-level measurements. Its 1.6 mA quiescent current also suits power-conscious instrumentation. Check the input offset and bias-current contributions against the source impedance, verify common-mode range during startup, and ensure that capacitive loading at the output remains within the stability conditions shown in the manufacturer datasheet.
Önerilen
Test and Measurement Front End
OPA172ID can form the input stage of a test and measurement front end because it combines a 10 MHz gain-bandwidth product with low noise and very low bias current. It can amplify modest sensor outputs before a higher-bandwidth converter or digitization stage while operating from supplies up to 36 V. Its low offset voltage and offset drift help preserve accuracy as the front end gains small signals. Use the manufacturer’s typical application circuit as the starting point, place input and feedback components close to the device, and account for gain-bandwidth and closed-loop bandwidth at the selected noise-gain setting. Verify input limits before connecting external test fixtures that may exceed the supply rails.
Önerilen
Low-Power Embedded Control Signal Chain
OPA172ID is suitable for embedded control and data-acquisition signal chains that require one precision amplifier rather than a multi-channel package. Its 1.6 mA quiescent current helps control system power, and the ±8 pA input bias current is valuable when conditioning high-impedance dividers or sensor outputs. The 4.5 V to 36 V supply range accommodates several industrial and automotive-system power environments. Use the amplifier in a non-inverting or differential topology, add filtering where bandwidth must be constrained, and ensure that shutdown behavior does not leave the input stage forward-biased. The 8-pin SOIC package also supports compact layouts when routing and thermal spacing permit.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: OPA172ID — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | OPA171ID | OPA170ID | OPA192ID | OPA197ID | OPA992ID |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
Ana Farklılayıcılar
- Low-noise, high-impedance amplification (karşılaştırma:OPA992ID)
- Lower quiescent-current operating point (karşılaştırma:OPA171ID)
- Precision offset performance for measurement chains (karşılaştırma:OPA192ID)
Tasarım Notları
Do not allow an input voltage to exceed the amplifier supply rails. The Texas Instruments datasheet states that excessive input current can flow as VIN rises and recommends limiting input current to 10 mA. This is especially important during shutdown, supply sequencing, and fault conditions. Add series input resistance or clamp protection where external signals can exceed the local supply range, and verify that protection-network leakage does not defeat the circuit’s low-noise or low-bias-current requirements.
Place supply-decoupling capacitors close to the V+ and V− pins and keep the feedback components adjacent to the amplifier. Sensitive input traces should be short, physically separated from switching or high-current paths, and guarded where leakage from flux residue or board contamination could approach the ±8 pA input-bias-current level. Use a continuous ground reference under the SOIC footprint where the PCB stack-up permits, and avoid routing input nets beneath noisy power stages.
Check closed-loop stability with the intended source impedance, load capacitance, and feedback network rather than assuming unity-gain stability applies everywhere. OPA172ID has a 10 MHz gain-bandwidth product, so small parasitic capacitances can alter phase margin at high closed-loop gain or during fast transients. Use the manufacturer’s typical application information to select feedback resistors and compensation values, and probe output settling when driving cables, ADC inputs, or capacitive loads.
Uyumluluk Bilgisi
The verified product information identifies the manufacturer, package, electrical characteristics, and ordering code but does not state the requested compliance statuses.