Texas Instruments

PCA9555PWE4 - 16-Bit 400kHz I/O Expander | Texas Instruments

部品番号: PCA9555PWE4 ✓ 生産中
2.3V to 5.5V Vdss 24-pin TSSOP Package 400 kHz Speed
MOQ: 1 |

PCA9555PWE4 概要

The Texas Instruments PCA9555PWE4 is a 16-bit I2C and SMBus I/O expander operating from 2.3V to 5.5V at up to 400kHz, with an interrupt output and configuration registers in a 24-pin TSSOP package. It adds 16 general-purpose digital input or output ports to a host processor through the two-wire serial bus.

An I/O expander is an interface IC that extends the number of controllable or readable digital lines available on a microcontroller or embedded processor. The PCA9555 belongs to the broader hierarchy of I2C interface controllers, peripheral interface ICs, and semiconductors. Its two 8-bit ports can be configured independently as inputs or outputs, while power-on reset and configuration registers establish the initial operating state.

The key feature set includes 16 configurable I/O lines, a 2.3V to 5.5V supply range, a 400kHz I2C interface, an interrupt output, configuration registers, and weak pull-ups. The interrupt output allows the host to detect a change on an input port without continuously polling the device. This combination reduces host pin count and can simplify firmware event handling in distributed control systems.

The PCA9555 registers port direction, polarity, and output data through the serial interface. Input port values reflect the corresponding input pins, while output port values control the output pins. Reset initializes the ports to their default state, giving the host a defined starting condition. The device also supports multiple fixed slave addresses, allowing separate expanders to share the same SDA and SCL bus when address straps are configured appropriately.

Typical uses include industrial control modules, automated test equipment, appliance interfaces, LED control, keyboard or switch sensing, and general-purpose embedded I/O. The 24-TSSOP package keeps the device practical for compact controller boards, while its 2.3V to 5.5V operating range accommodates both 3.3V and 5V systems. Industrial-temperature operation extends suitability across factory, building, and instrumentation equipment.

PCB design should keep SDA, SCL, and ground connections short, place pull-up resistors close to the bus master, and account for bus capacitance when choosing their values. Confirm address selection before routing multiple expanders on one bus, and use the interrupt line when change-driven updates are preferable to periodic polling. The 24-pin footprint requires careful TSSOP pad spacing and adequate clearance during assembly.

This product page combines the device functions, interface limits, package details, candidate drop-in alternatives, and implementation guidance needed to evaluate the PCA9555PWE4 for an existing embedded design.

ドロップイン代替品: PCA9555PWE4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: PCA9555PWE4 (同一形状・フットプリント) — 相違点: Configuration Registers, Interrupt Output, Package.

Texas Instruments
Configuration Registers: Yes (direction, polarity, mask)
Interrupt Output: Yes, active-low open-drain INT
Package: 24-pin TSSOP (PW)
比較対象 PCA9555PWE4 →

XRA1201PIG24TR-F

✅ ドロップイン
📦 24-TSSOP
Pin and software compatible with PCA9555, but the cross-reference limits drop-in use to 2.3V-3.6V rather than the PCA9555's 2.3V-5.5V range.

📋 参考代替品(カタログ未掲載)

TCA9555PWR

✅ ドロップイン
Texas Instruments
📦 24-TSSOP
16-bit I2C/SMBus I/O expander · 16 · I2C, SMBus · 400 kHz (TI) / 1 MHz (UMW second-source) · 3 (A0, A1, A2) - up to 8 devices per bus · Yes, active-low open-drain INT · Yes (direction, polarity, mask) · Programmable per port

価格はお問い合わせください

データシートを見る →

PCA9555PWE4 仕様

Number of I/O Ports 16 I/O
インターフェースタイプ I2C and SMBus
Maximum I2C Clock Frequency 400 kHz
Supply Voltage Range 2.3V to 5.5V
Port Configuration 2 independent 8-bit input or output ports
Interrupt Output 1 open-drain interrupt output
Configuration Registers Present
Power-On Reset Present
Weak Pull-Ups Weak pull-ups on I/O ports
動作温度範囲 -40°C to +85°C
Temperature Grade Industrial
パッケージ 24-pin TSSOP
Package Width 4.40 mm
Terminal Form Gull wing
実装タイプ Surface mount
Datasheet Length 35 pages
I2C Slave Addresses 8 fixed addresses

PCA9555PWE4 4.40 mm ピン配置ガイド

PCA9555PWE4 (4.40 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。

PCA9555PWE4 の 4.40 mm パッケージピン配置図

詳細なピン配置データはありません: PCA9555PWE4.

詳細は データシート をご参照ください。

主な用途

PCA9555PWE4 の用途: 6 件s: Industrial Control and Automation, LED and Indicator Control, Appliance and User Interface Control, Keyboard and Switch Matrix, Automated Test Equipment, Building and Sensor Interface Modules.

🏭

Industrial Control and Automation

The PCA9555PWE4 fits industrial control boards that need more digital lines than the host controller can expose directly. Its 16 configurable ports can monitor limit switches, door sensors, and machine-state lines while driving alarm or status indicators. Operating from 2.3V to 5.5V supports common 24V industrial control architectures when the interface is conditioned appropriately, while the -40°C to +85°C range covers industrial equipment. Place the device between the controller and field logic, configure direction and polarity registers during startup, and use the interrupt output for change-driven handling instead of unnecessary continuous polling.

💡

LED and Indicator Control

The PCA9555PWE4 is useful when a controller must drive more LEDs or digital indicators than available GPIO pins. Its two 8-bit output ports provide 16 individually controlled lines with latched output data and configurable polarity. The 400kHz serial interface updates the output register quickly enough for ordinary status and illumination patterns, while the 2.3V-to-5.5V range allows the expander to operate beside either 3.3V or 5V logic. Account for LED current, series resistance, and any common-anode or common-cathode arrangement; the PCA9555 itself controls logic levels and does not provide constant-current LED regulation.

🔧

Appliance and User Interface Control

The PCA9555PWE4 can connect buttons, selectors, alarm lamps, and other panel signals to a compact appliance controller without consuming many host GPIO pins. Inputs may be configured as either input or output on each 8-bit port, allowing status reads and controlled outputs within the same device. The interrupt capability lets the controller react to a user action rather than polling every loop. Its 24-pin TSSOP footprint is compact, and the 2.3V-to-5.5V supply range supports multiple logic levels. Firmware should define a safe reset state, configure polarity for switch wiring, and debounce any mechanical contacts in software or with suitable external components.

🔧

Keyboard and Switch Matrix

The PCA9555PWE4 is appropriate for reading additional switches, keypads, selectors, or interlocks through two 8-bit ports. Its 16 input lines can replace direct host GPIO connections, and the interrupt output allows the firmware to identify relevant changes efficiently. Operating at up to 400kHz supports regular register-based input polling and event handling. The open-drain interrupt can be shared or managed according to the bus design, while pull-up strength and bus capacitance should be checked in the final circuit. For debouncing, use appropriate hardware or firmware timing and preserve the configured input polarity across resets to avoid false event indications.

🔧

Automated Test Equipment

The PCA9555PWE4 can expand fixture-control and instrument-interface lines in automated test equipment. Sixteen configurable I/O pins can sequence relay-control signals, connect test points, monitor equipment status, or read fixture sensors. The interrupt output reduces unnecessary serial reads when a monitored line changes, which is useful in repeated test cycles. The 2.3V-to-5.5V range accommodates common control voltages, and the 24-TSSOP package preserves board area. Define fail-safe output states, account for relay-coil current and flyback paths, and keep the I2C traces away from high-switching-current paths to reduce noise coupling into the interface.

🧩

Building and Sensor Interface Modules

The PCA9555PWE4 works well in distributed building-control or sensor-interface modules that aggregate several binary inputs and outputs over a short I2C bus. Sensors can report door, occupancy, alarm, or equipment-status conditions through eight-bit groups, while output ports control indicators or low-current interface signals. The interrupt output helps a building controller respond promptly to a selected event, and the 400kHz bus rate is sufficient for ordinary supervisory control traffic. Use fixed address selection when multiple modules share SDA and SCL, ensure pull-ups support the total bus capacitance, and maintain suitable separation from motors, relays, or switching power stages.

What is the operating voltage of PCA9555PWE4?
The PCA9555PWE4 operates from 2.3V to 5.5V, making it suitable for both 3.3V and 5V embedded systems. According to the Texas Instruments PCA9555 datasheet, the device contains 16 configurable digital I/O lines organized as two 8-bit ports. It communicates with a host processor through an I2C or SMBus-compatible two-wire interface and supports operation up to 400kHz.
How many I/O pins does the PCA9555PWE4 provide?
The PCA9555PWE4 provides 16 digital I/O pins divided into two 8-bit ports, and each port can be configured as input or output. The Texas Instruments datasheet identifies separate direction, polarity, and output-data registers. This lets one connected device implement mixed input and output functions while conserving microcontroller pins and reducing repetitive serial-bus traffic.
What is the maximum I2C clock frequency of PCA9555PWE4?
The PCA9555PWE4 supports I2C communication at up to 400kHz. The 400kHz operating point is stated for the PCA9555 family by Texas Instruments and is also identified in the product listing. Designers should still verify the complete bus timing against the host controller, pull-up resistance, bus capacitance, and any other devices attached to the same SDA and SCL lines.
What functions are available on PCA9555PWE4?
The PCA9555PWE4 combines 16 configurable digital I/O lines, an open-drain interrupt output, power-on reset behavior, and configuration registers in one 24-TSSOP device. According to the Texas Instruments datasheet, the two 8-bit ports support independent input or output direction. The interrupt output can signal a change at an input port, allowing the host to respond without continuously polling the expander.
Where can I download the PCA9555PWE4 datasheet PDF?
The official PCA9555PWE4 datasheet is available through the Texas Instruments literature link at https://www.ti.com/lit/ds/symlink/pca9555.pdf. It contains the pin configuration, register map, electrical characteristics, timing information, and application details needed for PCB and firmware design. Use the manufacturer document when assigning signals because generic I/O-expander documents may describe different pin assignments or reset behavior.
Where is the pinout for PCA9555PWE4?
The PCA9555PWE4 pinout is documented in the Texas Instruments datasheet and corresponds to its 24-pin TSSOP package. It includes the two serial-bus pins, supply and ground connections, 16 port I/O pins, reset, and interrupt functions. Assign PCB nets directly from the manufacturer pin-description table so that the orientation marker, exposed pad conditions, and alternate-function details are followed exactly.
What can replace PCA9555PWE4 as a drop-in part?
The XRA1201PIG24TR-F from Texas Instruments is identified as a pin-compatible functional equivalent, while the NXP TCA9555PWR is a candidate 24-pin I/O-expander substitute. A replacement should still be checked for address mapping, register behavior, reset timing, electrical limits, and interrupt polarity. The MaxLinear cross-reference specifically describes the XRA1201 as suitable for drop-in use in 2.3V to 3.6V systems.
Is XRA1201PIG24TR-F pin-compatible with PCA9555PWE4?
The XRA1201PIG24TR-F is reported as pin and software compatible with the PCA9555, but the stated drop-in operating range is narrower at 2.3V to 3.6V. The MaxLinear cross-reference therefore treats it as a possible replacement rather than an unrestricted equivalent. Confirm the 2.3V-to-5.5V operating requirement of the PCA9555 design against the XRA1201 limits before approving the substitution.
Is PCA9555PWE4 suitable for a 5V industrial controller?
Yes, the PCA9555PWE4 is suitable for a 5V controller because its stated supply range of 2.3V to 5.5V includes 5V. Its industrial temperature grade covers -40°C to +85°C, and its 400kHz serial interface is appropriate for moderate-rate control and monitoring tasks. Verify I/O levels, pull-up voltage, bus loading, and input tolerances against the connected circuitry before deployment.
PCA9555PWE4 vs TCA9555PWR: which is better for a 5V system?
The PCA9555PWE4 is the stronger choice when a design specifically requires the established Texas Instruments PCA9555 behavior, a 2.3V minimum supply, and operation up to 5.5V. The NXP TCA9555PWR also provides 16 I/O lines in a 24-TSSOP package and supports 1.65V to 5.5V, but register behavior, addressing, and electrical details should be compared before treating it as interchangeable.
When should I choose PCA9555PWE4 over another 16-bit I/O expander?
Choose the PCA9555PWE4 when the design needs 16 independently configurable digital lines, a 2.3V-to-5.5V operating range, 400kHz I2C operation, and a documented interrupt output in a 24-pin TSSOP package. It is especially useful when preserving an existing PCA9555 software driver or PCB layout is more important than accepting a wider supply range or a different register implementation from another manufacturer.
Is TCA9555PWR a drop-in replacement for PCA9555PWE4?
The TCA9555PWR is a potential 24-TSSOP replacement, but it should not be approved as a drop-in solely from package matching. The comparison information identifies both devices as 16-bit I2C I/O expanders, while the TCA9555PWR supports a lower minimum supply of 1.65V. Validate pin functions, slave-address selection, configuration registers, interrupt behavior, timing, and the maximum output current before releasing the substitution.
How do I configure the PCA9555PWE4 interrupt output?
The PCA9555PWE4 can use its interrupt output to report an input-port state change, reducing the need for continuous polling. The host first writes the port direction and polarity registers, then enables the interrupt function through the appropriate configuration bits in the control register. Use the Texas Instruments register table to confirm the exact masks and bit positions before writing device software.
What are the key specifications of PCA9555PWE4 that engineers should know?
The principal PCA9555PWE4 specifications are 16 configurable I/O lines, a 2.3V-to-5.5V supply range, operation up to 400kHz, an open-drain interrupt output, configuration registers, and a 24-pin TSSOP package. The device also supports an industrial temperature range of -40°C to +85°C. These characteristics place it between a host MCU and external buttons, indicators, relays, or other digital circuitry.
Where can I buy PCA9555PWE4 and check its lead time?
Use the Request a Quote form on this page to request PCA9555PWE4 pricing, current inventory, minimum order quantity, and production lead time. The commercial team can confirm the exact 24-TSSOP ordering code and shipment schedule. Because availability and delivery timing can change, request the current commitment rather than relying on a historical stock indication or an archived unit price.

エンジニアリング参考データ: PCA9555PWE4 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the PCA9555PWE4 for a 24-pin TSSOP design requiring 16 configurable digital I/O lines, a 2.3V-to-5.5V supply range, 400kHz I2C communication, an interrupt output, and PCA9555-compatible software behavior. Choose XRA1201PIG24TR-F when the board operates only between 2.3V and 3.6V and a Texas Instruments pin- and software-compatible alternative is desired. Choose TCA9555PWR when operation below 2.3V is required or when its register and electrical characteristics have already been validated for the application. For every candidate, verify the exact pin functions, fixed-address strapping, reset sequence, interrupt polarity, input thresholds, output-current limits, and package dimensions. The PCA9555PWE4 is generally the lowest-risk choice for preserving an existing 5V PCA9555 design because no logic-level or software adaptation is needed.

代替品との比較

パラメータ この製品 XRA1201PIG24TR-F TCA9555PWR
Brand Texas Instruments Texas Instruments NXP
Package 24-pin TSSOP 24-pin TSSOP 24-pin TSSOP
Minimum Supply Voltage 2.3V 2.3V 1.65V
Maximum Supply Voltage 5.5V 3.6V for stated drop-in use 5.5V
Interface I2C and SMBus Pin and software compatible with PCA9555 I2C

主な差別化要因

  • Supports the full PCA9555 5V operating range (vs XRA1201PIG24TR-F)
  • Provides a broader low-voltage supply range than the target (vs TCA9555PWR)
  • Established PCA9555 register and software compatibility (vs TCA9555PWR)

設計ノート

Route SDA, SCL, VCC, and ground as short, continuous paths, and place the bus pull-up resistors near the master or at the location specified by the system bus architecture. TSSOP lead spacing is narrow, so verify the PCB land pattern against the package drawing and use a paste stencil and assembly process suitable for 0.65mm-pitch devices.

Do not assume that identical TSSOP packages guarantee drop-in operation. Before substituting the XRA1201PIG24TR-F or TCA9555PWR, compare slave-address straps, direction and polarity register positions, reset behavior, interrupt polarity, electrical limits, and driver compatibility. The XRA1201 cross-reference specifically limits drop-in use to 2.3V-to-3.6V operation.

Check each I/O pin against the PCA9555's absolute-maximum and output-current limits before driving LEDs, relay drivers, or other non-floating loads. The PCA9555 provides digital logic rather than constant-current LED drive or relay-driver functions. External buffers or drivers may be required when a port must source or sink current beyond the device's rated operating conditions.

Keep the interrupt trace away from noisy switching nodes and preserve a clear return path beneath the serial interface. If the expander is mounted near relays, motors, or power converters, route SDA and SCL away from high-current paths and evaluate whether additional filtering or shielding is needed. This helps preserve the integrity of register reads in electrically noisy equipment.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The industrial temperature grade and surface-mount construction are documented, but specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the cited product information.

データ検証日: 2026-11-14 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

PCA9555PWE4 datasheet PCA9555PWE4 pinout PCA9555PWE4 datasheet pdf PCA9555PWE4 equivalent PCA9555PWE4 replacement PCA9555PWE4 cross reference PCA9555PWE4 TSSOP-24 footprint PCA9555PWE4 16-bit I/O expander PCA9555PWE4 400kHz I2C PCA9555PWE4 vs TCA9555PWR PCA9555PWE4 price PCA9555PWE4 stock Texas Instruments PCA9555PWE4 PCA9555PWE4 application circuit What can replace PCA9555PWE4?

関連部品&用語

Texas Instruments PCA9555PWE4 XRA1201PIG24TR-F TCA9555PWR PCA9555 16-bit I/O expander I/O expander I2C SMBus general-purpose I/O two-wire serial bus interrupt output configuration register power-on reset 2.3V to 5.5V 400kHz TSSOP-24 TSSOP package family surface-mount technology industrial control LED control automated test equipment weak pull-up open-drain interrupt
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示