Texas Instruments

OPA2132P - 8MHz Dual FET-Input Op Amp | Texas Instruments

MPN: OPA2132P ✓ نشط
+/-2.5 V to +/-18 V Vdss 50 pA maximum Id 8-PDIP Package
الحد الأدنى للطلب: 1 |

OPA2132P نظرة عامة

Texas Instruments OPA2132P is a dual, high-speed FET-input operational amplifier with 8 MHz bandwidth, 20 V/us slew rate, and input bias current rated at 50 pA maximum. It operates from ±2.5 V to ±18 V according to the product listing information and is packaged in an 8-pin PDIP. The device is designed for general-purpose, audio, data-acquisition, and communications applications, particularly when the source impedance is high.

An operational amplifier is a voltage-gain stage used to amplify the difference between two input voltages. The OPA2132P belongs to the FET-input operational amplifier family, using field-effect transistor input stages to provide very low input bias current. This makes the device suitable for high-impedance sources, audio signal chains, measurement front ends, and feedback networks where conventional bipolar-input amplifiers may load the source excessively.

The OPAx132 family combines high speed with low noise and low distortion. Key characteristics identified in the manufacturer documentation include 8 MHz wide bandwidth, 20 V/us high slew rate, 0.00008% low distortion, and 130 dB open-loop gain with a 600 ohm load. The dual configuration provides two amplifiers in one package, simplifying balanced audio, active filtering, and dual-channel signal-conditioning designs while reducing the number of external packages.

OPA2132P is intended for applications requiring low input bias current and accurate signal handling. The 5 pA maximum input bias current supports high-impedance instrumentation and source-following configurations, while the 8 MHz bandwidth and 20 V/us slew rate allow the amplifier to process higher-frequency signals and reproduce large-amplitude waveforms with low distortion. The 500 uV maximum offset voltage specification is also relevant to precision dc and audio applications.

Common uses include audio preamplifiers, active filters, data-conversion input buffers, communications interfaces, and instrumentation amplifiers. In a high-impedance audio input stage, the low bias current helps preserve the source signal. In an active filter, the high bandwidth and slew rate support faster signal transitions. In data-acquisition circuits, the dual package can support two signal channels or a gain stage with an active feedback network.

Designers should confirm the complete pin assignment, input common-mode range, output swing, supply-current behavior, stability requirements, and recommended external components in the manufacturer datasheet before layout. Decoupling capacitors should be placed close to the supply pins, and feedback components should follow the recommended values. PCB leakage and contamination should also be controlled when the very low input bias current is central to the design.

This product page combines the OPA2132P technical characteristics, source links, application guidance, and drop-in replacement information to support faster component selection and PCB implementation. Use the Request a Quote form on this page for current commercial availability and lead-time information.

بدائل مباشرة لـ OPA2132P — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

OPA2132PA

✅ بديل مباشر
📦 8-PDIP
Same OPAx132 dual-amplifier family and 8-PDIP package; the manufacturer naming distinction is

📋 بديل مرجعي (غير موجود في الكتالوج)

OPA2134PA

✅ بديل مباشر
📦 8-PDIP
Same 8-PDIP dual-amplifier package, while the OPAx134 family has different input and distortion characteristics:

📋 بديل مرجعي (غير موجود في الكتالوج)

OPA2132P الحدود القصوى والخصائص الكهربائية

Amplifier Type Dual FET-input operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 8 MHz
Slew Rate 20 V/us
Input Bias Current 50 pA maximum
Low-Noise Input Current 5 pA
Low Distortion 0.00008%
Open-Loop Gain 130 dB with 600 ohm load
Supply Voltage Range +/-2.5 V to +/-18 V
Offset Voltage 500 uV maximum
Input Transistor Type FET
العلبة 8-PDIP
نوع التركيب Through-hole
Application Category General-purpose, audio, data-acquisition, and communications

دليل تكوين أطراف OPA2132P 8-pdip

تكوين الأطراف لـ OPA2132P (حزمة 8-pdip). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 8-pdip لـ OPA2132P

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ OPA2132P.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

OPA2132P مناسب لـ 6 التطبيقs: High-Impedance Audio Preamp, Active Audio Filter, Data-Acquisition Input Buffer, Communications Signal Conditioning, Precision Instrumentation Buffer, Balanced Audio Output.

🎧

High-Impedance Audio Preamp

The OPA2132P fits a high-impedance audio preamplifier because its FET input stage limits input bias current to 50 pA maximum while retaining 8 MHz bandwidth and 20 V/us slew rate. In a source-follower or non-inverting gain stage, the low bias current reduces loading on the preceding source and helps preserve signal amplitude. The 0.00008% distortion specification also makes the dual amplifier useful in audio paths requiring low signal degradation. Use one channel for the signal and the other for an active filter, buffer, or balanced drive stage, while checking output swing and load compatibility against the manufacturer electrical-characteristics table.

🔧

Active Audio Filter

The OPA2132P is appropriate for an active audio filter requiring low bias current, ample bandwidth, and fast settling. Its 8 MHz gain-bandwidth product and 20 V/us slew rate allow the active stage to handle high-frequency components and larger signal transitions with low distortion. In a low-pass, high-pass, or equalizer network, the FET inputs help preserve signals from high-impedance sources without adding substantial loading. The two channels can implement linked filter sections or independent channels. Select resistor and capacitor values against the closed-loop bandwidth and stability guidance in the Texas Instruments OPAx132 datasheet.

📺

Data-Acquisition Input Buffer

OPA2132P can serve as a low-input-current buffer in a data-acquisition front end when the source impedance is high. Its 50 pA maximum input bias current minimizes the current drawn from sensors or sensor-conditioning networks, while 8 MHz bandwidth supports signals above the precision-audio range. The dual package allows one channel to buffer the measurement input and the other to drive an anti-alias or gain stage. Check the complete input common-mode range, offset behavior, and output-swing limits for the selected supply before implementation, and use the manufacturer application guidance for a stable closed-loop configuration.

🌐

Communications Signal Conditioning

The OPA2132P is suited to communications signal-conditioning stages that require low input current and fast response. The 50 pA maximum input bias current is useful when the amplifier follows a high-impedance source, while 8 MHz bandwidth and 20 V/us slew rate support faster waveforms than conventional precision op-amps. Both channels can be used for receive-path conditioning, active impedance conversion, or differential signal handling. The 130 dB open-loop gain with a 600 ohm load provides useful dc-loop gain, but the actual signal integrity depends on the feedback network, load, supply configuration, and board layout. Review stability and bandwidth-distortion data before releasing the circuit.

🏭

Precision Instrumentation Buffer

OPA2132P supports precision instrumentation-buffer functions where low input bias current helps reduce measurement errors. The 500 uV maximum offset voltage and 130 dB open-loop gain with a 600 ohm load are important when the circuit uses high closed-loop gain, while the 5 pA low-noise input-current figure supports high-impedance feedback networks. One amplifier channel can buffer the measurement input and the other can provide gain or active feedback. The complete input common-mode range and output-swing behavior must be checked at the actual supply voltage, and PCB leakage should be minimized because contamination can undermine the benefit of the very low input current.

🎚️

Balanced Audio Output

The dual OPA2132P can support balanced audio output circuitry where matched dual channels and low distortion are useful. The 0.00008% distortion characteristic, 8 MHz bandwidth, and 20 V/us slew rate help maintain signal integrity through gain and driver stages, while 50 pA maximum input bias current protects high-impedance upstream nodes from excessive loading. The two amplifiers can form a balanced gain stage or drive two sides of a balanced output network. Confirm output-current capability, voltage swing, and load stability for the target amplifier and verify the power-supply layout because the available supply range extends to ±18 V.

What is the OPA2132P?
The OPA2132P is a dual, high-speed FET-input operational amplifier from Texas Instruments with 8 MHz gain-bandwidth product, 20 V/us slew rate, and 50 pA maximum input bias current. According to the Texas Instruments OPAx132 datasheet, the OPAx132 family combines low input current with low noise and low distortion for general-purpose, audio, data-acquisition, and communications designs. The OPA2132P is supplied in an 8-pin PDIP package and contains two independent amplifiers.
What is the bandwidth of the OPA2132P?
The OPA2132P has an 8 MHz gain-bandwidth product. According to the Texas Instruments OPAx132 datasheet, this bandwidth supports faster signal processing than low-frequency precision amplifiers while retaining the low input bias current of a FET-input design. Bandwidth alone does not determine usable closed-loop bandwidth; the final response also depends on the selected gain, feedback topology, load, and circuit stability. Use the manufacturer datasheet for the recommended application circuits.
Why is the OPA2132P suitable for high-impedance sources?
The OPA2132P is suitable for high-impedance sources because its FET input stage has a maximum input bias current of 50 pA. According to the Texas Instruments OPAx132 datasheet, the OPAx132 series is especially appropriate where high source impedance is encountered. The low bias current reduces the loading effect on the source and supports audio buffers, sensor interfaces, and measurement circuits. Board cleanliness and leakage control remain important when operating at very high source impedances.
What supply voltage does the OPA2132P support?
The OPA2132P supports a supply voltage range of ±2.5 V to ±18 V. According to the Texas Instruments OPAx132 datasheet, this range allows operation from single-supply-compatible rail arrangements through higher dual-supply rails. The exact usable input and output common-mode limits depend on the selected supply and circuit configuration. Confirm those limits and the required decoupling network in the manufacturer datasheet before finalizing a PCB design.
Where can I download the OPA2132P datasheet PDF?
The official OPA2132P datasheet PDF is available from the Texas Instruments product page at https://www.ti.com/lit/ds/symlink/opa2132.pdf. The document is titled OPAx132 High-Speed FET-Input Operational Amplifiers and covers the OPA132, OPA2132, and OPA4132 family. Use the pin-description table, electrical characteristics, typical performance plots, and application sections in that manufacturer document when designing the circuit.
Where is the OPA2132P pinout?
The OPA2132P pinout is published in the Texas Instruments OPAx132 datasheet at https://www.ti.com/lit/ds/symlink/opa2132.pdf. The device uses an 8-pin PDIP package with two operational amplifiers. Use the pin-description table to assign supply, input, output, offset-null, and compensation connections exactly as specified by the manufacturer. Because the dual-amplifier pin arrangement is package-specific, do not assume that it matches every other 8-pin dual op-amp.
Is OPA2132P suitable for audio applications?
Yes, the OPA2132P is suitable for audio applications because it combines 8 MHz bandwidth, 20 V/us slew rate, 0.00008% distortion, and a low-noise FET input stage. According to the Texas Instruments OPAx132 datasheet, the OPAx132 family is an excellent choice for audio applications, particularly where high source impedance is encountered. It can be used in preamplifier, buffer, filter, and active-feedback audio signal paths after the output-load and supply requirements are verified.
What can replace the OPA2132P?
The OPA2132P can be replaced only by a dual operational amplifier with the same PDIP-8 footprint, compatible pinout, suitable input bias current, adequate bandwidth, and acceptable supply and common-mode limits. The available cross-reference search identifies replacement candidates, but it does not provide enough verified part-specific details to confirm five drop-in alternatives for this listing. Review the manufacturer pinout and electrical characteristics before approving any substitute in production.
Is the OPA2132P the same as the OPA2134?
The OPA2132P and OPA2134 are not identical in every operating characteristic. According to the Texas Instruments OPAx132 datasheet, the OPA2132P has 8 MHz bandwidth, 20 V/us slew rate, 50 pA maximum input bias current, 130 dB open-loop gain with a 600 ohm load, and 500 uV maximum offset voltage. OPA2134 specifications differ in relevant areas, so a replacement should be checked for the exact requirements of the audio, instrumentation, or communications circuit.
When should I choose the OPA2132P over another dual op amp?
Choose the OPA2132P when the design benefits from very low FET input bias current, 8 MHz bandwidth, 20 V/us slew rate, and low distortion in a dual 8-pin PDIP package. According to the Texas Instruments OPAx132 datasheet, it is particularly useful with high source impedance and in general-purpose, audio, data-acquisition, and communications systems. Choose another amplifier when its input stage, common-mode range, output swing, noise density, or power consumption better matches the system requirements.
What is the OPA2132P vs OPA2134PA difference for audio?
The OPA2132P is the OPAx132 family device, while OPA2134PA belongs to the OPAx134 family. According to the Texas Instruments OPAx132 datasheet, OPA2132P provides 8 MHz bandwidth, 20 V/us slew rate, 50 pA maximum input bias current, and 0.00008% distortion. A direct OPA2134PA substitution requires checking its own pinout, supply range, input bias current, offset voltage, open-loop gain, and output-drive specifications against the circuit requirements.
What are the key specifications of OPA2132P that engineers should know?
The key OPA2132P specifications are 8 MHz gain-bandwidth product, 20 V/us slew rate, 50 pA maximum input bias current, 0.00008% distortion, 130 dB open-loop gain with a 600 ohm load, ±2.5 V to ±18 V supply range, and 500 uV maximum offset voltage. According to the Texas Instruments OPAx132 datasheet, the dual FET-input device also supports general-purpose, audio, data-acquisition, and communications applications. Package, common-mode, output-swing, and current details should be checked in the same datasheet.
How should the OPA2132P be decoupled on a PCB?
Place the required supply-bypass capacitors close to the OPA2132P supply pins and keep their return paths short. According to the Texas Instruments OPAx132 datasheet, proper bypassing helps maintain stable operation with the high-speed amplifier. The exact capacitance, permitted tolerances, and whether additional ceramics are required should follow the manufacturer layout recommendations. Keep sensitive input and feedback routing away from switching nodes and high-current return paths.
How much power does the OPA2132P consume?
Power dissipation in the OPA2132P depends on the supply voltage, quiescent current, output load, and operating conditions. The manufacturer documentation identifies the supply range as ±2.5 V to ±18 V, but the exact supply-current and quiescent-current values must be taken from the OPAx132 electrical-characteristics table. For a numerical estimate, use the expression Pdissipation = ((Vplus - Vout) times Iplus) + ((Vout - Vminus) times Iminus), with the actual operating currents and output voltage.
Where can I buy OPA2132P and what is the lead time?
Use the Request a Quote form on this page to request OPA2132P pricing, stock confirmation, packaging details, and current lead time. The available distributor listings confirm the exact OPA2132P orderable device, but they do not show a qualifying quantity-break price table for this page. For production planning, request the current manufacturer and channel status along with the required quantity and package suffix.
Is OPA2132P RoHS compliant and qualified for automotive use?
The RoHS, REACH, AEC-Q100, lead-free, and halogen-free status of OPA2132P should be confirmed from the current Texas Instruments product and datasheet documentation before a compliance declaration is made. The OPA2132P is an 8-pin PDIP high-speed analog amplifier, and its package or application category does not by itself establish AEC-Q100 qualification. Use the manufacturer compliance declarations for the exact ordering code and requested destination market.

بيانات مرجعية هندسية لـ OPA2132P — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the OPA2132P when a dual-precision signal path benefits from very low input bias current, 8 MHz bandwidth, 20 V/us slew rate, and 0.00008% distortion in an 8-PDIP package. It is especially suitable for high-source-impedance audio buffers, active filters, communications interfaces, and data-acquisition input conditioning. OPA2132PA is the closest same-family candidate to investigate when the ordering-code differences matter, but verify its exact specifications and qualification status. OPA2134PA may suit some audio applications, yet it should be selected only after its input bias current, offset voltage, bandwidth, slew rate, common-mode range, and output behavior are compared with the OPA2132P requirements. For any drop-in decision, confirm the DIP-8 pinout, supply range, load stability, and application qualification rather than relying on package appearance alone.

المقارنة مع البدائل

المعامل هذا المنتج OPA2132PA OPA2134PA
Package 8-PDIP 8-PDIP 8-PDIP
Brand Texas Instruments Texas Instruments Texas Instruments
Amplifier Configuration Dual operational amplifier Dual operational amplifier Dual operational amplifier

أبرز الفروقات

  • Low-current dual input stage (مقابلOPA2134PA)
  • High-speed signal capability (مقابلOPA2134PA)
  • Low-distortion dual-amplifier implementation (مقابلOPA2134PA)

ملاحظات التصميم

Place the required supply-bypass capacitors immediately adjacent to the OPA2132P supply pins, and route their ground returns directly to the device ground reference plane. Keep feedback traces short and isolate them from clocks, switching converters, and digital return currents. Because the dual amplifier can be sensitive to parasitic capacitance at high gain, follow the recommended resistor and capacitor values in the manufacturer datasheet rather than substituting arbitrarily large compensation capacitors.

Do not assume that every dual 8-pin operational amplifier is pin-compatible with the OPA2132P. Confirm the DIP-8 pin assignment, including supply, output, offset-null, and any compensation-related pins, against the Texas Instruments pin-description table. Also verify the input common-mode range and output swing at the selected supply voltage; a matching package alone does not establish electrical compatibility.

For high-impedance sources, minimize leakage from board contamination, moisture, flux residue, and adjacent high-impedance nodes. The OPA2132P has 50 pA maximum input bias current, so the leakage current surrounding the input can materially affect the signal if it approaches that level. Use a clean PCB surface, guard structures where appropriate, and low-leakage protection devices, then validate the complete source impedance and environmental conditions.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

Compliance status for the exact OPA2132P ordering code should be confirmed through the current Texas Instruments product documentation. The available product and datasheet snippets identify the device and its electrical characteristics but do not state the requested compliance classifications.

تم التحقق من البيانات في: 2026-11-09 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

OPA2132P datasheet OPA2132P pinout OPA2132P datasheet pdf OPA2132P equivalent OPA2132P replacement OPA2132P vs OPA2134PA Texas Instruments OPA2132P OPA2132P 8MHz op amp OPA2132P 20V/us amplifier OPA2132P PDIP pinout OPA2132P audio preamplifier OPA2132P price OPA2132P stock

المكونات والمصطلحات ذات الصلة

Texas Instruments OPA2132P OPA2132PA OPA2134PA OPA2132 OPA132 OPA4132 OPAx132 dual operational amplifier FET-input operational amplifier operational amplifier voltage amplifier analog IC 8-PDIP DIP-8 surface-mount package family 8 MHz gain-bandwidth product 20 V/us slew rate 50 pA input bias current input common-mode range output swing audio preamplifier active filter data acquisition communications signal conditioning
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر