NXP Semiconductors

PCA9521D - 1MHz Dual Bidirectional I2C Buffer | NXP

MPN: PCA9521D ✗ انتهى عمره الإنتاجي
2.7 V to 3.6 V Vdss 8-pin SOIC, 3.90 mm nominal body width Package 1 MHz Speed
الحد الأدنى للطلب: 1 |

PCA9521D نظرة عامة

The NXP Semiconductors PCA9521D is a fast dual bidirectional bus buffer for I2C-bus, SMBus, PMBus, and similar two-wire systems. It buffers the SCL and SDA lines, supports bus loads up to 400 pF on each side, operates at up to 1 MHz, and is offered in an 8-pin SOIC package. The device uses a 2.7 V to 3.6 V supply range with 5.5 V tolerance on its bus-side inputs.

A bidirectional bus buffer is an interface IC that regenerates and electrically isolates two bus segments. In the I2C hierarchy, the PCA9521 belongs to the bus-buffer class rather than a controller or transceiver. It allows a master and peripheral devices to remain connected while extending usable bus loading or isolating a slow, heavily loaded segment from a faster segment. Both clock and data paths are buffered rather than treating SCL and SDA as a single multiplexed channel.

Key characteristics include a 1 MHz maximum operating frequency, two independently buffered I2C channels, 400 pF support on each side, and operation across the -40°C to 85°C industrial temperature range. The bipolar monolithic implementation is intended for low-voltage embedded systems where bus extension, isolation, or higher effective bus capacitance is required. The SOIC-8 package also supports conventional leaded-board assembly processes.

The buffer does not translate the I2C voltage domains. Its buffered inputs and outputs operate around the same low-voltage reference, making it different from level-translating devices intended to connect independently powered domains at incompatible logic levels. System designers should also treat pull-up resistor placement, total bus capacitance, rise-time limits, and the number of supported buffered segments as part of the complete interface design rather than as isolated component specifications.

Typical uses include separating a long peripheral bus from a controller, increasing aggregate I2C load capability with suitable pull-ups, and isolating maintenance or expansion connectors from the main bus. It is also useful in PMBus and SMBus-derived systems whose electrical signaling follows similar bidirectional open-drain principles. A practical design should preserve the SCL and SDA topology on both sides of the buffer and provide the required pull-up networks independently where appropriate.

Place the device close to the physical division between the two bus sections to keep each trace short and reduce susceptibility to capacitive loading and ringing. Use pull-up resistors selected for the target bus speed and capacitance, and confirm that the resulting rise time meets the controller's timing specification. Avoid introducing extra capacitance, long stubs, or unnecessary connectors on either side of the buffer.

This page combines the manufacturer's device description, electrical characteristics, package information, interface use cases, and verified substitute analysis into an engineering-focused guide. It also distinguishes true pin-compatible replacements from parts that merely share the same SOP-8 package, helping designers avoid substitutions that require PCB changes or change I2C behavior.

بدائل مباشرة لـ PCA9521D — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.

اطلب بدائل

PCA9521D المواصفات

Device Type Fast dual bidirectional bus buffer
Technology Bipolar
Supported Buses I2C-bus, SMBus, PMBus, and similar systems
Buffered Bus Channels 2 channels for SCL and SDA
Maximum Frequency 1 MHz
I2C Bus Frequency Up to 400 kHz
Supply Voltage Range 2.7 V to 3.6 V
Bus Input Voltage Tolerance 5.5 V tolerant
Bus Load per Side 400 pF
نطاق درجة حرارة التشغيل -40°C to +85°C
العلبة 8-pin SOIC, 3.90 mm nominal body width
Package Code SOP-8 / SOT96-1
عدد الدبابيس 8 pins
نوع التركيب Surface mount
Terminal Form Gull wing
Temperature Grade Industrial
Logic Compatibility Single low-voltage domain; no voltage-level translation

دليل تكوين أطراف PCA9521D sop-8 / sot96-1

تكوين الأطراف لـ PCA9521D (حزمة sop-8 / sot96-1). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة sop-8 / sot96-1 لـ PCA9521D

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ PCA9521D.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

PCA9521D مناسب لـ 6 التطبيقs: I2C Bus Extension, SMBus System Isolation, PMBus Power Management, Embedded Sensor Bus, Industrial Control Backplane, Service Connector Isolation.

🌐

I2C Bus Extension

The PCA9521D fits between two I2C bus sections when peripherals create enough capacitance to weaken the original bus. Its two buffered paths preserve separate SCL and SDA signals, while the stated 400 pF loading capability per side allows a remote section to remain usable. The buffer is placed near the physical split, with pull-up resistors sized for the capacitance and target clock rate. At frequencies approaching 1 MHz, account for propagation delay and the resulting reduction in available clock and data timing margins rather than assuming the maximum rate applies to every layout.

🖥️

SMBus System Isolation

The PCA9521D can divide an SMBus-derived network into buffered segments when one cable or connector branch introduces excessive loading. Because the device buffers SCL and SDA independently, clock and data propagation remain aligned across the two sections. The 1 MHz device capability covers conventional SMBus rates while providing additional operating headroom. Select pull-up resistance for each section based on its capacitance, keep branch traces short, and confirm the complete system still meets the master's timeout and rise-time requirements.

⚡

PMBus Power Management

The PCA9521D is applicable to PMBus-style power-management systems where a controller communicates over SCL and SDA with converters, sensors, and other management components. Buffering helps isolate a distant or heavily loaded management branch from the controller bus, improving signal integrity without changing the protocol implemented by the devices. The 400 pF-per-side capability is valuable in systems with multiple routed branches, but the designer must still observe PMBus timing, pull-up sizing, and any clock-stretching behavior specified by the participating devices.

🧩

Embedded Sensor Bus

The PCA9521D separates a group of remote sensors from a host processor when long traces or multiple sensor inputs would otherwise increase the total bus capacitance. The separated SCL and SDA paths preserve the familiar two-wire sensor interface, and the buffer can support up to 400 pF on either side under the stated conditions. Place it near the cable or connector entry, provide local pull-ups for the remote segment when appropriate, and verify rise time at the longest operating temperature because cable capacitance and pull-up tolerance directly affect edge speed.

🏭

Industrial Control Backplane

The PCA9521D can isolate an I2C-style control backplane from a connector, cable, or populated module that presents substantial capacitive loading. Its 1 MHz capability supports faster industrial control traffic, while the industrial temperature range of -40°C to 85°C suits equipment expected to operate across varied ambient conditions. Keep the two routed bus regions physically distinct, place decoupling close to the device supply pins, and use the pull-up networks to control edge rates. Review timing margins across the full temperature range and with the worst-case bus capacitance.

🔧

Service Connector Isolation

The PCA9521D is useful between a main controller bus and a service or expansion connector that may be cabled to a longer harness. Buffering the connector branch protects the local bus from harness capacitance and reduces the loading presented to the controller. Because the PCA9521D is not a level translator, both sides must remain within the same compatible logic domain. Apply appropriate pull-ups on each side, keep the connector-side routing compact, and validate SCL and SDA rise times at the highest intended bus frequency.

What is the PCA9521D and what does it do?
The PCA9521D is a fast dual bidirectional bus buffer that separates two sections of an I2C, SMBus, PMBus, or similar bus. According to the NXP product information, it buffers both SCL and SDA, extends the bus-load limit, and supports loads of up to 400 pF on each side. Its 1 MHz capability makes it appropriate for relatively fast two-wire communication links.
What is the maximum operating frequency of PCA9521D?
The PCA9521D operates at up to 1 MHz, while its published I2C-bus operating frequency is listed as up to 400 kHz. Distributor catalog information identifies it as a 1 MHz buffer. The usable frequency still depends on bus capacitance, pull-up resistance, clock stretching, propagation delay, and the rise time required by the system.
What supply voltage does PCA9521D require?
The PCA9521D operates from a 2.7 V to 3.6 V supply and tolerates bus-side input voltages up to 5.5 V. This is important when both sections of the connected bus use low-voltage signaling. The device does not translate between different logic voltage domains, so separate level-shift circuitry may still be required elsewhere in the system.
Where can I download the PCA9521D datasheet PDF?
The official PCA9521D datasheet PDF is available from NXP at the product-data link on the NXP PCA9521D page. Use the manufacturer PDF for the authoritative pin description, electrical characteristics, application diagram, and recommended operating conditions. The separate PCA9521D product page is also useful for package and lifecycle information.
Where can I find the PCA9521D pinout?
The PCA9521D pinout is shown in the NXP manufacturer datasheet rather than in the catalog snippets. The component uses an 8-pin SOIC outline, but pin names and electrical roles must be assigned from the datasheet's pin-description table. Use that table when creating the PCB footprint and connecting SCL, SDA, supply, and ground.
Can PCA9521D extend an I2C bus with 400 pF on each side?
Yes, the PCA9521D is designed to buffer two I2C-style bus sections and supports up to 400 pF on each side when used with suitable pull-ups and layout. The buffer separates capacitance and weak signal degradation between sections. It does not guarantee 1 MHz operation at maximum capacitance, so timing and rise-time checks remain necessary.
Does PCA9521D translate I2C voltage levels?
No, the PCA9521D is a bidirectional bus buffer, not a voltage-level translator. Both connected bus sections use the same low-voltage signaling environment, with a 2.7 V to 3.6 V device supply and bus inputs tolerant to 5.5 V. Use a dedicated level-translating buffer when independently powered domains require voltage conversion.
What is the best drop-in replacement for PCA9521D?
The best drop-in replacement is the one that preserves the SOIC-8 footprint, pin assignments, operating voltage, bidirectional behavior, and required bus timing. No alternative in the substitute results is confirmed as a true pin-to-pin replacement for the PCA9521D. Parts sharing only the SOP-8 outline should not be treated as drop-in equivalents without a verified pin-level comparison.
What can replace PCA9521D in an I2C design?
A valid replacement must provide separate SCL and SDA buffering, support the required capacitance and frequency, and use the same pin functions and package footprint. Candidate devices such as the PCA9507D and PCA9517AD use SOP-8 packages, but their bus functions and electrical characteristics differ. A PCB respin or timing revalidation may therefore be necessary.
PCA9521D versus PCA9507D: which is better for a 1 MHz bus?
The PCA9521D is the better match when a design specifically requires a fast 1 MHz dual SCL/SDA buffer. The PCA9507D is associated with a 100 kHz bus rate in the comparison data, so it is not an equivalent choice for a 1 MHz design. Both may appear in SOP-8 packages, but package similarity alone does not establish pin compatibility.
When should I choose PCA9521D instead of PCA9517AD?
Choose the PCA9521D when the design requires a 1 MHz bidirectional SCL/SDA buffer with up to 400 pF support per side. The PCA9517AD is identified as a dual-supply level-translating I2C repeater and is better suited when voltage translation between domains matters. The PCA9521D is the stronger choice for same-domain bus extension.
Is PCA9521D suitable for SMBus and PMBus systems?
Yes, the NXP product information identifies SMBus and PMBus as application classes for the PCA9521D. Its bidirectional buffering function is appropriate for compatible two-wire systems that use the same low-voltage signaling domain. Verify each system's timing, pull-up arrangement, and electrical limits before reusing an I2C design unchanged.
How should pull-up resistors be selected for PCA9521D?
Select pull-up resistors for each buffered bus section using the target frequency, total capacitance, sink-current limits, and required rise time. Because the PCA9521D separates the sections, each side may need its own pull-up network. Avoid placing the pull-ups where they unnecessarily load the source bus or create slow edges on the buffered side.
Is PCA9521D in stock and what is its lead time?
Current stock and lead time should be requested through the Request a Quote form on this page. The manufacturer product page contains historical product information and should be checked for lifecycle status before a new design is released. For production planning, confirm the exact orderable suffix, reel configuration, quantity, and delivery schedule with the supplier.
Where can I buy PCA9521D and check its current price?
Use the Request a Quote form on this page to request the current PCA9521D price, stock position, minimum order quantity, and lead time. The exact manufacturer ordering code and packaging suffix should be confirmed during quotation. This avoids relying on a stale historical price for an archived or mature interface IC.
What are the key specifications of PCA9521D that engineers should know?
The key PCA9521D specifications are a 1 MHz maximum operating frequency, 400 pF bus loading per side, a 2.7 V to 3.6 V supply range, 5.5 V-tolerant bus inputs, two buffered SCL/SDA paths, and a -40°C to 85°C operating range. The device is a bipolar monolithic IC in an 8-pin SOIC package and provides buffering rather than voltage translation.

بيانات مرجعية هندسية لـ PCA9521D — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the PCA9521D when an I2C-style bus must be divided into two buffered sections that remain in the same low-voltage logic domain. Its combination of a 1 MHz maximum operating frequency, up to 400 pF loading per side, and an 8-pin SOIC package is well suited to cable, connector, and backplane isolation. The PCA9507D is a different 100 kHz-class bus-buffer solution and is not a substitute for a 1 MHz requirement. The PCA9517AD is preferable when voltage translation between independently powered domains is the primary requirement. For any proposed substitute, verify the pin mapping, propagation delay, pull-up arrangement, supply limits, and maximum bus capacitance rather than relying on package appearance alone.

المقارنة مع البدائل

المعامل هذا المنتج
Brand NXP Semiconductors
Package 8-pin SOIC
Device Type Fast dual bidirectional bus buffer
Technology Bipolar
Maximum Frequency 1 MHz
I2C Bus Frequency Up to 400 kHz
Supply Voltage Range 2.7 V to 3.6 V
Bus Input Voltage Tolerance 5.5 V tolerant
Bus Load per Side 400 pF
Operating Temperature Range -40°C to +85°C

أبرز الفروقات

  • Higher documented operating rate than the compared PCA9507D (مقابلPCA9507D)
  • Purpose-built SCL and SDA buffering rather than level translation (مقابلPCA9517AD)
  • High capacitive-load support for split-bus designs (مقابلPCA9507D)

ملاحظات التصميم

Place the PCA9521D close to the physical boundary between the source and load bus sections. Keep each SCL and SDA trace short, avoid long stubs, and place the local supply decoupling capacitor adjacent to the device. This arrangement limits the capacitance seen by the source side and gives the buffered side a cleaner transition boundary. Route the two channels consistently so that clock and data see similar trace geometry.

Calculate the pull-up resistance for each side from its total bus capacitance and the required clock and data rise time. Stronger pull-ups reduce rise time but increase the low-level sink current demanded from the connected device. Verify that the controller and peripherals can tolerate that current at the maximum voltage. After layout is complete, measure SCL and SDA rise time at the remote endpoint and check timing margin across the intended temperature range.

Do not treat the 5.5 V input tolerance as permission to operate two incompatible logic domains through the PCA9521D. The device buffers signals within a common low-voltage domain and does not perform voltage translation. Also avoid assuming that a part in the same SOP-8 package is a drop-in replacement: confirm every pin, supply range, direction behavior, capacitance rating, and bus timing requirement before substitution.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The available product information does not provide a definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement. The component is an industrial-temperature interface IC rather than an automotive-qualified device.

تم التحقق من البيانات في: 2026-11-19 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

PCA9521D datasheet PCA9521D datasheet pdf PCA9521D pinout PCA9521D schematic PCA9521D equivalent PCA9521D replacement PCA9521D cross reference PCA9521D vs PCA9507D PCA9521D vs PCA9517AD PCA9521D SOIC-8 pinout PCA9521D price PCA9521D stock NXP PCA9521D PCA9521D I2C bus buffer PCA9521D application circuit

المكونات والمصطلحات ذات الصلة

NXP Semiconductors PCA9521D PCA9507D PCA9517AD PCA9515APWR I2C-bus SMBus PMBus bidirectional bus buffer interface IC bus buffer SCL SDA bus capacitance 1 MHz 400 pF 2.7 V to 3.6 V 5.5 V tolerance bipolar monolithic integrated circuit SOIC-8 SOT96-1 surface-mount package level translator industrial temperature grade
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر