PCA9672D - 8-Bit I/O Expander with 1 MHz I2C | NXP
MPN: PCA9672D ✗ پایان تولیدPCA9672D نمای کلی
An I/O expander is an interface IC that adds parallel digital input or output capability to a host controller over a serial bus. In the product hierarchy, the PCA9672D is an I/O expander within interface ICs and semiconductors. Its two-wire I2C connection reduces the number of host-controller pins required when a design needs additional control, status, or general-purpose I/O lines.
The principal features include eight quasi-bidirectional ports, I2C Fast-mode Plus operation up to 1 MHz, three hardware address inputs, an interrupt output, and a reset input. The 2.3 V to 5.5 V operating range permits use in both 3.3 V and 5 V systems. Quasi-bidirectional ports can be configured individually as inputs or outputs, allowing the same external connector or control interface to combine input and output signals.
The PCA9672D supports both interrupt-driven and polling-based host communication. An output port can generate an interrupt when a connected input changes state, allowing the host to handle events without continuously polling all eight inputs. The reset input provides a defined recovery path for the serial interface and port state. I2C address selection through three hardware address inputs permits multiple expanders on the same bus when their address straps are assigned differently.
Typical uses include LED status and control panels, keypad and switch interfaces, industrial automation modules, sensor gathering, alarm and monitoring equipment, and compact embedded control boards. The 1 MHz bus rate is particularly useful for LED dimming or moderate-rate control traffic, while the interrupt output improves responsiveness in event-driven systems.
Designers should verify the electrical characteristics of each quasi-bidirectional port, including its output-current capability and pull-up arrangement, before driving loads. The PCB layout should keep the I2C traces short, provide continuous ground references, and place bypass and pull-up components close to their associated pins. Firmware must also define startup states to avoid unintended outputs during reset.
This product page combines the manufacturer feature summary, package identification, lifecycle information, ordering-code details, and practical guidance for I2C expansion, event handling, reset behavior, and PCB implementation. It also distinguishes exact ordering variants from unrelated interface ICs that use similar functions but do not share the same package and pin arrangement.
جایگزینهای drop-in برای PCA9672D — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
PCA9672D,512
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PCA9672D مشخصات
| Device Type | 8-bit remote I/O expander |
| Number of I/O Ports | 8 ports |
| Port Type | Quasi-bidirectional |
| Serial Interface | I2C two-wire bidirectional bus |
| I2C Bus Frequency | 1 MHz Fast-mode Plus (Fm+) |
| I2C Interface Drive Capability | 30 mA |
| Operating Voltage Range | 2.3 V to 5.5 V |
| Hardware Address Inputs | 3 inputs |
| Interrupt Output | 1 open-drain interrupt output |
| Reset Input | 1 active-low reset input |
| بستهبندی | 16-pin SO package |
| نوع نصب | Surface mount |
راهنمای پیکربندی پین PCA9672D 16-pin so package
پیکربندی پین برای PCA9672D (پکیج 16-pin so package). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای PCA9672D.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
PCA9672D مناسب است برای 6 کاربردs: LED Status and Dimming Panel, Industrial Switch and Keypad Interface, Sensor and Alarm Input Aggregation, Remote Control and Relay Interface, Automated Test and Measurement Front End, Embedded Access and Security Control.
LED Status and Dimming Panel
The PCA9672D fits an LED status panel because its eight quasi-bidirectional ports can drive or sense multiple indicator channels while the host communicates through I2C. Fast-mode Plus operation up to 1 MHz permits efficient register updates, and the interrupt output can notify the controller when an externally monitored input changes. The 2.3 V to 5.5 V range supports both 3.3 V and 5 V logic systems. For PWM dimming, confirm the port current limit and use suitable transistor stages when an LED string exceeds the direct-drive capability. The design should also define each port's reset state so the panel does not illuminate unexpectedly during startup.
پیشنهادی
Industrial Switch and Keypad Interface
The PCA9672D can consolidate switch, keypad, or selector inputs into an embedded controller without dedicating eight host GPIO pins. Its eight quasi-bidirectional ports support mixed input and output use, while three hardware address inputs allow multiple expanders to coexist on one I2C bus with distinct addresses. The interrupt output reduces the need for continuous polling when a human-operated control changes state. In an industrial module, place the I2C pull-ups and bypass capacitor close to the device and keep the bus away from switching-node traces. Firmware should debounce mechanical contacts and confirm the exact port behavior in the manufacturer datasheet before finalizing the input circuit.
پیشنهادی
Sensor and Alarm Input Aggregation
The PCA9672D is useful for collecting several discrete sensor, alarm, or interlock signals through one two-wire interface. The host reads port states over I2C, and the interrupt output can signal a change so the controller can respond without continuously polling. Three hardware address inputs allow several expansion devices to be placed on the same bus when each receives a unique address configuration. Because the ports are quasi-bidirectional rather than dedicated high-current inputs, the external sensor must be compatible with the port's pull-up and input characteristics. The 2.3 V to 5.5 V operating range also helps align the expander with many industrial embedded controllers, subject to the device's temperature and EMC requirements.
پیشنهادی
Remote Control and Relay Interface
The PCA9672D can serve as the low-voltage control layer for a remote relay or switch bank. Eight outputs allow a host to activate and monitor multiple channels through I2C, reducing wiring compared with individual host-controller lines. For inductive or high-current loads, use suitable driver transistors or relay interfaces rather than driving the loads directly from the expander. The interrupt output can support feedback or change detection when a monitored line is connected to a port. The 1 MHz Fast-mode Plus interface helps the host update multiple channels efficiently, while the reset input offers a defined startup path. Production firmware should leave outputs in a safe inactive state until the host has initialized the device and validated the external circuitry.
پیشنهادی
Automated Test and Measurement Front End
The PCA9672D can extend a test-and-measurement controller with eight quasi-bidirectional lines for fixture control, status lamps, or discrete instrumentation signals. The I2C interface allows the host to update these lines over a compact two-wire connection, and Fast-mode Plus operation up to 1 MHz supports responsive fixture sequencing. A hardware interrupt can indicate a change on an input connected to the fixture, which is useful for asynchronous equipment events. The device's 2.3 V to 5.5 V range supports common laboratory and embedded logic levels. Keep sensitive analog and high-impedance measurement paths separate from the digital bus, use short ground returns, and check every port's electrical limit against the fixture before reducing resistance or changing logic levels.
پیشنهادی
Embedded Access and Security Control
The PCA9672D can support compact access-control hardware by connecting keypad lines, door-status inputs, indicator outputs, and local request signals to one I2C host interface. Three hardware address inputs permit several expansion devices to share a bus, and the interrupt output allows the controller to react promptly to a door or request event. The 2.3 V to 5.5 V operating range accommodates common embedded supply levels. Because security systems often contain long wiring runs, add appropriate input conditioning and protection rather than relying on the expander alone for surge or ESD protection. During reset, explicitly configure outputs to prevent unintended unlocks or alarm indications, and review the final pin assignments against the NXP datasheet before fabrication.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای PCA9672D — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | PCA9672D,512 |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 16-pin SO | 16-pin SO |
| Device Type | 8-bit remote I/O expander | 8-bit remote I/O expander |
| Number of I/O Ports | 8 ports | 8 ports |
| Operating Voltage Range | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| I2C Bus Frequency | 1 MHz Fast-mode Plus | 1 MHz Fast-mode Plus |
| Hardware Address Inputs | 3 inputs | 3 inputs |
| Interrupt and Reset | Interrupt output and reset input | Interrupt output and reset input |
| Port Type | Quasi-bidirectional | Quasi-bidirectional |
| Lifecycle Status | No longer manufactured | Orderable suffix of the no-longer-manufactured PCA9672D |
تفاوتهای کلیدی
- Provides a 1 MHz I2C Fast-mode Plus interface (در مقابلPCA9672D,512)
- Combines eight ports with event-driven notification (در مقابلPCA9672D,512)
- Supports multiple devices on one I2C bus (در مقابلPCA9672D,512)
یادداشتهای طراحی
Route SCL and SDA as short, continuous traces with a solid ground reference beneath the bus. Place the I2C pull-up resistors at the physical end of the bus rather than beside the controller when several devices are present. Keep the PCA9672D bypass capacitor close to its supply pin and maintain a low-impedance ground return from the package. Confirm every signal against the manufacturer pin-description table before assigning the 16-pin SO footprint.
The PCA9672D operates across 2.3 V to 5.5 V, but the connected logic, pull-ups, LEDs, and external drivers each impose their own limits. Calculate the maximum high-level current through every I2C pull-up and the total current sourced by enabled output ports. Do not treat the interface's 30 mA drive specification as permission to exceed the individual port-current limit. Use suitable buffering or transistor stages for loads beyond the port rating.
Quasi-bidirectional ports can source current and sink limited current, so a high state is not necessarily equivalent to a push-pull output. Confirm the port topology and pull-up arrangement in the datasheet before connecting a load. Also avoid using the same address on multiple devices, and do not assume that a different 8-bit expander is pin-compatible merely because its register count and GPIO quantity match. The reset input should be driven only in accordance with its specified electrical behavior.
Although the interface supports 1 MHz I2C Fast-mode Plus operation, the usable rate depends on total bus capacitance, pull-up resistance, clock stretching, topology, and the electrical characteristics of every connected device. Use scope measurements at the slowest and fastest intended operating points if the bus includes long branches or long PCB traces. Keep high-current switching paths separate from SCL and SDA to minimize injected noise and ringing.
اطلاعات انطباق
The manufacturer product summary identifies environmental quality information and a product-change notice, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations are present in the available records. These fields remain unknown rather than being inferred.