PCA9555PWE4 - 16-Bit 400kHz I/O Expander | Texas Instruments
MPN: PCA9555PWE4 ✓ نشطPCA9555PWE4 نظرة عامة
An I/O expander is an interface IC that extends the number of controllable or readable digital lines available on a microcontroller or embedded processor. The PCA9555 belongs to the broader hierarchy of I2C interface controllers, peripheral interface ICs, and semiconductors. Its two 8-bit ports can be configured independently as inputs or outputs, while power-on reset and configuration registers establish the initial operating state.
The key feature set includes 16 configurable I/O lines, a 2.3V to 5.5V supply range, a 400kHz I2C interface, an interrupt output, configuration registers, and weak pull-ups. The interrupt output allows the host to detect a change on an input port without continuously polling the device. This combination reduces host pin count and can simplify firmware event handling in distributed control systems.
The PCA9555 registers port direction, polarity, and output data through the serial interface. Input port values reflect the corresponding input pins, while output port values control the output pins. Reset initializes the ports to their default state, giving the host a defined starting condition. The device also supports multiple fixed slave addresses, allowing separate expanders to share the same SDA and SCL bus when address straps are configured appropriately.
Typical uses include industrial control modules, automated test equipment, appliance interfaces, LED control, keyboard or switch sensing, and general-purpose embedded I/O. The 24-TSSOP package keeps the device practical for compact controller boards, while its 2.3V to 5.5V operating range accommodates both 3.3V and 5V systems. Industrial-temperature operation extends suitability across factory, building, and instrumentation equipment.
PCB design should keep SDA, SCL, and ground connections short, place pull-up resistors close to the bus master, and account for bus capacitance when choosing their values. Confirm address selection before routing multiple expanders on one bus, and use the interrupt line when change-driven updates are preferable to periodic polling. The 24-pin footprint requires careful TSSOP pad spacing and adequate clearance during assembly.
This product page combines the device functions, interface limits, package details, candidate drop-in alternatives, and implementation guidance needed to evaluate the PCA9555PWE4 for an existing embedded design.
بدائل مباشرة لـ PCA9555PWE4 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع PCA9555PWE4 (نفس عامل الشكل والبصمة) — يختلف في Configuration Registers, Interrupt Output, Package.
XRA1201PIG24TR-F
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TCA9555PWR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←PCA9555PWE4 المواصفات
| Number of I/O Ports | 16 I/O |
| نوع الواجهة | I2C and SMBus |
| Maximum I2C Clock Frequency | 400 kHz |
| Supply Voltage Range | 2.3V to 5.5V |
| Port Configuration | 2 independent 8-bit input or output ports |
| Interrupt Output | 1 open-drain interrupt output |
| Configuration Registers | Present |
| Power-On Reset | Present |
| Weak Pull-Ups | Weak pull-ups on I/O ports |
| نطاق درجة حرارة التشغيل | -40°C to +85°C |
| Temperature Grade | Industrial |
| العلبة | 24-pin TSSOP |
| Package Width | 4.40 mm |
| Terminal Form | Gull wing |
| نوع التركيب | Surface mount |
| Datasheet Length | 35 pages |
| I2C Slave Addresses | 8 fixed addresses |
دليل تكوين أطراف PCA9555PWE4 4.40 mm
تكوين الأطراف لـ PCA9555PWE4 (حزمة 4.40 mm). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ PCA9555PWE4.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
PCA9555PWE4 مناسب لـ 6 التطبيقs: Industrial Control and Automation, LED and Indicator Control, Appliance and User Interface Control, Keyboard and Switch Matrix, Automated Test Equipment, Building and Sensor Interface Modules.
Industrial Control and Automation
The PCA9555PWE4 fits industrial control boards that need more digital lines than the host controller can expose directly. Its 16 configurable ports can monitor limit switches, door sensors, and machine-state lines while driving alarm or status indicators. Operating from 2.3V to 5.5V supports common 24V industrial control architectures when the interface is conditioned appropriately, while the -40°C to +85°C range covers industrial equipment. Place the device between the controller and field logic, configure direction and polarity registers during startup, and use the interrupt output for change-driven handling instead of unnecessary continuous polling.
موصى به
LED and Indicator Control
The PCA9555PWE4 is useful when a controller must drive more LEDs or digital indicators than available GPIO pins. Its two 8-bit output ports provide 16 individually controlled lines with latched output data and configurable polarity. The 400kHz serial interface updates the output register quickly enough for ordinary status and illumination patterns, while the 2.3V-to-5.5V range allows the expander to operate beside either 3.3V or 5V logic. Account for LED current, series resistance, and any common-anode or common-cathode arrangement; the PCA9555 itself controls logic levels and does not provide constant-current LED regulation.
موصى به
Appliance and User Interface Control
The PCA9555PWE4 can connect buttons, selectors, alarm lamps, and other panel signals to a compact appliance controller without consuming many host GPIO pins. Inputs may be configured as either input or output on each 8-bit port, allowing status reads and controlled outputs within the same device. The interrupt capability lets the controller react to a user action rather than polling every loop. Its 24-pin TSSOP footprint is compact, and the 2.3V-to-5.5V supply range supports multiple logic levels. Firmware should define a safe reset state, configure polarity for switch wiring, and debounce any mechanical contacts in software or with suitable external components.
موصى به
Keyboard and Switch Matrix
The PCA9555PWE4 is appropriate for reading additional switches, keypads, selectors, or interlocks through two 8-bit ports. Its 16 input lines can replace direct host GPIO connections, and the interrupt output allows the firmware to identify relevant changes efficiently. Operating at up to 400kHz supports regular register-based input polling and event handling. The open-drain interrupt can be shared or managed according to the bus design, while pull-up strength and bus capacitance should be checked in the final circuit. For debouncing, use appropriate hardware or firmware timing and preserve the configured input polarity across resets to avoid false event indications.
موصى به
Automated Test Equipment
The PCA9555PWE4 can expand fixture-control and instrument-interface lines in automated test equipment. Sixteen configurable I/O pins can sequence relay-control signals, connect test points, monitor equipment status, or read fixture sensors. The interrupt output reduces unnecessary serial reads when a monitored line changes, which is useful in repeated test cycles. The 2.3V-to-5.5V range accommodates common control voltages, and the 24-TSSOP package preserves board area. Define fail-safe output states, account for relay-coil current and flyback paths, and keep the I2C traces away from high-switching-current paths to reduce noise coupling into the interface.
Building and Sensor Interface Modules
The PCA9555PWE4 works well in distributed building-control or sensor-interface modules that aggregate several binary inputs and outputs over a short I2C bus. Sensors can report door, occupancy, alarm, or equipment-status conditions through eight-bit groups, while output ports control indicators or low-current interface signals. The interrupt output helps a building controller respond promptly to a selected event, and the 400kHz bus rate is sufficient for ordinary supervisory control traffic. Use fixed address selection when multiple modules share SDA and SCL, ensure pull-ups support the total bus capacitance, and maintain suitable separation from motors, relays, or switching power stages.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ PCA9555PWE4 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | XRA1201PIG24TR-F | TCA9555PWR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | NXP |
| Package | 24-pin TSSOP | 24-pin TSSOP | 24-pin TSSOP |
| Minimum Supply Voltage | 2.3V | 2.3V | 1.65V |
| Maximum Supply Voltage | 5.5V | 3.6V for stated drop-in use | 5.5V |
| Interface | I2C and SMBus | Pin and software compatible with PCA9555 | I2C |
أبرز الفروقات
- Supports the full PCA9555 5V operating range (مقابلXRA1201PIG24TR-F)
- Provides a broader low-voltage supply range than the target (مقابلTCA9555PWR)
- Established PCA9555 register and software compatibility (مقابلTCA9555PWR)
ملاحظات التصميم
Route SDA, SCL, VCC, and ground as short, continuous paths, and place the bus pull-up resistors near the master or at the location specified by the system bus architecture. TSSOP lead spacing is narrow, so verify the PCB land pattern against the package drawing and use a paste stencil and assembly process suitable for 0.65mm-pitch devices.
Do not assume that identical TSSOP packages guarantee drop-in operation. Before substituting the XRA1201PIG24TR-F or TCA9555PWR, compare slave-address straps, direction and polarity register positions, reset behavior, interrupt polarity, electrical limits, and driver compatibility. The XRA1201 cross-reference specifically limits drop-in use to 2.3V-to-3.6V operation.
Check each I/O pin against the PCA9555's absolute-maximum and output-current limits before driving LEDs, relay drivers, or other non-floating loads. The PCA9555 provides digital logic rather than constant-current LED drive or relay-driver functions. External buffers or drivers may be required when a port must source or sink current beyond the device's rated operating conditions.
Keep the interrupt trace away from noisy switching nodes and preserve a clear return path beneath the serial interface. If the expander is mounted near relays, motors, or power converters, route SDA and SCL away from high-current paths and evaluate whether additional filtering or shielding is needed. This helps preserve the integrity of register reads in electrically noisy equipment.
معلومات الامتثال
The industrial temperature grade and surface-mount construction are documented, but specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the cited product information.