PCA9521D - 1MHz Dual Bidirectional I2C Buffer | NXP
MPN: PCA9521D ✗ اختتامِ زندگیPCA9521D جائزہ
A bidirectional bus buffer is an interface IC that regenerates and electrically isolates two bus segments. In the I2C hierarchy, the PCA9521 belongs to the bus-buffer class rather than a controller or transceiver. It allows a master and peripheral devices to remain connected while extending usable bus loading or isolating a slow, heavily loaded segment from a faster segment. Both clock and data paths are buffered rather than treating SCL and SDA as a single multiplexed channel.
Key characteristics include a 1 MHz maximum operating frequency, two independently buffered I2C channels, 400 pF support on each side, and operation across the -40°C to 85°C industrial temperature range. The bipolar monolithic implementation is intended for low-voltage embedded systems where bus extension, isolation, or higher effective bus capacitance is required. The SOIC-8 package also supports conventional leaded-board assembly processes.
The buffer does not translate the I2C voltage domains. Its buffered inputs and outputs operate around the same low-voltage reference, making it different from level-translating devices intended to connect independently powered domains at incompatible logic levels. System designers should also treat pull-up resistor placement, total bus capacitance, rise-time limits, and the number of supported buffered segments as part of the complete interface design rather than as isolated component specifications.
Typical uses include separating a long peripheral bus from a controller, increasing aggregate I2C load capability with suitable pull-ups, and isolating maintenance or expansion connectors from the main bus. It is also useful in PMBus and SMBus-derived systems whose electrical signaling follows similar bidirectional open-drain principles. A practical design should preserve the SCL and SDA topology on both sides of the buffer and provide the required pull-up networks independently where appropriate.
Place the device close to the physical division between the two bus sections to keep each trace short and reduce susceptibility to capacitive loading and ringing. Use pull-up resistors selected for the target bus speed and capacitance, and confirm that the resulting rise time meets the controller's timing specification. Avoid introducing extra capacitance, long stubs, or unnecessary connectors on either side of the buffer.
This page combines the manufacturer's device description, electrical characteristics, package information, interface use cases, and verified substitute analysis into an engineering-focused guide. It also distinguishes true pin-compatible replacements from parts that merely share the same SOP-8 package, helping designers avoid substitutions that require PCB changes or change I2C behavior.
کے لیے ڈراپ اِن متبادل PCA9521D — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔
متبادل کی درخواست کریںPCA9521D تفصیلات
| Device Type | Fast dual bidirectional bus buffer |
| Technology | Bipolar |
| Supported Buses | I2C-bus, SMBus, PMBus, and similar systems |
| Buffered Bus Channels | 2 channels for SCL and SDA |
| Maximum Frequency | 1 MHz |
| I2C Bus Frequency | Up to 400 kHz |
| Supply Voltage Range | 2.7 V to 3.6 V |
| Bus Input Voltage Tolerance | 5.5 V tolerant |
| Bus Load per Side | 400 pF |
| آپریٹنگ درجہ حرارت رینج | -40°C to +85°C |
| پیکیج | 8-pin SOIC, 3.90 mm nominal body width |
| Package Code | SOP-8 / SOT96-1 |
| پنز کی تعداد | 8 pins |
| ماؤنٹنگ ٹائپ | Surface mount |
| Terminal Form | Gull wing |
| Temperature Grade | Industrial |
| Logic Compatibility | Single low-voltage domain; no voltage-level translation |
PCA9521D sop-8 / sot96-1 پن کنفیگریشن گائیڈ
PCA9521D (sop-8 / sot96-1 پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں PCA9521D.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
PCA9521D کے لیے موزوں ہے 6 ایپلیکیشنs: I2C Bus Extension, SMBus System Isolation, PMBus Power Management, Embedded Sensor Bus, Industrial Control Backplane, Service Connector Isolation.
I2C Bus Extension
The PCA9521D fits between two I2C bus sections when peripherals create enough capacitance to weaken the original bus. Its two buffered paths preserve separate SCL and SDA signals, while the stated 400 pF loading capability per side allows a remote section to remain usable. The buffer is placed near the physical split, with pull-up resistors sized for the capacitance and target clock rate. At frequencies approaching 1 MHz, account for propagation delay and the resulting reduction in available clock and data timing margins rather than assuming the maximum rate applies to every layout.
تجویز کردہ
SMBus System Isolation
The PCA9521D can divide an SMBus-derived network into buffered segments when one cable or connector branch introduces excessive loading. Because the device buffers SCL and SDA independently, clock and data propagation remain aligned across the two sections. The 1 MHz device capability covers conventional SMBus rates while providing additional operating headroom. Select pull-up resistance for each section based on its capacitance, keep branch traces short, and confirm the complete system still meets the master's timeout and rise-time requirements.
تجویز کردہ
PMBus Power Management
The PCA9521D is applicable to PMBus-style power-management systems where a controller communicates over SCL and SDA with converters, sensors, and other management components. Buffering helps isolate a distant or heavily loaded management branch from the controller bus, improving signal integrity without changing the protocol implemented by the devices. The 400 pF-per-side capability is valuable in systems with multiple routed branches, but the designer must still observe PMBus timing, pull-up sizing, and any clock-stretching behavior specified by the participating devices.
تجویز کردہ
Embedded Sensor Bus
The PCA9521D separates a group of remote sensors from a host processor when long traces or multiple sensor inputs would otherwise increase the total bus capacitance. The separated SCL and SDA paths preserve the familiar two-wire sensor interface, and the buffer can support up to 400 pF on either side under the stated conditions. Place it near the cable or connector entry, provide local pull-ups for the remote segment when appropriate, and verify rise time at the longest operating temperature because cable capacitance and pull-up tolerance directly affect edge speed.
تجویز کردہ
Industrial Control Backplane
The PCA9521D can isolate an I2C-style control backplane from a connector, cable, or populated module that presents substantial capacitive loading. Its 1 MHz capability supports faster industrial control traffic, while the industrial temperature range of -40°C to 85°C suits equipment expected to operate across varied ambient conditions. Keep the two routed bus regions physically distinct, place decoupling close to the device supply pins, and use the pull-up networks to control edge rates. Review timing margins across the full temperature range and with the worst-case bus capacitance.
تجویز کردہ
Service Connector Isolation
The PCA9521D is useful between a main controller bus and a service or expansion connector that may be cabled to a longer harness. Buffering the connector branch protects the local bus from harness capacitance and reduces the loading presented to the controller. Because the PCA9521D is not a level translator, both sides must remain within the same compatible logic domain. Apply appropriate pull-ups on each side, keep the connector-side routing compact, and validate SCL and SDA rise times at the highest intended bus frequency.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PCA9521D — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ |
|---|---|
| Brand | NXP Semiconductors |
| Package | 8-pin SOIC |
| Device Type | Fast dual bidirectional bus buffer |
| Technology | Bipolar |
| Maximum Frequency | 1 MHz |
| I2C Bus Frequency | Up to 400 kHz |
| Supply Voltage Range | 2.7 V to 3.6 V |
| Bus Input Voltage Tolerance | 5.5 V tolerant |
| Bus Load per Side | 400 pF |
| Operating Temperature Range | -40°C to +85°C |
اہم امتیازی خصوصیات
- Higher documented operating rate than the compared PCA9507D (بمقابلہPCA9507D)
- Purpose-built SCL and SDA buffering rather than level translation (بمقابلہPCA9517AD)
- High capacitive-load support for split-bus designs (بمقابلہPCA9507D)
ڈیزائن نوٹس
Place the PCA9521D close to the physical boundary between the source and load bus sections. Keep each SCL and SDA trace short, avoid long stubs, and place the local supply decoupling capacitor adjacent to the device. This arrangement limits the capacitance seen by the source side and gives the buffered side a cleaner transition boundary. Route the two channels consistently so that clock and data see similar trace geometry.
Calculate the pull-up resistance for each side from its total bus capacitance and the required clock and data rise time. Stronger pull-ups reduce rise time but increase the low-level sink current demanded from the connected device. Verify that the controller and peripherals can tolerate that current at the maximum voltage. After layout is complete, measure SCL and SDA rise time at the remote endpoint and check timing margin across the intended temperature range.
Do not treat the 5.5 V input tolerance as permission to operate two incompatible logic domains through the PCA9521D. The device buffers signals within a common low-voltage domain and does not perform voltage translation. Also avoid assuming that a part in the same SOP-8 package is a drop-in replacement: confirm every pin, supply range, direction behavior, capacitance rating, and bus timing requirement before substitution.
تعمیل کی معلومات
The available product information does not provide a definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement. The component is an industrial-temperature interface IC rather than an automotive-qualified device.