إشعار الشراء الأخير: PCA9672D يقترب من نهاية العمر الإنتاجي. آخر موعد للطلب: تواصل معنا. عرض القطع البديلة المتاحة →
NXP Semiconductors

PCA9672D - 8-Bit I/O Expander with 1 MHz I2C | NXP

MPN: PCA9672D ✗ انتهى عمره الإنتاجي
2.3 V to 5.5 V Vdss 16-pin SO package Package 1 MHz Fast-mode Plus (Fm+) Speed
الحد الأدنى للطلب: 1 |

PCA9672D نظرة عامة

NXP Semiconductors PCA9672D is an 8-bit remote I/O expander with a 1 MHz I2C Fast-mode Plus interface, operating from 2.3 V to 5.5 V. The device provides eight quasi-bidirectional GPIO ports, three hardware address inputs, an interrupt output, and a reset input in a 16-pin SO package.

An I/O expander is an interface IC that adds parallel digital input or output capability to a host controller over a serial bus. In the product hierarchy, the PCA9672D is an I/O expander within interface ICs and semiconductors. Its two-wire I2C connection reduces the number of host-controller pins required when a design needs additional control, status, or general-purpose I/O lines.

The principal features include eight quasi-bidirectional ports, I2C Fast-mode Plus operation up to 1 MHz, three hardware address inputs, an interrupt output, and a reset input. The 2.3 V to 5.5 V operating range permits use in both 3.3 V and 5 V systems. Quasi-bidirectional ports can be configured individually as inputs or outputs, allowing the same external connector or control interface to combine input and output signals.

The PCA9672D supports both interrupt-driven and polling-based host communication. An output port can generate an interrupt when a connected input changes state, allowing the host to handle events without continuously polling all eight inputs. The reset input provides a defined recovery path for the serial interface and port state. I2C address selection through three hardware address inputs permits multiple expanders on the same bus when their address straps are assigned differently.

Typical uses include LED status and control panels, keypad and switch interfaces, industrial automation modules, sensor gathering, alarm and monitoring equipment, and compact embedded control boards. The 1 MHz bus rate is particularly useful for LED dimming or moderate-rate control traffic, while the interrupt output improves responsiveness in event-driven systems.

Designers should verify the electrical characteristics of each quasi-bidirectional port, including its output-current capability and pull-up arrangement, before driving loads. The PCB layout should keep the I2C traces short, provide continuous ground references, and place bypass and pull-up components close to their associated pins. Firmware must also define startup states to avoid unintended outputs during reset.

This product page combines the manufacturer feature summary, package identification, lifecycle information, ordering-code details, and practical guidance for I2C expansion, event handling, reset behavior, and PCB implementation. It also distinguishes exact ordering variants from unrelated interface ICs that use similar functions but do not share the same package and pin arrangement.

بدائل مباشرة لـ PCA9672D — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

PCA9672D,512

✅ بديل مباشر
📦 16-pin SO
Same PCA9672 device function and 16-pin SO electrical configuration; -512 is the ordering suffix, so voltage, I/O count, 1 MHz I2C speed, and 2.3 V to 5.5 V range are unchanged.

📋 بديل مرجعي (غير موجود في الكتالوج)

PCA9672D المواصفات

Device Type 8-bit remote I/O expander
Number of I/O Ports 8 ports
Port Type Quasi-bidirectional
Serial Interface I2C two-wire bidirectional bus
I2C Bus Frequency 1 MHz Fast-mode Plus (Fm+)
I2C Interface Drive Capability 30 mA
Operating Voltage Range 2.3 V to 5.5 V
Hardware Address Inputs 3 inputs
Interrupt Output 1 open-drain interrupt output
Reset Input 1 active-low reset input
العلبة 16-pin SO package
نوع التركيب Surface mount

دليل تكوين أطراف PCA9672D 16-pin so package

تكوين الأطراف لـ PCA9672D (حزمة 16-pin so package). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 16-pin so package لـ PCA9672D

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ PCA9672D.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

PCA9672D مناسب لـ 6 التطبيقs: LED Status and Dimming Panel, Industrial Switch and Keypad Interface, Sensor and Alarm Input Aggregation, Remote Control and Relay Interface, Automated Test and Measurement Front End, Embedded Access and Security Control.

💡

LED Status and Dimming Panel

The PCA9672D fits an LED status panel because its eight quasi-bidirectional ports can drive or sense multiple indicator channels while the host communicates through I2C. Fast-mode Plus operation up to 1 MHz permits efficient register updates, and the interrupt output can notify the controller when an externally monitored input changes. The 2.3 V to 5.5 V range supports both 3.3 V and 5 V logic systems. For PWM dimming, confirm the port current limit and use suitable transistor stages when an LED string exceeds the direct-drive capability. The design should also define each port's reset state so the panel does not illuminate unexpectedly during startup.

🏭

Industrial Switch and Keypad Interface

The PCA9672D can consolidate switch, keypad, or selector inputs into an embedded controller without dedicating eight host GPIO pins. Its eight quasi-bidirectional ports support mixed input and output use, while three hardware address inputs allow multiple expanders to coexist on one I2C bus with distinct addresses. The interrupt output reduces the need for continuous polling when a human-operated control changes state. In an industrial module, place the I2C pull-ups and bypass capacitor close to the device and keep the bus away from switching-node traces. Firmware should debounce mechanical contacts and confirm the exact port behavior in the manufacturer datasheet before finalizing the input circuit.

🧩

Sensor and Alarm Input Aggregation

The PCA9672D is useful for collecting several discrete sensor, alarm, or interlock signals through one two-wire interface. The host reads port states over I2C, and the interrupt output can signal a change so the controller can respond without continuously polling. Three hardware address inputs allow several expansion devices to be placed on the same bus when each receives a unique address configuration. Because the ports are quasi-bidirectional rather than dedicated high-current inputs, the external sensor must be compatible with the port's pull-up and input characteristics. The 2.3 V to 5.5 V operating range also helps align the expander with many industrial embedded controllers, subject to the device's temperature and EMC requirements.

⚡

Remote Control and Relay Interface

The PCA9672D can serve as the low-voltage control layer for a remote relay or switch bank. Eight outputs allow a host to activate and monitor multiple channels through I2C, reducing wiring compared with individual host-controller lines. For inductive or high-current loads, use suitable driver transistors or relay interfaces rather than driving the loads directly from the expander. The interrupt output can support feedback or change detection when a monitored line is connected to a port. The 1 MHz Fast-mode Plus interface helps the host update multiple channels efficiently, while the reset input offers a defined startup path. Production firmware should leave outputs in a safe inactive state until the host has initialized the device and validated the external circuitry.

🖥️

Automated Test and Measurement Front End

The PCA9672D can extend a test-and-measurement controller with eight quasi-bidirectional lines for fixture control, status lamps, or discrete instrumentation signals. The I2C interface allows the host to update these lines over a compact two-wire connection, and Fast-mode Plus operation up to 1 MHz supports responsive fixture sequencing. A hardware interrupt can indicate a change on an input connected to the fixture, which is useful for asynchronous equipment events. The device's 2.3 V to 5.5 V range supports common laboratory and embedded logic levels. Keep sensitive analog and high-impedance measurement paths separate from the digital bus, use short ground returns, and check every port's electrical limit against the fixture before reducing resistance or changing logic levels.

🔒

Embedded Access and Security Control

The PCA9672D can support compact access-control hardware by connecting keypad lines, door-status inputs, indicator outputs, and local request signals to one I2C host interface. Three hardware address inputs permit several expansion devices to share a bus, and the interrupt output allows the controller to react promptly to a door or request event. The 2.3 V to 5.5 V operating range accommodates common embedded supply levels. Because security systems often contain long wiring runs, add appropriate input conditioning and protection rather than relying on the expander alone for surge or ESD protection. During reset, explicitly configure outputs to prevent unintended unlocks or alarm indications, and review the final pin assignments against the NXP datasheet before fabrication.

ملخص المنتجات الموصى بها

PCA9672D NXP Semiconductors يُستخدم في: LED Status and Dimming Panel, Industrial Switch and Keypad Interface, Sensor and Alarm Input Aggregation, Remote Control and Relay Interface, Automated Test and Measurement Front End, Embedded Access and Security Control PCA9672D,512 Orderable PCA9672D packaging variant يُستخدم في: LED Status and Dimming Panel, Industrial Switch and Keypad Interface, Sensor and Alarm Input Aggregation, Remote Control and Relay Interface, Automated Test and Measurement Front End, Embedded Access and Security Control
What is the PCA9672D?
The PCA9672D is an 8-bit remote I/O expander from NXP Semiconductors that connects eight quasi-bidirectional GPIO ports to a host through an I2C bus. According to the NXP product summary, it supports I2C Fast-mode Plus operation to 1 MHz, three hardware address inputs, an interrupt output, and a reset input over a 2.3 V to 5.5 V supply range.
What is the operating voltage of the PCA9672D?
The PCA9672D operates from 2.3 V to 5.5 V. The NXP product summary identifies this supply range while also confirming support for a 1 MHz I2C Fast-mode Plus interface. This makes the device suitable for common 3.3 V and 5 V embedded systems, although each connected port and the I2C pull-ups must remain within their own electrical limits.
How many I/O ports does the PCA9672D provide?
The PCA9672D provides eight quasi-bidirectional I/O ports. NXP describes these as general-purpose ports that can be configured for input or output operation, allowing a single device to collect switch or sensor states and also control external loads. Port direction is established through the device register interface after reset.
Where can I download the PCA9672D datasheet PDF?
The official PCA9672D datasheet is available through the NXP product page linked on this page. The NXP page also identifies the device as no longer manufactured and provides its technical feature summary. Use the manufacturer datasheet for the authoritative pin-description table, port electrical limits, timing diagrams, and recommended application circuit before assigning PCB tracks.
Where can I find the PCA9672D pinout?
The PCA9672D pinout is documented in the pin-description table of the NXP manufacturer datasheet. The device uses a 16-pin SO package, but individual pin numbers and signal names are not reproduced on this page because they require direct confirmation against the package drawing. Use the datasheet table together with the selected package footprint when creating the schematic and PCB layout.
Can the PCA9672D drive LEDs at 1 MHz I2C speed?
Yes, the PCA9672D is suitable for LED dimming and control applications because its I2C interface supports Fast-mode Plus operation up to 1 MHz. The interface rate accelerates register access and output updates, but actual LED brightness performance also depends on the chosen PWM method, port drive limits, external transistor topology, and the load presented by each LED circuit.
PCA9672D versus PCA9534ARGVRG4: which is better for a new design?
The PCA9672D is preferable when an existing board requires its 16-pin SO footprint, 1 MHz I2C interface, and three hardware address inputs. The PCA9534ARGVRG4 is a different package and interface device, so it is not a direct PCB drop-in replacement. The correct choice depends on package compatibility, bus speed, addressing requirements, port architecture, and availability rather than GPIO count alone.
What is the difference between the PCA9672D and PCA9672D,512?
PCA9672D,512 is the orderable packaging suffix used for the NXP PCA9672D device, while PCA9672D is the base device identifier used for family-level searches. They represent the same PCA9672 function and 16-pin SO configuration rather than different electrical designs. The -512 ordering code should be matched exactly when checking stock, reel packaging, or manufacturing traceability.
When should I choose the PCA9672D instead of a generic 8-bit I/O expander?
Choose the PCA9672D when the design needs eight quasi-bidirectional ports, I2C Fast-mode Plus operation to 1 MHz, three hardware address inputs, and a dedicated interrupt output in the 16-pin SO package. A generic expander may offer a similar GPIO count, but it may use a slower bus, different addressing method, or different package. Confirm the complete pin function and electrical limits before substitution.
Is the PCA9672D suitable for an industrial control module?
The PCA9672D is functionally suitable for industrial control modules that use a 3.3 V or 5 V I2C bus and need additional control or status lines. Its 2.3 V to 5.5 V operating range, 1 MHz Fast-mode Plus interface, reset input, and interrupt output support robust embedded communication. Industrial suitability still depends on the device's specified temperature grade, isolation, surge exposure, and system-level EMC requirements.
What can replace the PCA9672D on the same PCB?
The only directly supported ordering variant identified for the same device is PCA9672D,512, which uses the same PCA9672 function and package rather than providing a different competitor design. A separate manufacturer part should not be treated as a drop-in replacement unless its datasheet confirms identical pinout, electrical behavior, address scheme, and package. Request a cross-reference review when the original package or function has changed.
Where can I buy the PCA9672D and check the current lead time?
Use the Request a Quote form on this page to ask for the exact PCA9672D ordering code, current availability, lead time, and minimum order quantity. NXP identifies the base device as no longer manufactured, so lifecycle status and legacy supply should be confirmed during quotation. The form is the appropriate route for current commercial terms without relying on stale listing information.
What is the price of the PCA9672D?
The current commercial price for the PCA9672D should be requested through the Request a Quote form on this page. The NXP product page states that the device is no longer manufactured, which can make availability and order routing depend on remaining inventory or approved legacy sourcing. Quote requests should specify the required ordering suffix, reel quantity, and production schedule.
Is the PCA9672D currently in stock?
Current stock status for the PCA9672D should be confirmed through the Request a Quote form on this page. The manufacturer identifies the product as no longer manufactured, so an ordinary active-production inventory assumption is inappropriate. Provide the required order code, annual usage, and target delivery schedule to obtain a current supply and lead-time response.
What are the key specifications of the PCA9672D that engineers should know?
The key PCA9672D specifications are eight quasi-bidirectional I/O ports, a 2.3 V to 5.5 V operating range, and I2C Fast-mode Plus communication up to 1 MHz with a 30 mA bus-interface drive capability. The device also includes three hardware address inputs, an interrupt output, and a reset input. It is identified by NXP as no longer manufactured and is packaged as a 16-pin SO device.

بيانات مرجعية هندسية لـ PCA9672D — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the PCA9672D when an existing design uses the 16-pin SO footprint and requires eight quasi-bidirectional ports, 1 MHz I2C Fast-mode Plus communication, three hardware address inputs, an interrupt output, and a reset input. Choose PCA9672D,512 when that is the ordering code required for procurement or manufacturing records; it is the same PCA9672 device rather than a different functional alternative. Do not substitute a generic 8-bit expander unless its package, pinout, port electrical characteristics, reset behavior, address scheme, and interrupt implementation all match. A similar GPIO count alone is not sufficient because other expanders may use a different package or a lower bus rate. Because NXP identifies the base product as no longer manufactured, the lifecycle plan should also address future availability, last-time-buy needs, and long-term production continuity before the design is released.

المقارنة مع البدائل

المعامل هذا المنتج PCA9672D,512
Brand NXP Semiconductors NXP Semiconductors
Package 16-pin SO 16-pin SO
Device Type 8-bit remote I/O expander 8-bit remote I/O expander
Number of I/O Ports 8 ports 8 ports
Operating Voltage Range 2.3 V to 5.5 V 2.3 V to 5.5 V
I2C Bus Frequency 1 MHz Fast-mode Plus 1 MHz Fast-mode Plus
Hardware Address Inputs 3 inputs 3 inputs
Interrupt and Reset Interrupt output and reset input Interrupt output and reset input
Port Type Quasi-bidirectional Quasi-bidirectional
Lifecycle Status No longer manufactured Orderable suffix of the no-longer-manufactured PCA9672D

أبرز الفروقات

  • Provides a 1 MHz I2C Fast-mode Plus interface (مقابلPCA9672D,512)
  • Combines eight ports with event-driven notification (مقابلPCA9672D,512)
  • Supports multiple devices on one I2C bus (مقابلPCA9672D,512)

ملاحظات التصميم

Route SCL and SDA as short, continuous traces with a solid ground reference beneath the bus. Place the I2C pull-up resistors at the physical end of the bus rather than beside the controller when several devices are present. Keep the PCA9672D bypass capacitor close to its supply pin and maintain a low-impedance ground return from the package. Confirm every signal against the manufacturer pin-description table before assigning the 16-pin SO footprint.

The PCA9672D operates across 2.3 V to 5.5 V, but the connected logic, pull-ups, LEDs, and external drivers each impose their own limits. Calculate the maximum high-level current through every I2C pull-up and the total current sourced by enabled output ports. Do not treat the interface's 30 mA drive specification as permission to exceed the individual port-current limit. Use suitable buffering or transistor stages for loads beyond the port rating.

Quasi-bidirectional ports can source current and sink limited current, so a high state is not necessarily equivalent to a push-pull output. Confirm the port topology and pull-up arrangement in the datasheet before connecting a load. Also avoid using the same address on multiple devices, and do not assume that a different 8-bit expander is pin-compatible merely because its register count and GPIO quantity match. The reset input should be driven only in accordance with its specified electrical behavior.

Although the interface supports 1 MHz I2C Fast-mode Plus operation, the usable rate depends on total bus capacitance, pull-up resistance, clock stretching, topology, and the electrical characteristics of every connected device. Use scope measurements at the slowest and fastest intended operating points if the bus includes long branches or long PCB traces. Keep high-current switching paths separate from SCL and SDA to minimize injected noise and ringing.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The manufacturer product summary identifies environmental quality information and a product-change notice, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations are present in the available records. These fields remain unknown rather than being inferred.

تم التحقق من البيانات في: 2026-11-14 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

PCA9672D datasheet PCA9672D pinout PCA9672D datasheet pdf PCA9672D application circuit PCA9672D equivalent PCA9672D replacement PCA9672D cross reference PCA9672D price PCA9672D stock NXP PCA9672D PCA9672D 1 MHz I2C expander PCA9672D 16-SO pinout

المكونات والمصطلحات ذات الصلة

NXP Semiconductors PCA9672D PCA9672D,512 PCA9672 I/O expander interface IC semiconductor I2C I2C Fast-mode Plus SCL SDA quasi-bidirectional GPIO hardware address input interrupt output reset input 16-pin SO package surface mount LED dimming industrial automation sensor interface remote control 2.3 V to 5.5 V operating voltage 1 MHz bus frequency
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر